AIC Libra User manual
Libra
Server MotherBoard
User Manual
Document Number: MAN-00207-A
1
Contents
Contents............................................................................................................................................................0
SafetyInformation.............................................................................................................................................2
AboutThisUserManual.....................................................................................................................................3
Chapter1............................................................................................................................................................4
1.1 General Information........................................................................................................................4
1.2 Specifications....................................................................................................................................4
Chapter2...........................................................................................................................................................6
2.1 Central Processing Unit (CPU).......................................................................................................6
2.2 System Memory................................................................................................................................9
Chapter3.........................................................................................................................................................13
3.1 Motherboard block diagram......................................................................................................13
3.2 Motherboard Layout.....................................................................................................................14
3.3 Motherboard Content List...........................................................................................................15
3.4 Internal Connectors/Jumpers.....................................................................................................16
Chapter4..........................................................................................................................................................29
4.1Updating BIOS........................................................................................................................31
Chapter5.........................................................................................................................................................33
5.1Method1(UsetheBIOSsetup)..................................................................................................33
5.2Method2(UseaDostool‐Syscheck).................................................................................................36
5.3ConnecttoBMC...................................................................................................................................38
5.4UpdatingBMCFirmware......................................................................................................................42
Chapter6.........................................................................................................................................................43
2
SafetyInformation
When installing, operating, or performing maintenance on this equipment, basic safety
precautions, as listed below, should always be followed to reduce the risk of fire, electric
shock, and personal injuries.
Read and understand all instructions.
Observe warnings and instructions marked on the product.
For proper mounting instructions, please consult the User’s Manual provided with
the product.
Do not place this product on an unstable cart, stand or table which might cause
the product to fall and sustain serious damage.
Install only equipment identified in the User’s Manual provided with this product.
Use of other equipment might cause improper connection of circuitry that might
lead to fire or personal injuries.
This product should be operated only from the type of power source indicated on
the marked label. If you are uncertain about the type of power supply in your
area, consult your dealer or the local Power Company.
Disconnect the power supply module when removing power from the system.
Unplug this product from the wall outlet before cleaning. Use a damp cloth for
cleaning. Do not use liquid cleaners or aerosol cleaners.
Do not use this product near a water source such as a wet faucet.
Never push objects of any kind into this product through open slots as they may
touch dangerous voltage points or short out parts that could result in fire or
electric shock. Never spill liquids of any kind on the product.
Do not block or cover slots and openings in the unit as they are for ventilation to
protect the unit from overheating. Do not place the product in a built-in
installation unless proper ventilation is available.
To reduce the risk of electric shock, do not disassemble this product. Service
should only be performed by trained personnel. Opening or removing covers
and/or circuit boards may expose you to electric or other risks. Incorrect
reassembly can cause electric shock when the unit is subsequently used.
Risk of explosion is possible if battery is replaced with an incorrect type. Dispose
used batteries according to the instruction.
This product is equipped with a three-wire grounding type plug, a plug with a third
(grounding) pin. This plug is intended to fit only into a grounding type power
outlet. This is a safety feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace the outlet. Do not defeat the safety purpose
by removing the grounding type plug. Do not use a 3-to-2 prong adapter at the
receptacle. Use of this type of adapter may result in risk of electric shock and/or
damage to this product.
3
AboutThisUserManual
This document provides a detailed description of the Libra including:
The General Features of the Product
Motherboard Settings
BIOS Configuration and Settings
BMC Configuration and Settings
4
Chapter1.
ProductIntroduction
1.1 General Information
Libra, a server grade mother board supports two Intel®Xeon®processor E5-2600 V3
series.
1.2 Specifications
Dimensions (with chassis ears/protrusions)
W x D mm : 305 x 330
inches : 12 x 13
Motherboard
Motherboard Libra
Processo
r
Processor Support Dual LGA2011-3 (Socket –R3) to support two Intel® Xeon® processor E5-
2600 V3 series
QPI/DMI Speeds 8 GT/s, 5 GT/s, 2.5 GT/s
Chipset
Chipset Support Intel®C612 chipset
System Memory
5
System Memory
• 4 memory channels per CPU socket, 4 channels with 2DPC
• 16 DIMM slots support up to:
- 256GB (@4Gb) / 512GB (@8Gb) DDR4 1866/2133 RDIMM SR, DR
- 512GB (@4Gb) / 1024GB (@8Gb) DDR4 2133 LRDIMM QR
BIOS
BIOS Type •INSYDE 16MB
• SPI (Serial Peripheral Interface) FLASH Interface
BIOS Features
• EFI BIOS
• ACPI
• PXE
• WOL
• AC loss recovery
• IPMI KCS interface
• SMBIOS
• Serial console redirection
On-Board Devices
Serial ATA Built-in SATA controller with RAID support on Intel®C612 chipset
Support •8 x SATA3 ports
IPMI
Aspeed AST2400 BMC
•Intelligent Platform Management Interface 2.0 (IPMI 2.0)
•iKVM, Media Redirection, IPMI over LAN, Serial over LAN
•SMASH support
Network
Controllers
•Intel®X540 10 GbE controller
•Intel®I350 1GbE controller(Optional)
•Intel®I210 PCIe single-port 1GbE controller
•Intel®I217 1GbE PHY
Graphics Aspeed AST2400 graphics controller
•PCIe x1 VGA/2D controller
•1920x1200@60Hz 32bpp
Rear I/O
LAN 2 x RJ45 single ports(10 GbE / 1 GbE)
1 x RJ45 dual ports
USB 1 x USB ports
VGA 1 x VGA port
Serial Port 1 x external DSUB-9 serial port
System Management
System
Management
• IPMI 2.0 compliance
• iKVM support (KVM over IP)
• Media redirection
• Smart fan speed control
• Remote power on/off/reset
• Temperature, fan, voltage, PSU sensor monitor
• System ID / System fail indicator
• SEL message alarm through mail
• SNMP support
• Intel NM
Operating Environment
Environmental
Specifications
• Operating Temperature: 0 ~ 55°C
• Operating Altitude Condition: 0 ~ 10K feet
• Storage Temperature: -40° ~ 70°C
• System Relative Humidity: 5% to 95% non-condensing
6
Chapter2.
HardwareSetup
2.1 Central Processing Unit (CPU)
2.1.1 Installing the CPU
1. Press the load lever to release the load plate.
2. Lift the load plate.
Caution : When unpacking a processor, hold the processor only by its
ed
g
e
s
t
o
a
vo
id t
ouc
hi
ng
the
con
ta
c
t
s
.
Loadlever
Loadplate
7
3. Remove the processor protective cover from CPU socket.
4. Align the processor cutouts against the socket notches.
5. Close the load plate & load lever.
Presstoclose
Processorprotectivecover
Caution: The pins of the processor socket are vulnerable and
easily susceptible to damage if fingers or any foreign objects are
pressed against them. Please keep the socket protective cover on
when processor is not installed.
Cutouts
8
2.1.2 Installing the CPU Heatsink
To install the CPU heatsink:
1. Place the heatsink on top of the CPU, ensuring that the four fasteners match
the holes on the motherboard.
2. Tighten the four screws in a diagonal sequence, a couple of turns at a time,
until all four screws are secure and the heatsink is securely fastened to the
chassis.
Note: Apply thermal paste to the bottom of heatsink and spread in
an even thin layer before installing the heatsink.
9
2.2 System Memory
This server board supports up to sixteen DDR4 1333/1600/1866/2133 Registered ECC
SDRAM(RDIMM) / Load-Reduced DIMM (LRDIMM).
10
1. Populate DIMMs in the following order:
DIMM
Numbers DIMM arrangement
2 DIMMs
CPU1 JCPU0
JDIMM_G0 JDIMM_A0
4 DIMMs
CPU1 JCPU0
JDIMM_G0
JDIMM_H0
JDIMM_A0
JDIMM_B0
6 DIMMs
CPU1
JCPU0
JDIMM_G0
JDIMM_H0
JDIMM_E0
JDIMM_A0
JDIMM_B0
JDIMM_C0
8 DIMMs
CPU1 JCPU0
JDIMM_G0
JDIMM_H0
JDIMM_F0
JDIMM_E0
JDIMM_A0
JDIMM_B0
JDIMM_D0
JDIMM_C0
10 DIMMs
CPU1 JCPU0
JDIMM_G0
JDIMM_G1
JDIMM_H0
JDIMM_F0
JDIMM_E0
JDIMM_A0
JDIMM_A1
JDIMM_B0
JDIMM_D0
JDIMM_C0
11
12 DIMMs
CPU1 JCPU0
JDIMM_G0
JDIMM_G1
JDIMM_H0
JDIMM_H1
JDIMM_F0
JDIMM_E0
JDIMM_A0
JDIMM_A1
JDIMM_B0
JDIMM_B1
JDIMM_D0
JDIMM_C0
14 DIMMs
CPU1 JCPU0
JDIMM_G0
JDIMM_G1
JDIMM_H0
JDIMM_H1
JDIMM_F0
JDIMM_E1
JDIMM_E0
JDIMM_A0
JDIMM_A1
JDIMM_B0
JDIMM_B1
JDIMM_D0
JDIMM_C1
JDIMM_C0
16 DIMMs
CPU1 JCPU0
JDIMM_G0
JDIMM_G1
JDIMM_H0
JDIMM_H1
JDIMM_F1
JDIMM_F0
JDIMM_E1
JDIMM_E0
JDIMM_A0
JDIMM_A1
JDIMM_B0
JDIMM_B1
JDIMM_D1
JDIMM_D0
JDIMM_C1
JDIMM_C0
12
2. Unlock a DIMM socket by pressing the retaining clips outward.
3. Insert module vertically and press down until it snaps into place.
Note: DIMM notch and socket bump must align as shown.
DIMMnotch
13
Chapter3.
MotherboardSettings
This section describes the jumpers, internal connectors, and internal LEDs setting on
Libra motherboard. Motherboard layout and important jumper settings are listed as
below.
3.1 Motherboard block diagram
14
3.2 Motherboard Layout
15
3.3 Motherboard Content List
Connectors Location Connectors Location
1 Ethernet (Single Port) LAN1,LAN2 28 Intruder JINTRUDER
2 Ethernet (Dual Port) RJ45 29 PMBUS JPMBUS
3 USB Port (Dual Port) USB3.0 30 SPI ROM Socket JSPI
4 COM Port COM 31 Speaker JSPKR
5 VGA Port VGA 32 BMC Reset JBMC_RST
6 Power Supply (4x2 pin) JPWR1 33 BMC Disable JBMC_DIS
7 Power Supply (7x2 pin) JPWR2 34 System PG Lock JPG_LOCK
8 Power Supply (4x2 pin) JPWR3
35
BMC Buzze
r
JBUZZER
9 SATA-DOM Power JDOM_PWR 36 BIOS Recovery Mode J6
10 SSI Front Panel JFRNT_SSI 37 ME Force Recovery Mode J9
11 Serial ATA SATA1~
SATA4 38 Flash Descriptor Security
override J7
12 SSATA SATA5~
SATA8 39 No Reboot(Watch Dog) J8
13 VGA Pin header JVGA_INT 40 NTB
(Non-Transparent Bridge) JNTB
14 COM Port JCOM4 41 PCH GPIO JPCH_GPIO
15 Front USB JUSB_INT 42 LCM(COM Port) JLCM
16 CPU XDP header JCPU_XDP 43 LAN3/LAN4 JLAN1/JLAN2
17 CPU Sockets CPU0/CPU1 44 SAS Drive Error LEDs J2
18 Debug port JLPC_DP 45 SAS Drive Active LEDs J3
19 TPM Port JTPM 46 SAS ICE0 J4
20 BMC debug Port JBMC_DP 47 SAS UART0 J5
21 BMC GPIO JBMC_GPIO 48 LAN3/LAN4 LEDs J10
22 SGPIO JSGPIO 49 External Thermal Sensor J19/J20
23 SSGPIO JSSGPIO
50
SFF-8643 CONN
CN1,CN2
24 Clear CMOS JCMOS 51 NGFF M.2 CONN JNGFF
25 BMC_I2C10 JBMC_I2C10 52 FIN_4P J1,J17,J18
26 BMC IPMI JBMC_I2C1 53 FIN_6P J11~J16
27 Battery Socket JBAT 54
16
3.4 Internal Connectors/Jumpers
17
Connectors/Jumpers Description
JFRNT SSI SSI Front Panel
1. +3.3V_DUAL
2. +3.3V_DUAL
3.KEY (no pin)
4.+5V_AUX
5.PWR_LED#
6.UIDLED_OUT#
7. +3.3V
8.SYS_HEALTH#2
9.HD_LED#
10.SYS_HEALTH#1
11.SW_PWR_BTN#
12.LAN1_LINK_UP
13. GND
14.LAN1_TRAFFIC
15.SW_RST_BTN#
16.I2C8SDA
17. GND
18.I2C8SCL
19.UID_SW_IN#
20.INTRUDER#
21. NC
22.LAN2_LINK_UP
23.FP_NMI_BTN
24.LAN2_TRAFFIC
J1 Fan Header 1. GND
2. +12V
3. FAN9_TACH
4. PWM6
J17 Fan Header 1. GND
2. +12V
3. FAN8_TACH
4. PWM5
J18 Fan Header 1. GND
2. +12V
3.FAN7_TACH
4.PWM4
JPG_LOCK System PG Lock
(Jumper)
Open/Normal (Default)
Short/Lock
JPWR3 Power Supply
1.GND
2. GND
3. GND
4. GND
5. +12V
6. +12V
7. +12V
8. +12V
JDOM_PW
R SATA-DOM Power 1.+5V 2.GND
J11 Fan Header
1. GND
2. +12V
3. FAN1_TACH
4. PWM1
5. FAN1A_PRSNT_N
6. LED_FAN1A_FAULT
18
J12 Fan Header
1. GND
2. +12V
3. FAN2_TACH
4. PWM1
5. FAN1B_RSNT_N
6. LED_FAN1B_FAULT
J13 Fan Header
1. GND
2. +12V
3. FAN6_TACH
4. PWM3
5. FAN3B_PRSNT_N
6. LED_FAN3B_FAULT
J15 Fan Header
1. GND
2. +12V
3. FAN5_TACH
4. PWM3
5. FAN3A_PRSNT_N
6. LED_FAN3A_FAULT
J14 Fan Header
1. GND
2. +12V
3. FAN4_TACH
4. PWM2
5. FAN2B_PRSNT_N
6. LED_FAN2B_FAULT
J16 Fan Header
1. GND
2. +12V
3. FAN3_TACH
4. PWM2
5. FAN2A_PRSNT_N
6. LED_FAN2A_FAULT
J19 External Thermal
Sensor 1. HM_TD8+ 2. HM_TD8-
J20 External Thermal
Sensor 1. HM_TD7+ 2. HM_TD7-
JUSB_INT Front I/O USB Header
1. +5V_USB23
2. PCH_FP_USB3_RX_N2
3. PCH_FP_USB3_RX_P2
4. GND
5. PCH_FP_USB3_TX_N2
6. PCH_FP_USB3_TX_P2
7. GND
8. PCH_FP_USB2_N2
9. PCH_FP_USB2_P2
10. PCH_USB_OC#23
11. PCH_FP_USB2_P3
12. PCH_FP_USB2_N3
13. GND
14. PCH_FP_USB3_TX_P3
15. PCH_FP_USB3_TX_N3
16.GND
17. PCH_FP_USB3_RX_P3
18. PCH_FP_USB3_RX_N3
19. +5V_USB23
20. KEY (no pin)
19
Internal Connectors/Jumpers (Continued)
Other manuals for Libra
1
Table of contents
Other AIC Motherboard manuals
