SpectraLink MOG400 User manual

Link 150 M3 MCU
Facility Preparation
Link Wireless Telephone System
Part Number: 72-0075-05
Issue F

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
Notice
SpectraLink Corporation has prepared this document for use by SpectraLink personnel and customers. The
drawings and specifications contained herein are the property of SpectraLink and shall be neither reproduced in
whole or in part without the prior written approval of SpectraLink, nor be implied to grant any license to make,
use, or sell equipment manufactured in accordance herewith.
SpectraLink reserves the right to make changes in specifications and other information contained in this
document without prior notice, and the reader should in all cases consult SpectraLink to determine whether
any such changes have been made.
The terms and conditions governing the sale of SpectraLink hardware products and the licensing of
SpectraLink software consist solely of those set forth in the written contracts between SpectraLink and its
customers. No representation or other affirmation of fact contained in this document including but not limited
to statements regarding capacity, response-time performance, suitability for use, or performance of products
described herein shall be deemed to be a warranty by SpectraLink for any purpose, or give rise to any liability of
SpectraLink whatsoever.
In no event shall SpectraLink be liable for any incidental, indirect, special, or consequential damages
whatsoever (including but not limited to lost profits) arising out of or related to this document, or the
information contained in it, even if SpectraLink has been advised, knew, or should have known of the
possibility of such damages.
Trademark Information
SpectraLink
The SpectraLink logo
LinkPlus
Link
NetLink
SVP
Are trademarks and registered trademarks of SpectraLink Corporation.
All other trademarks used herein are the property of their respective owners.
SpectraLink Corporation
5755 Central Avenue
Boulder, CO 80301
303 440 5330 or
800 676 5465
www.spectralink.com
Copyright © 1998 to 2006 SpectraLink Corporation. All rights reserved
Information in this document is subject to change without notice and does not represent a commitment on the
part of SpectraLink Corporation. The software described in this document is furnished under a license and/or
copyright and may only be used with the terms of SpectraLink’s software license agreement as found in this
manual or at http://www.spectralink.com/consumer/resources/software_updates.jsp. The software may be
used only in accordance with the terms of the agreement. No part of this manual, or the software described
herein, may be reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopying and recording, for any purpose except for the sole intent to operate the product or without the
express written permission of SpectraLink Corporation.
PN: 72-0075-05-F.doc Page 2

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
WARNING: Changes or modifications to this equipment not approved by SpectraLink
Corporation may cause this equipment to not comply with part 15 of the FCC rules and
void the user’s authority to operate this equipment.
WARNING: SpectraLink products contain no user-serviceable parts inside. Refer servicing
to qualified service personnel.
IMPORTANT SAFETY INFORMATION
Follow these general precautions while installing telephone equipment:
•Never install telephone wiring during a lightning storm.
•Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.
•Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface.
•Use caution when installing or modifying telephone lines
•When installing Base Stations outside or in buildings other than the one containing the
System Controller, take the following precaution:
If wiring for a Base Station exits a building—whether to reach an outdoor Base
Station location or to reach a Base Station in another building—the wiring must be
protected at both ends by a Quick Clip Fuse from Illinois Tool Works, Linx Div
model number SCP-2X2. The Quick Clip Fuse replaces the bridging clips on the 66
blocks for all four connections to the non-internal Ba
ision,
se Station.
PN: 72-0075-05-F.doc Page 3

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
Table of Contents
1. About This Document 5
1.1 SpectraLink Corporation Model Numbers 5
1.2 Related Documents 5
1.3 Customer Support Hotline 5
1.4 Icons and Conventions 5
2. Link Wireless Telephone System Overview 6
2.1 System Operation 6
2.2 The Front Panel of the MCU 8
3. Site Preparation 9
3.1 Installation Steps 10
3.2 Materials Required by Customer 11
3.3 Determine Location of MCU 11
4. Run Cable for System 12
4.1 Run Cables to Base Station Locations 12
4.2 Pull Cable 13
4.3 Terminate Cable at Base Station Locations 13
4.4 Prepare Demarc Blocks 14
4.5 Install Demarc Blocks 18
4.6 Assign and Program Ports 18
4.7 Connect Cables from Base Stations and Phone Lines to Demarc Blocks 19
5. Install Base Stations 23
5.1 Mount Base Stations on Dropped Tile Ceilings 23
5.2 Mount Base Stations On Finished Ceilings 24
5.3 Install Outdoor Base Stations 25
6. Sample Schedule for Installation 26
7. Link Wireless Telephone Planning Worksheet 27
8. Base Station Location Worksheet 28
PN: 72-0075-05-F.doc Page 4

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
1. About This Document
This document describes the installation procedure for the Link Wireless Telephone
System (Link WTS) with a Link 150 M3 Master Control Unit (MCU). The
procedures described in this manual are those that take place
after the installation-
planning procedure. You should already know the equipment requirements and
installation locations. For example, you should know where each Base Station and
the MCU will be installed.
1.1 SpectraLink Corporation Model Numbers
This document covers the following registered model numbers:
SCA416, SCA408, SCA516, SCC408, SCC416, SCD408, SCD416, SCE408, SCE416,
SCF4089, SCF416, SCI408, SCI416, SCJ408, SCJ416, SCK408, SCK416, SCL408,
SCL416, SCM408, SCM416, SCN408, SCN416, SCO408, SCO416, SCS416,
SCT416, SCX416 RCC400, RCO400, RCU100, RCU200, RCU201, MOG400
1.2 Related Documents
Link 150 M3 MCU: Installation and Operation (72-0075-01)
Link 150 M3 MCU: Quick Reference (72-0075-02)
Link 150 M3 MCU: Open Application Interface (OAI) Gateway Installation and
Setup (72-0075-07)
Installing the Outdoor Base Station (72-0050-01)
Available at http://www.spectralink.com/consumer/resources/manuals.jsp.
LinkPlus Interface Guide (72-0171-xx where xx indicates a number corresponding to
the type of PBX)
Available at http://www.spectralink.com/consumer/resources/interface_guides.jsp.
1.3 Customer Support Hotline
SpectraLink wants you to have a successful installation. If you have questions please
contact the Customer Support Hotline at [phone].The hotline is open
Monday through Friday, 6 a.m. to 6 p.m. Mountain time.
1.4 Icons and Conventions
This manual uses the following icons and conventions.
Caution! Follow these instructions carefully to avoid danger.
Note these instructions carefully.
NORM This typeface indicates a key, label, or button on the MCU or Link
Wireless Telephone (handset).
PN: 72-0075-05-F.doc Page 5

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
2. Link Wireless Telephone System Overview
Review this section if you are unfamiliar with the features and operation of the Link
150 M3 MCU.
2.1 System Operation
The Link WTS is a wireless communication system that offers direct telephone
access for incoming and outgoing calls anywhere within a facility.
The Link WTS consists of three basic components: the Master Control Unit, the
Base Station, and the Wireless Telephone, or handset. This diagram shows an
overview of system. Components are described below.
M
aste
r
Control
U
ni
t
Link
Wireless
Telephones
B
ase
Stations
Analog or
Digital
Interface
PBX
Application
Server
OAI
Gateway
The Link Wireless Telephone System
Master Control Unit (MCU)
Serves as the connecting point, or gateway, between the Base Stations and the
existing telephone system. One or more of these boxes (approximately 12” x 3” x 7”)
are typically installed in the telephone equipment room and provide connectivity
from the telephone system to the Link WTS. Each MCU is hard-wired to one or
more Base Stations, which in turn provides the wireless link to each of the handsets.
The MCU establishes the connection from the telephone line to the appropriate Base
Station in order to reach a handset.
The MCU supports four Base Stations and up to 16 handsets. Up to four Link 150
M3 MCUs can be linked together for extended coverage area. Chained MCUs
support up to 64 handsets maximum.
PN: 72-0075-05-F.doc Page 6

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
SpectraLink offers an analog MCU that works with telephone systems (CO, PBX or
key systems) with analog (loop start) ports. SpectraLink also offers digital MCUs that
work with the most common brands of telephone systems (PBX or key systems)
digital ports.
Base Stations
Act as a radio transceiver to provide the communications signal between the handset
and the MCU. Base Stations are slightly larger than a smoke detector and are
typically mounted on the ceiling, in strategic locations throughout the facility. A
single Base Station can provide radio coverage for an area of 5,000 to 50,000 square
feet depending on building obstructions. Base Stations may be located up to 2,200
cable feet from the MCU.
When a handset user makes or receives a call, the handset and Base Station establish
a digital radio communication link. As the user moves throughout the coverage area,
calls are “handed off” to the Base Station that is able to provide the best radio signal
(typically the closest Base Station). These handoffs involve the handset establishing a
communication link with another Base Station and dropping the previous link.
Link Wireless Telephones
Communicate with the Base Station using digital spread spectrum transmission at
902-928 MHz. Employees can carry handsets to keep in contact as they move
throughout the building. The handsets use on-premises wireless technology; they are
not cellular or satellite phones. They are connected to the facility’s existing telephone
system and, just like wired telephones, can receive calls directly, receive transferred
calls, transfer calls to other extensions and make outside and long-distance calls
(subject to the restrictions applied in the facility.)
PN: 72-0075-05-F.doc Page 7

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
2.2 The Front Panel of the MCU
The MCU’s front panel contains the connections to the telephone system, switches
to control system administration, and status LEDs.
1. STEP Button: Selects a specific line or Base
Station during registration process.
2. Mode Switch: Selects the mode of operation for
the Link 150 M3 MCU.
ADMIN: Administration mode, used to set up
system features to match features on the
telephone system.
NORMAL: Normal mode, used during day-to-day
operations.
REGISTER: Registration mode, used to add or
delete handsets and Base Stations.
3. DEL/ENTER Button: Removes a registered
handset from the system.
4. IPC IN Port: Used to connect preceding MCUs in
a multi-MCU configuration.
5. IPC OUT Port: Used to connect sequential MCUs
in a multi-MCU configuration or to connect to an
Open Applications Interface (OAI) Telephony
Gateway.
6. ERROR LED: Flashes when the system has
detected an error. When flashing, check the STATUS
LEDs for an error code.
7. STATUS LEDs: Indicate system error messages
and status. See
Link 150 M3 MCU: Installation and
Operation
for more information.
8. LINE LEDs: Indicate the line status of each
handset: ringing, in-use or not active.
9. BASE STN LEDs: Indicate the status of each Base
Station.
10. CONN Aor B: RJ-21 connector to the cross-
connect demarc block. Connector B is supplied and
used only with four-wire digital interface.
11. Power Jack: Connects to the AC adapter to
supply power to the system.
CAUTION: Use only the provided Class II AC
Adapter with output 24VDC, 1A.
12. Grounding Lug:For use on the analog interface
MCU (SCA-5XX).
PN: 72-0075-05-F.doc Page 8

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
3. Site Preparation
All site preparation steps should be completed prior to the arrival of the SpectraLink
field service engineer. A SpectraLink customer support representative will contact
the customer the week before the scheduled installation date to confirm that pre-
installation tasks have been completed. Upon confirmation, a SpectraLink field
service engineer will travel to the site to complete the system installation and train
the system administrator and handset users.
If upon arrival the SpectraLink field service engineer determines that the pre-
installation work has not been completed correctly, the engineer can: 1) leave the site
and reschedule the installation when the action items have been completed or
corrected, or 2) assist in preparing the site, and thus spend additional time in the
installation of the system. Because of the additional cost incurred by SpectraLink in
executing either option, the customer will be billed for the additional time at the
standard hourly rate plus expenses.
MCU location prepared. Typically the MCU is installed in the telephone
equipment room. This location must have sufficient backboard space. See
section 3.3
Determine Location of MCU for more information.
The correct number of cross-connect blocks (or equivalent) are installed and
connected to a 25-pair telco wire terminated with an RJ-21 male connector at the
MCU location. See section 4.4
Prepare Demarc Blocks for more information.
A two-pair cable to each Base Station as designated on the building floor plans.
See section 4.1
Run Cables to Base Station Locations for more information.
The Base Station wire is terminated at the appropriate cross-connect demarc
blocks as shown in sections 4.4
Prepare Demarc Block s and 4.7 Connect Cables
from Base Stations and Phone Lines to Demarc Blocks .
The Base Station wiring is terminated with RJ-45 crimp-on plugs at the
designated Base Station locations. See section 4.3
Terminate Cables at Base
Station Locations for more information.
The analog or digital-phone extensions from the phone system are terminated at
the appropriate cross-connect demarc block and the block is labeled. See section
4.7
Connect Cables from Base Stations and Phone Lines to Demarc Blocks .
A dedicated dial line is available for the diagnostic modem.
A system administrator is designated for the Link WTS. This person should be
present for the installation. The SpectraLink field service engineer will provide
system training to the system administrator on the day following the installation.
When this checklist is completed please sign, date, and fax to:
Install Coordination 303-449-7016
Signature: ___________________________________ Date: ________________
PN: 72-0075-05-F.doc Page 9

SpectraLink Corporation Facility Preparation
Link WTS – Link 150 M3 MCU
3.1 Installation Steps
This table lists the installation steps and the person usually responsible for each step.
9Task
Description
Wire
Contractor or
Electrician
Field Service
Engineer
Customer
Project Mgr/
Sys Admin
Site Preparation
Determine location of MCU 9
Run Cable for System
Run cable to Base Station locations 9
Terminate cable at Base Station locations 9
Prepare and install demarc blocks 9
Assign and program ports 9
Connect cables to demarc blocks 9
Install Link WTS
Survey site and check components 9
Install MCUs 9
Install Base Stations 9
Install Outdoor Base Stations 9
Connect and register handsets 9
Set up diagnostic modem 9
Register handsets 9
Program handset features 9
Test handsets 9
Site certification 9
PN: 72-0075-05-F.doc Page 10