Aiphone TB-M Series User manual

sseoeio0
oe
>
AIPHONE
TB-M Series
INTERNAL TELEPHONE SYSTEM
Models: TB-10M
| = TB-20M |
INSTALLATION & OPERATION MANUAL
CONTENTS
FOYS TEMNOUTENE & COMPONEN TSi a a 1
2 NAMES &FEATURE Gorai E aE E E E 2
3 PRECAUTIONS ON INSTALLATION & WIRING cccciccesscctaceiseescsccsvesivencvesbesteuecvshiaideuwsccrcecendedndenedatsteanesce 3
A N RING eea a a E E A a tA e ae 4
I MOUNTING renier S r A 9
OR TRATON rria N E N N 10
7 TECHNICAE PRECAUTIONS serions aE O 11
G: GOIN Geremia a AA E NN 12
Bee
| SYSTEM OUTLINE & COMPONENTS
Hi Sysiem outline
The TB-M is an internal telephone type system, expandable up to 60 subs and 2 masters.
Communicates with TB-SE handset subs and IE/IF door stations.
ia
Mi Package contents
Master station (TB-10M or TB-20M)
Directory card & cover
Screws-pack (2 types, ea. 4 pcs)
Wall-mount cradle
Installation & Operation Manual
TB-10M or TB-20M
w/TB-20G or TB-40G
QQYO”
E Components available
TB-SE IF-DA, etc. TB-AD1 TB-AD10 TB-20G TB-40G
Sub station IE/IF Series
door station
40-call add-on
selector
20-cail add-on
selector
10-call door
station adaptor
1-call door
station adaptor
(up to 3)
TB-M components: TB-10M, TB-20M, TB-20G, TB-40G, TB-AD1 and TB-AD10 are NOT compatible with TB-10T and TB-20T.
TB-RC sub can be used with TB-M.
SES E

NAMES & FEATURES
E Names & functions
TB-10M
and
TB-20M
master
station
is
streamline
and
modernly
designed.
The
master
console
may
be
placed
on
desk
or wall-mounted.
Power on switch |
(on rear panel) l
Power on & Piug-in connector
in-use LEDs (on the back)
Station-select or
call button with LED
ay
fe
E>
(
LF
rr
Directory
card
z
EZY
and
cover
Receive
&
call
tone
405
mm
volume
controls
/
16
Transfer
switch
&
LED
TB-10M
with
TB-20G
add-on
selector
The
selector
switch
bank
is
aligned
vertically,
with
each
station
having
its
own
directory.
Station
numbers
count
top
to
bottom
1
to
10
on
first
switch
bank,
and
11
to
20
on
the
second
switch
bank
of
TB-20M.
The
supplied
directory
card
and
cover
can
be
attached
from
the
left.
Features
Transfer
switch
and
LED
in
the
center
of
front
panel.
Single
transfer
button
automatically
connects
the
master
with
the
next
TB-SE
sub
that
has
called
(max.
2)
TB-20G
or
TB-40G
add-on
selector
plugs
into
TB-M
back
panel,
and
can
be
placed
on
either
side
of
master.
W@ Features
-
TB-20G
or
TB-40G
add-on
selector
connects
additional
TB-SE
subs,
allowing
system
expansion.
- One or dual-master configuration.
e
TB-AD1
adaptor
connects
TB-M
with
an
IE/IF
Series
audio
door
station
(up
to
3).
-
For
4
to
max.
10
doors,
use
a
TB-AD10
adaptor.
Or
alternatively,
TB-ADM10
adaptor
for
max.
10
PanTilt
door
stations.
Allows
TB-M
to
communicate
and
monitor
each
MY
door
station
audio-visually
either
selectively
or
all
in
succession.
Refer
to
the
TB-
ADM10
Manual.
-
Call
extension
IER-2
allows
incoming
call
tone
to
be
heard
at
a
remote
location.
-
Master
station
can
call
sub
by
tone,
and
optional
external
buzzer.
spe

=} PRECAUTIONS ON INSTALLATION & WIRING
*
++ + *
+
Do not attempt to install or connect wires on TB-(10,20)M equipment while system's power
supply is turned on.
TB-(10,20)M masters, TB-SE subs, and related equipment, except door station, are designed for
indoor use only. Do not install outdoors.
Do not connect any other power source than specified on terminals IN AC15-16V or DC18V.
Doing so can damage the TB-M equipment.
Do not open any TB-(10, 20)M system components. Ask qualified personnel.
All the products of other manufacturers, power supply, buzzer, etc. used for TB-(10,20)M, are not
within our warranty, and must be used under manufacturer or distributor's specifications and warranty.
Do not mount TB-(10,20)M equipment in the following places, as it may cause the system to
malfunction:
¢ High or extreme cold temperature areas: under direct sunlight, near equipment that varies in
temperature, front of air-conditioner, inside refrigerating warehouse, etc. _
¢ Places subject to moisture or humidity extremes
e Places subject to environmental conditions, such as iron dust, dust, oil, chemicals, etc.
TB-(10,20)M is an electrical appliance, which must not be subjected to water, or any other liquid.
Weather conditions, such as lightning storms, may cause damage to TB-M equipment. It is suggested
to take protective measures as follows;
e When an AC transformer is used
TB-10M
TB-20M
AC trans.
AC 15- 16V
Install
a
surge-arrester
or
DC
18V
(discharging voltage: 100~180V) Srde:
at a point close to the output, == ane
taken to earth ground.
— Grounded
e When a DC power supply is used:
On the power supply with grounding terminal, be sure to take the terminal to earth ground.
In this case, it is not necessary to connect a surge-arrester.
When using a power supply that has no grounding terminal, install a surge-arrester in the same
manner as stated above. Surge-arrester SA-1 is available from Aiphone.
Cable requirements
Use 2-conductor cable (twisted or non-twisted) homerun to each sub station (0.65 ~ 1.0mm¢,,
22 ~ 18AWG).
Before TB-(10,20)M is actually installed, the contents on pages 4 ~ 9 must be thoroughly read
and understood.

4, WIRING
E Terminal-block layout
TB-10M
«<qa— Connect power supply to
TB-M Master station _
(Max. 25m/1.0mm¢ , 80/18AWG)
alee or
[ |} AC15-16V
~<q@—— Each E terminal may have
one to three wires from
TB-SE terminal 2.
% 2 wires from TB-SE subs must
not be made common at any
other point than on the
TB-M terminal block.
H H 8l] te] le N] fel fed FS) e st E]
Ñ <
HH H [al [©] le] Sy e e e] e bs) E
— N <
lo] l) H H! El D E al m mA E a a im lo] la] H] [A] E Bl 2 [Oo] fea) a e fee] e [ee E E
(=) fis] (cs) S al e A Lee} (es) e a fr) [es] fem] ra
TB-AD1
OON H O e E H
A (fl [Sl [2] e D el e e e N
5] 3 [8] le] [o>] N] E fe) a] fel e] E
i
N <
T
=] A a E a al al ll [eo] S e e e e e |e) fe) ea
Do
Da
Da
D7
Da
55
Da
oa
Da
D
E Meaning of terminal symbols ©
E terminal is common calling and communication line.
No. 1~40 terminals are selective station points, providing selective calling and communication.
C & M terminals are master-to-master communication.
R & T terminals are master-to-door adaptor transmit and receive lines.
S & S terminals are call tone output to IER-2 call extension speaker.

E TB-10M single-master system with a door station
¢ The # terminals on the master station connect to
TB-SE terminal 1 on each TB-SE sub. These numbers
ial become the sub's station number, numbered from
the top on each 10-button row.
IF-DA TB-AD1
* 2 parallel wires per TB-SE sub, nonpolarized.
Be sure to run each pair of wires directly to
TB-M master.
E line in each pair should not be connected at
any other point of cable than E terminals on
TB-M, which can accomodate 2 ~ 3 TB-SE subs.
Master station
TB-10M ;
IN
AC 15-16V
or DC18V
To: power supply
Sub station
Door adaptor
TB-AD1
—
2
10| ~¢— Any # terminal on T
add-on selector.
Cail extension
IER-2
(one per TB-M)
===
aS
=
i
th
ae
—
= =z
a
===>
=
i
=
i
Mi
ad
4
I
The master can select the door station for audio monitoring at any time. The call
announce pretone is selectable.
Set the switch to ON position for pretone, removing the cover of front case.
TB-AD1
DC12V input
E Wiring distance
TB-M to TB-SE sub
0.8mm | 1.0mm AWG _| 22AW
Distance | 400m | 600m | 900m 1,300' | 2,000' | 3,000'
_22AWG | 20AWG |
WL
HONEOCEBA
TB-AD1 to audio door station
S2AWG | 20AWG | 18AWG
‘Distance | 500° | 750° | 1,200'
TB-M to TB-AD1
1.0mm 22AWG | 20AWG | 18AWG
150m 210'_| 330!
Pre-tone sounds at door
Station when selected from
TB-M master. The feature
can be muted by switching
to OFF.

E TB-10M single-master with TB-(20,40)G add-on selector
e TB-M master, with a TB-G add-on selector,
expands its capacity up to 60 substations.
Choose the master and add-on selector to
meet your system's requirements.
Master station
TB-10M
IN
AC 15-16V
or DC18V
To: power supply
Sub station
Add-on selector
TB-20G
Door adaptor
Sub station
TB-SE
i 1 1
Hi
lE]. [E] 2
E 2
[E]
| 4 1
14 [E] 2
,
z
12V
“12V|
<—
x%
Do
not
connect
any
15
(EI
2
ower source here. 6 Ceni]
R
16
:
\ J a Call extension E
r TB-M) u a ay
E
9 1
18 [E! >
[E] | 10 1 |
19 2)
20
Connector
% Up to 3 TB-AD1 door station adaptors per TB-M.
5 wires homerun to TB-M.

E TB-20M single-master with up to 10 door stations
In place of TB-SE handset subs, TB-M master
may have max. 10 door stations, by using a
TB-AD10 adaptor.
Master station
TB-20M
IN
IAC 15-16V |
[or DC18V |
To: power supply
Sub station
10-call door adaptor
% Do not connect any
power source here.
Cail extension
IER-2
(one per TB-M)
TB-AD10,
10-call
door
adaptor
may
be
wired
to
any
#
terminal
on
TB-M
or
TB-G
add-on
selector,
connecting
max.
10
IE/IF
door
stations.
Features
two-way
calling
and
communication
with
door
TB-AD10
Station,
including
optional
pretone.
Set
the
switch
to
ON
position,
if
pretone
to
door
is
required.
W
Wiring
distance:
LZ
TB-M
to
TB-AD10
f
»
AWG
|
22AWG
ZOAWG | 18AWG
= K
ON
H
4
OFF
210' | 330!
TB-AD10 to audio IF-DA
| Diameter | 0.65mm/ 0.8mm AWG | 22AWG | 20AWG | 18AWG
500° | 750' | 1,200
a a

E TB-M dual-master system
prone eee eeene n-ne e Common TB-SE sub rings two TB-M Masters.
a Single-pair
i
a
i
i
|
e
Each
master
can
call
TB-SE
sub
selectively.
il
BROS
7
nonposanzed |
l
i
|
( TB-SE ©
Master-to-master
communication.
IF-DA
TB-AD1
=
he:
en
|
|
j Į
j
|
TB-10M E Gone Area
TB-SE
2-pairs ! [
polarized: \\
CPS
TB-10M
Master station
TB-10M
IN
AC 15-16V
or DC18V
Master station
TB-10M
IN
AC 15-16V
or DC18V
Polarized
4 To power supply
i
E|
2
E|
3
E|
4
Door adaptor ar
TB-AD1 so
Sub station
~«t— Designate any # terminal
for TB-AD1
a <«— k The number terminal
E jumpered to “M” at each
EEE EE Mi master establishes master
C -to- master communication.
F 12 ~t— * Do not connect 12V
5 any power source T
c= R7 Call extension i Call extension
IER-2 S IER-2
H : TH
* IMPORTANT |
Do not use the following wiring methods. They will cause the system E Wiring distance:
Between TB-M masters
i AWG 22AWG | 20AWG T 18AWG
1,000' | 1,570
to malfunction:
Do not parallel sub station wires Door adaptor TB-AD1(10) can only
between TB-M master stations. be wired to one master. Doors
Wiring from TB-SE must be cannot call both master stations.
homerun to EACH master station.
E:

E Connecting a buzzer at a TB-SE sub
When called by TB-M master, buzzer is
activated
and
on
TB-SE
sub,
call
tone
sounds
at reduced volume.
TAR-3
relay
activates
an
AC-operated
buzzer:
AC
240V,
0.3A.
DC-operated
buzzer
must
be
mechanical
type:
DC
24V,
1.0A.
Do
not
use
DC
electronic
buzzer.
MOUNTING
WE TB-(10,20)M with TB-(20,40)G
Buzzer
TB-M
master
To : power source
TAR-3
DC6V, 160mA
Orange
shorting link.
PS-6D
power supply
(SKK-620
in USA)
Remove
2
screws
on
front
panel,
removing
the
cover
on
upper
end
and
area/section
plate.
Lift
off
front
case
holding
sides
at
top.
Disconnect
the
intercom
by
unplugging
the
connector.
Open
a
cable
inlet
hole
(rubber
part)
on
bottom
of
chassis.
Pull
in
cable(s),
and
make
wire
terminations.
Use
attached
cable
clamps(s)
for
neat
and
secured
connection.
Reconnect
and
mount
front
case
to
chassis,
attaching
the
cover
and
plate
in
place.
When
wall-mounting,
separate
the
front
panel
from
chassis,
as
explained
above.
Install
the
chassis
upside
down
on
the
wall,
onto
a
single-gang
or
two-gang
box.
Desk-top mounting
Area / section plate
Lift
off
front
case
holding
Screws
sides
at
top.
hole.
Open a knock-out
Wail-mounting
Lift off front case holding sides
at top.
Single-gang or
2-gang box
aw D
Screws FTRS n
Fy S
Í
Chassis mounts upside down.
*
TB-M
master
wall-mounts
with
TB-G
(and
TB-AD10)
attached.
Decide
the
exact
location
of
TB-M
master,
and
use
the
following
measurements
to
mount
the
add-on
components.
TB-M master TB-G add-on TB-AD10 door
selector adaptor
Centers of each chassis
(or gang boxes)
Wali-mounting guide
Master Attached
TB-10M TB-AD10
|
TB-AD10
|
2025,8"
|
—
|
=
TB-20M
|
TB-40G_[15.0,
12-1/2'|
TB-AD10
|
225.0,
9"
_
240.0,9-v2"|
—
|
—
|

OPERATIONS
ER Single TB-M system Speaker for call-in tone Power on LED
TB-(10, 20)M master communicates with 10 or |
20 TB-SE subs. TB-20G or TB-40G add-on |
communicates with 20 to 40 additional subs. In-use LED
l indicates TB-M master is not put
in standby. Make sure handset is
properly placed.
Attach the directory &
M -Z 4 cover from left side to
LAA RZ LÈ
WY BS
QY
Receiver
(upper)
&
call
tone
|
Call
in
LED
p
volume
controls
(3
levels)
Also
indicates
waiting
for
transfer of call
Transfer switch & LED ,
Station-select button
E TB-M single-master system
Calling
and
receiving
.
|
To
call
a
TB-SE
sub,
the
other
master
or
audio
door
station
pick
up
Baa ence n for handset and depress a station-select button. When called by
a tremolo tone, pick up and depress the LED-lit select button. LED
ed LED ae Pig aor l
remains on while in communication. Communicating TB-M is
notified of a call with a lit LED only. The audible call tone will
resume when the handset is hung up.
Do not press more than one buttons,
when calling.
Receiving a call from audio IE/IF door station
When the door station places a call with call button, a tremolo tone
is activated on the TB-M, which stays on approx. 40 seconds. The
77 master replies by selecting the station button that is lit. At the door
station, when selected, a pretone is heard, unless it is muted at the
TB-AD1, 10 adaptor.
“Transfer”
allows
two
TB-SE
subs
to
communicate
with
each
other
When a master receives a call from sub A, requesting transfer of
call, TB-M leaves sub A waiting, pressing a sub B select button.
When sub B picks up the call (sub A hears a busy tone), TB-M
depresses Transfer switch.
TB-M then reselects waiting sub A with red LED on. Three parties
i, are on the line, and TB-M may hang up.
Transfer switch & LED J * Door-to-master or master-to-master calls are not transferrable.
| x If transfer LED is lit when a transfer is not being made, it can be
cleared by pressing “transfer” switch.
ed:
Oe

eed
ey
g
TB-M
places
a
buzzer-activating
call
to
a
TB-SE
sub
Buzzer
sounds
continuously
at
TB-SE
sub,
in
addition
to
ordinary
tremolo.
Pick
up
on
the
TB-SE
station,
that
the
buzzer
is
connected
to.
Adjusting receive and call tone volume
E TB-M dual-master system
E TB-SE sub operation
be tia
H n la
Ej ij
roi el |
| Z
ee ee | .
Booted
\ $ 1] i
S
TECHNICAL PRECAUTIONS
| | = — Speaker
for call tone
a
Upper
control
adjusts
handset
receiver
volume,
CD
when
TB-M
does
not
hear
a
TB-SE
sub
clearly.
Call
tone
a 2a
Tone
control
adjusts
ringing
tremolo,
3
levels.
3-levels each
TB-M 2
LAGO]
Ü
-------- --- eee. |
Two
masters
call
and
communicate
with
each
assigned
select
button.
Transfer
of
a
sub’s
call
to
another
on
the
other
master
is
not
possible.
A
call
from
TB-SE
subs
that
are
connected
to
two
masters
activates
tremolo
tone
at
both
masters.
When
the
controlling
TB-M
is
busy,
the
other
TB-M
may
pick
up.
In
this
case,
the
sub
hears
both
tremolo
and
busy
tones.
7
*
Dual-master
has
an
operation
that,
when
TB-M1
places
a
call
to
either
TB-M2
or
a
common
TB-SE
that
is
already
in
communication,
the
talk
line
is
connected
among
3
parties.
It
reduces
communication
volume.
One
party
should
hang
up
to
restore
normal
volume.
To
call
TB-M
master,
simply
pick
up
and
it
rings
TB-M
with
tremolo
tone,
which
continues
ringing
until
the
call
is
answered.
Intermittent
tone
means
the
master
is
occupied.
Hang
up
or
continue
to
hold.
When
called
by
tremolo
tone,
simply
pick
up.
*
The
power
switch
is
located
on
back
panel
of
TB-M
console,
which
should
be
placed
ON,
except
for
special
occasions.
may
reset
itself.
Possible
causes
are;
power
supply
is
unplugged,
connecting
wires
are
loosened
or
shorted.
Do
not
attempt
to
open
TB-M
equipment
nor
change
wiring.
Ask
qualified
personnel.
If
the
system
malfunctions,
turn
off
and
on
TB-M
master,
by
which
the
system
*
At
end
of
each
communication,
be
sure
to
place
handset
in
cradle
properly.
If
not,
TB-M
master
or
TB-SE
sub
will
not
hear
the
call
tone.
*
The
TB-M
is
rated
to
operate
at
temperatures
between
0°C
~
+40°C
(32°F
~
104°F).
*
Clean
the
TB-M
equipment
with
a
soft
cloth
dampened
with
neutral
household
cleanser.
Never
use
any abrasive cleaner or cloth.
on

Power source
Power consumption
Capacity
Calling
Communication
Wiring
Wiring distance
Compatibility
© SPECIFICATIONS
DC18V, 350mA max. or AC 15 — 16V, 50/60Hz. 750mA max.
6W max. 3W (standby)
60 stations max., TB-SE or door stations incl.
One add-on selector TB-20G or TB-40G per TB-M. 1 to 3 TB-AD1 door adaptors or one
TB-AD10 only alternatively, or one TB-ADM10 only.
TB-SE sub’s call-in is annunciated with intermittent tremolo tone and LED, lighting in red,
both of which are held (approx. 40 seconds for IE/IF door stations).
Station-select button calls each TB-SE with intermittent tone. Corresponding LED is lit to indicate
which sub is called. Master can call IE/IF door station by voice, with or without pretone (selectable).
Both stations communicate simultaneously via handset.
2 conductors (parallel) or a pair in multi-cond. cable TB-M to ea. TB-SE
5 conductors TB-M to TB-AD1
14 conductors max TB-M to TB-AD10
3 conductors between TB-M’s
* In TB-M dual-master system, two parallel conductors cables are required for each common TB-SE
sub.
ooo o o oo oomme | omme | omm || 22AWG | 2OAWG | 18AWG |
emote | 40m | 600m | 900m || 1300 | 2000 | 3.000 _
TIBMtoTB:M | 200m | 300m | 480m || 650 | 1000 | 1,570 |
TB-M to TB-AD1
65m 100 150m 210’ 330’ 495’
TB-AD1(10) to IE/IF door 150m 230m 360m 500’ 750’ 1,200’
Dimensions & weight
Model
TB-10M
TB-20M
TB-20G
TB-40G
TB-AD10
TB-AD1
>
Aiphone.
LEEEEEEE EEE EEE SEES
Height
117 mm
117 mm
97 mm
97mm
97 mm
140 mm
Aiphone Co., Ltd., Nagoya, Japan
Aiphone Corporation, Believue, WA, USA
TB-M-I(E)O396F
TB-M system components: TB-(10,20)M, TB-(20,40)G & TB-AD(1,10), cannot be intermixed
with TB-(10,20)T masters, while TB-RC handset sub can be used with TB-M system.
Width Depth Height Width Depth Weight
255mm x 230mm 4-5/8" x 10" x 9" 1.8 kg (3.97 Ibs.) |
330 mm x 230 mm 4-5/8" x 13" x 9" 2.3 kg (5.07 Ibs.
150mm x 230 mm 3-13/16" x 6" x 9" 1.0 kg (2.20 Ibs.) |
300 mm x 230mm 3-13/16" x 11-13/16" x 9" 1.9 kg (4.19 Ibs.)
150 mm x 230mm 3-13/16" x 6" x 9" 1.1 kg (2.43 Ibs.)
74mm x 42mm 5-1/2" x 3" x 1-5/8" 160 g (0.35 Ibs.)
ae eee
Aiphone will not be responsible for any costs incurred involving on site service calls.
she oje eje efe ole eje efe efe efo oje sfe efe efe ole ofe oft fe oje ofe -fe efe oje ole efe ele sjo ofe ole efo ole sje efe efo sfe ofe fs ole of eje ole ejo eje efe ole ofe oft ofe ofe ote ole ele of ole ole efe ole efe ote ole ale ole
GA
Sn sa aA a A ce i Se a A
WARRANTY
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a
period of one year after delivery to the ultimate user and will repair free of charge or replace at no charge, should it
become defective upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself
the sole right to make the final decision whether there is a defect in materials and/or workmanship; and whether or not the
product is within the warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in
violation of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This
warranty does not cover batteries or damage caused by batteries used in connection with the product.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by
PEEEEEEE PEE EES EES
COMMUNICATION SYSTEMS
HOME, BUSINESS,
ONE
INDUSTRY.
Printed in Japan (E)