Agria 5500 CT User manual

agria-Werke GmbH • D-74219 Möckmühl • Tel. [phone] •Fax [phone]
TT
TT
Tool Carool Car
ool Carool Car
ool Carrierrier
rierrier
rier
5500 CT5500 CT
5500 CT5500 CT
5500 CT
07.07
998590
Quick start guide

5500 CaneThumper®
Quick start guide
Page 2 of 7 07.07 B
Before commissioning the machine please read operating instructions
Check all fluids, settings, warnings and safety instructions !
Check the machine
Prior to operating the machine and after 10 hours
Check oil level
Fill if level is below min Clean cooling system from dust and dirt If air filter indicator changes to red change filter element
Operating instruction
in black box on board Service manual and documents
with the machine Tools in black toolbox
max
min
To avoid early abrasion or damages
Ensure the required adjustment on hand levers

5500 CaneThumper®
Quick start guide
Page 3 of 7 07.07 B
Start motor (step by step)
Switch off motor
Let motor run at increased idling speed for a minute to cool down
and to avoid carbon to deposit on the injection valve before machine is turned off !
(1) Push safety circuit lever
(left handlebar) (2) Pull clutch lever (left handlebar) (3) lock clutch lever with pawl (left handlebar)
(4) Set speed control lever to max
(right handlebar) (5) Pull rope hard and fast to start the engine (stand to left side) (3) Let rope glide back carefully do not let snap
Push and lock clutch
(for reference see start) Set speed control to “STOP” (right handlebar) Emergency stop
release the safety lever

5500 CaneThumper®
Quick start guide
Page 4 of 7 07.07 B
Operations
Wear individual safety equipment like safety shoes and ear plugs !
Changing gears 1-4 and F/R requires pulling the clutch ! Do not shift the gears by force .
If necessary pull and release the clutch to bring the gears in easy switchable position !
Direction of motion forward / neutral / reverse (right handle bar)
! The gears must only be changed by pulling the clutch ! (For drive and stop please see next chapter)
Drive and Stop
Hold safety lever, pull clutch
(left handlebar)
(safetybrake is set to on)
Choose gear with the shifting lever
gears 1/2/3/4=1,0/1,5/1,9/7,1 km/h
(right handlebar)
For F/R motion
please see next chapter
(right handlebar)
Hand lever released
= forward motion Center position pawl engaged = neutral position Hand lever pulled = reverse motion
Set speed control to max
move lever forward
(right handlebar)
Release the clutch slowly
Tool carrier moves
(left handlebar)
Pull clutch tool carrier stops
and safety breake is set to on
(left handlebar)

5500 CaneThumper®
Quick start guide
Page 5 of 7 07.07 B
Differential Lock (right handlebar)
Release throttle and discharge drive for easy on/off switching the differential Lock
Move the machine without the motor running
Differential Lock engaged =
improved traction
forward and reverse
Differential Lock disengaged =
easy steering especially in curves Set pawl to disengage Differential
Lock
permanently
(1) Set forward reverse lever
to neutral position (use clutch),
lock lever with pawl
(right handlebar)
(2) Release clutch lever
to disengage safety brake
(left handlebar)
(3) Disengage differential lock
for easy steering
lock lever with pawl
(right handlebar)

5500 CaneThumper®
Quick start guide
Page 6 of 7 07.07 B
Coupling and decoupling Implements
Mount and dismount attachments only with engine switched off !
PTO shifting
Shifting PTO requires pulling the clutch ! Do not shift the PTO by force .
If necessary pull and release the clutch to bring the gears in easy switchable position !
Handlebar adjustment
1. Disconnect PTO shaft (attachment)
= move lever (4) to pos. “0”
2. Ensure clean surfaces
Slide pegs (2) of tool carrier
into hooks (3) of attachment
make sure attachment is properly
centered and flat fitted
Fold both eye bolts (1)
over coupling flange
tighten cap nuts evenly
Connect fork end of shift rod
and shift lever with bolt To disconnect PTO shaft, push lever To connect PTO shaft, pull lever
Height adjustment
loosen both lock nuts (A)
and hex head bolts (B)
bring the handlebar to desired height
fasten bolts and nuts
Lateral adjustment
Pull ball handle (B/1) upwards
turn handlebar into desired
position / release ballhandle

5500 CaneThumper®
Quick start guide
Page 7 of 7 07.07 B

Your local agria specialist dealer: