Airwell KN-24SH Operating instructions

OWNER'S MANUAL
INSTALLATION MANUAL
AIR CONDITIONER
Please read this owner's manual carefully before using the air conditioner
and reserve this manual in case of further reference.
K INST. MENU

CONTENTS
INSTALLATION...................................................................................................... 1
REQUIREMENT FOR ELECTRIC SAFETY.......................................................... 2
PARTS NAMES AND THEIR FUNCTION........................................................... 3
OPERATION ATTENTION.................................................................................... 4
TEMPORARY OPERATIONS............................................................................... 5
ADJUSTING AIR FLOW DIRECTION.................................................................... 5
HINTS FOR ECONOMICAL OPERATION............................................................. 6
MAINTENANCE..................................................................................................... 6
PHENOMENA NOT CONCERNING MALFUNCTIONS...................................... 8
TROUBLES AND CAUSES (concerning the unit).................................................. 9
TROUBLES AND CAUSES (concerning the remote control))................................ 9
PREPARATION .................................................................................................... 10
K INST. MENU

5
5
6
6
8
9
9
ADJUSTING AIR FLOW DIRECTION
10
1
POWER
LOCATION
INSTALLATION
K INST. MENU

2
CAUTION
3
c
KN-27SH
operation lamp
timer indicator
heat indicator
power supply indicator
K INST. MENU

2
CAUTION
3
c
KN-27SH
operation lamp
timer indicator
heat indicator
power supply indicator
K INST. MENU

4
NOTICE!
only cooling model (without heating operation)
K INST. MENU

TEMPORARY OPERATIONS
5
ADJUSTING AIR FLOW DIRECTION
are exhausted.two modes including mandatory HEAT
and mandatory COOL can be selected through the
TEMPORARY BUTTON on the air inlet grill control box
of the indoor unit Once you push this button,the air
conditioner will run in such order mandatory HEAT
mandatory COOL,OFF,and back to mandatory HEAT.
mandatory HEAT
HEAT
K INST. MENU

6
HINTS FOR ECONOMICAL OPERATION
MAINTENANCE
CAUTION
METHOD FOR CLEANING AIR FILTER
K INST. MENU

7
MAINTENANCE
CLEANING THE AIR OUTLET AND THE PANEL
CAUTIONS
MAINTENANCE
IF YOU DO NOT PLAN TO USE THE UNIT FOR A LONG TIME
THE MAINTENANCE OF THE OUTDOOR UNIT
K INST. MENU

8
8
RESTART AFTER A LONG TIME
PHENOMENA NOT CONCERNING MALFUNCTIONS
Fox each Mode including Power OFF and SB,a Min time delay of 3min before Comp.restarting,
excluding Deicing Mode.
K INST. MENU

9
K INST. MENU

PREPARATION
10
K INST. MENU

INSTALLATION MANUAL
For correct installation,read this manual before starting installation.
This manual may be subject to change without notice for purpose of improvement.
K INST. MENU

CONTENTS
1. PRECAUTIONS...................................................................................1
2. INSTALLATION INFORMATION..........................................................2
3. ATTACHED FITTINGS.........................................................................3
4. INSTALLATION PLACE.......................................................................4
5. INDOOR UNIT INSTALLATION...........................................................5
6. OUTDOOR UNIT INSTALLATION.......................................................8
7. INSTALL THE CONNECTING PIPE....................................................9
8. CONNECT THE DRAIN PIPE............................................................13
9. WIRING..............................................................................................15
10. TEST OPERATION..........................................................................19
PAGE
K INST. MENU

1
PRECAUTIONSPRECAUTIONS
SAFETY CONSIDERATIONS
Installation and servicing of air conditioning equipment can be hazardous due to system pressure and electric
components. Only trained and qualified service personnel should install, repair or service air conditioning
equipment.
All other operations should be performed by trained service personnel. When working on air conditioning
equipment, observe precautions in the literature, tags and labels attached to the unit and other safety
precautions that may apply. Follow all safety codes. Wear glasses and work gloves. Use quenching cloth for
brazing and unbrazing operations. There are fire extinguishers available for all brazing operations.
This manual describes the installation of specified indoor units. Do not install them connected with any other
indoor and outdoor unit. Mismatching of units and incompatibility between control devices in the two units could
lead to damage of both units.
Before performing service or maintenance operations on system, turn off main power switch of the unit.
Electrical shock could cause personal injury.
This unit shall be installed in accordance with national wiring regulations.
If the supply cord is damaged, it must be replaced by the manufacture or its service agent or similarly qualified
person in order to avoid a hazard.
The means for disconnection from the supply having a contact separation of at least 3 mm in all poles.
1. Wire the outdoor unit, then wire the indoor unit. You are not allowed to connect the air conditioner with the
power source until wiring and piping the air conditioner is done.
2. For installation of the indoor unit, outdoor unit, and connection piping in between, follow the instructions given in
this manual as strictly as possible.
3. Installation in the following places may cause trouble. If it is unavoidable, please consult with the dealer.
(1) A place full of machine oil.
(2) A saline place such as coast.
(3) Hot-spring resort.
(4) A place full of sulfide gas.
(5) A place where there are high frequency machines such as wireless installation, welding machine, medical
facilities.
(6) A place of special environmental conditions.
&&
&&
&&&&
WARNING
WARNING
WARNING
CAUTION
K INST. MENU

2
NOTENOTE
INSTALLATION INFORMATION
Remark per EMC Directive 89/336/EEC
CAUTION
To prevent flicker impressions during the start of the compressor (technical process), following
Never put the remote controller at the place with humid or direct sunlight, or near heaters.&Please keep the remote controller more than 1m away from TV or stereo set.&the indoor unit.
Please use the remote controller within the allowed distance, and keep the transmitter toward the receiver of&Please do not throw the remote controller or beat it.&
TION ORDERINSTALLA TION ORDERINSTALLA
est operation.7. T
6. Wiring;
5. Connect the drain pipe;
installation conditions do apply.
4. Install the connecting pipe;
&
3. Install the outdoor unit;
2. Install the indoor unit;
1. Select the location;
CAUTIONS FOR THE REMOTE CONTROLLER OPERATIONCAUTIONS FOR THE REMOTE CONTROLLER OPERATION
5.
4.
3.
2.
1.
For any question contact your local dealer.
For power details of the air conditioner refer to the rating plate of the product.
for products like washing machines, air conditioners or electrical ovens.
For detailed installation acceptance please refer to your contract with the power supplier, if restrictions to apply
No other equipment has to be connected with this power line.
has to be of a low impedance, normally the required impedance reaches at a 32 A fusing point.
The power connection for the air conditioner has to be done at the main power distribution. The distribution
To install properly
When all the installation work is finished, please turn on the power only after a thorough check.&When installing the indoor unit or its tubing, please follow this manual as strictly as possible.&The air conditioner must be installed by qualified persons.& , please read this "installation manual" at first.
CAUTIONS FOR THE REMOTE CONTROLLER OPERATION
INSTALLATION ORDER
K INST. MENU

use,please restorethemcarefully.
Please check whether the following fittings are of full scope. If there are s ome attached fitting free from
9. Seal ring ................................................1
8. Drain elbow .............................................1
7. Tightening band .......................................20
6. Out-let pipe clasp ........................................1
4. Bolt M6x12
5. Out-let pipe sheath ......................................1
DrainpipeFittings
...............................................4
11. Wall conduit cover ..................................1
10. Wall conduit ..........................................1
ProtectPipeFittings
...............................13. Installation pape board
.........................................4
13. Frame ................................................. 1
12 . Remote controller ................................... 1
Remotecontroller&ItsFrame
15. Alkaline dry batteries (AM4) ........................ 2
10-C-H)................ 214. Mounting screw (ST2.9
2. Installation hook
.........................................4
3
..............................1set
(only KN30/36/45)
..............................1
..............................1
20. one-way valve throttle
19. Rcw installation manual
18. Rcw operating manual
17. Installation manual ....................................1
16. Owner's manual .................................1
Others
1. Expansible hook
InstallationFittings
ATTACHED FITTINGS
K INST. MENU

4
INSTALLATION PLACEINSTALLATION PLACE
Location in the following places may cause malfunction of the machine. (If unavoidable, please consult
your local dealer)
a. There is petrolatum existing.
b. There is salty air surrounding (near the coast).
c. There is caustic gas (the sulfide, for example) existing in the air (near a hot spring).
d. The Volt vibrates violently (in the factories).
e. In buses or cabinets.
f. In kitchen where it is full of oil gas.
g. There is strong electromagnetic wave existing.
h. There are inflammable materials or gas.
i. There is acid or alkaline liquid evaporating.
j. Other special conditions.
Select the correct carry-in path.
Move this unit as originally packaged as possible.
If the air conditioner is installed on a metal part of the building, it must be electrically insulated according to the
relevant standards to electrical appliances.
CAUTIONSCAUTIONS
NOTICES BEFORE INSTALLATIONNOTICES BEFORE INSTALLATION
1.
2.
3.
2. The outdoor unit
1. The indoor unit
There is enough room for installation and maintenance.
The ceiling is horizontal, and its structure can endure the weight of the indoor unit.
The air outlet and the air inlet are not impeded, and the influence of external air is the least.
The air flow can reach throughout the room.
The connecting pipe and drainpipe could be extracted out easily.
There is no direct radiation from heaters.
There is enough room for installation and maintenance.
The air outlet and the air inlet are not impeded, and can mot be reached by strong wind.
It must be a dry and well ventilating place.
The support is flat and horizontal and can stand the weight of the outdoor unit. And will no additional noise or
vibration.
Your neighborhood will not feel uncomfortable with the noise or expelled air.
There is no leakage of combustible air.
It is easy to install the connecting pipe or cables.
Determine the air outlet direction where the discharged air is not blocked.
A place free of a leakage of combustible gases.
In the case that the installation place is exposed to a strong wind such as a seaside or high position, secure
the normal fan operation by putting the unit lengthwise along the wall or using a duct or shield plates.
If possible, do not install the unit where it is exposed to direct sunlight.
If necessary, install a blind that does not interfere with the air flow.
During the heating mode, the water drained off the outdoor unit. The condensate should be well drained away
by the drain hole to an appropriate place, so as not to interfere other people or public.
Select the position where it will not be subject to snow drifts, accumulation of leaves or other seasonal debris.
It is important that air flow for the outdoor unit is not impeded as this will result in reduction in heating or
cooling performance.
K INST. MENU

5
INDOOR UNIT INSTALLATION
1. Install the main body
A. The existing ceiling (to be horizontal)
Please cut a quadrangular hole of 880X880mm in the ceiling according to the shape of the installation paper
board.(Refer to Chart3,4)
The center of the hole should be at the same position of that of the air conditioner body.
Determine the lengths and outlets of the connecting pipe, drainpipe and cables.
To balance the ceiling and to avoid vibration, please enforce the ceiling when necessary.
b. Please select the position of installation hooks according to the hook holes in the installation board.
a.
Drill four holes of M12mm, 45~50mm deep at the selected positions on the ceiling. Then embed the expansible
hooks (fittings).
Face the concave side of the installation hooks toward the expansible hooks. Determine the length of the
installation hooks from the height of ceiling, then cut off the unnecessary part.
c. Please adjust the hexangular nuts on the four installation hooks evenly, to ensure the balance of the body.
The length could be calculated from Chart5:
Length=H-181+L (in general, L=100mm and is half of the whole length of the installation hook)
If the drainpipe is awry, leakage will be caused by the malfunction of the water-level switch.
Adjust the position to ensure the gaps between the body and the four sides of ceiling are even. The body's
lower part should sink into the ceiling for 10~12mm (Refer to chart 5).
Locate the air conditioner firmly by wrenching the nuts after having adjusted the body's position well.
Necessary room
$2500mm
outlet
inlet
outlet
Note: 27 Series A/260mm
30/45 Series A/330mm
A
ground
Chart 1
Drain side Tubing side
A
780 (Hook-location)
840 (Body)
880 (Ceiling hole)
950 (Panel)
(Unit: mm)
780 (Hook-location)
840 (Body)
880 (Ceiling hole)
950 (Panel)
Chart 3
Chart 2
$1000mm
$1000mm
$1000mm
$1000mm
K INST. MENU

6
Grid switch
B. New built houses and ceilings
Body
Nut
Ceiling 880mm
A
Hook
panel
B
Central hole
Body M6X12 Installation paper board
Body
Chart 4
Chart 5 Chart 6
Chart 7
Note: 27 Series B=240mm
30/45 Series B=310mm
Ceiling
Body
34mm
10~12mm
136mm
L
In the case of new built house, the hook can be embedded in advance (refer to the A. B mentioned above ).
But it should be strong enough to bear the indoor unit and will not become loose because of concrete shrinking.
After installing the body, please fasten the installation paper board onto the air conditioner with bolts (M6X12 )
to determine in advance the sizes and positions of the hole opening on ceiling.
Refer to the A. c mentioned above for installation.
Remove the installation paper board.
Please first guarantee the flatness and horizontal of ceiling when installing it.
Refer to the A. a mentioned above for others.
a.
b.
c.
d.
CAUTIONSCAUTIONS
After completion of installing the body, the four bolts (M6X12) must be fastened to the air conditioner to ensure
the body is grounded well.
Never put the panel face down on floor or against the wall, or on bulgy objects.
Never crash or strike it.
(1)Remove the inlet grid .
a. Slide two grid switches toward the middle at the same time, and then pull them up. (Refer to chart 8)
O
b. Draw the grid up to an angle of about 45 , and remove it.(Refer to chart 9)
(2)Remove the installation covers at the four corners.
Wrench off the bolts, loose the rope of the installation covers, and remove them. (Refer to chart 10)
2. Install The Panel
CAUTIONSCAUTIONS
Chart 8 Chart9 Chart 10
H (Ceiling height)
K INST. MENU