Akai DV-R6000DSS User manual

SERVICE MANUAL
Model:
DVR6000DSS
DVD HOME THEATER SYSTEM
www.akai.ru

Title Page
1. CONTENTS
2. BLOCK DIAGRAM (CABLE CONNECTIONS)
3. POWER SUPPLY
4. FUNCTIONAL DESCRITPIONS
4.1 DVD MPEG board
4.2 Front Panel
4.3 SMPS
4.4 DVD Driver
5. DESCRIPTION OF THE INTEGRATED CIRCUITS
5.1 SWPS TRANSFORMER
5.2 FRONT PANEL DRIVER IC FRO VIR (PT6311)
5.3 SWPS CONTROLLER IC (5M02659)
5.4 SWPS PROGAMMABLE SHUNT RE
GULATOR (FAIRCHILD TL 431)
5.5 LINE FILTER(2 x 6.8mH)
2
3
4
1
4
10
10
12
13
13
14
18
22
23
1
1.CONTENTS
1

2 BLOCK DIAGRAM(CABLE CONNECTIONS)
DVD Service Manual
1
2

1
DVD Service Manual
3

MT1389DE/C
16M
FLADH
64M
SDRAM
SEIAL
EPROM
AM/FM
TUNER
AUD2
AUD1
CVBS
R
G
B
DAC
WMA8722
AUD0 4053
SURROUND L/R
FRONT L/R
L/R
KARAOKE
DOUT CENTRE/SUBWOOF
4.FUNCTIONAL DESCRIPTIONS
4.1DVD MPEG board
1
DVD Service Manual
4

1
DVD Service Manual
5

erefore
.
.
.
.
.
1
DVD Service Manual
6

DVD Service Manual
7

1
DVD Service Manual
8

1
DVD Service Manual
9

E6202 CS1694
There are 1 device operated by the or (Optional):
4.3 SMPS
The mains power(220VAC) fed from K1is filtered through 3C1, 3L1, 3C2 then rectified by D1,D2, D3 and
D4 and generates an output at 300VDC. This 300VDC fed to 3TR1 (pin1, pin5) which
connects to 5M02659R(pin3), then 5M02659R will automatically generate a 50KHz square waveform,
this 50KHz square waveform controls the ON/OFF between 5M02659R pin1 and the ground.
In normal condition, T1 primary (between pin2 and pin4) will create a 50KHz square waveform
which is controlled by 5M02659R, this signal then fed to 3TR1 and generates 2 different potential
voltages of 12V and 5V .The 12VDC and 5VDC
then rectified by3D11 and then filtered by3 L2, 3R9, 3C18, 3CC25 and 3C11. The feedback voltage
is controlled by Ic3 TL431 and IC2 PC817. When the output voltage is higher than 5V, the voltage at
TL431(2.5V) is compared with R10 and send out a signal to 5M02659R, the output square waveform then
will change to adjust the output voltage, this acts as a voltage stabilizer.
1
4.2.1 Front Panel Interface
6 Pin, Data Connector Pin Assignments
PIN NAME I/O DESCRIPTION
1 DATA I IR sensor interrupt
2 CLK O Front Panel chip select
3 STB O Front Panel clock
4 GND O Front Panel Data output
5 VCC
6 REM I Front Panel Data input
DVD Service Manual
10

1
DVD Service Manual
11

1
DVD Service Manual
12

1
5. DESCRIPTION OF THE INTEGRATED CIRCUITS
5.1 SMPS TRANSFORMER
1. GENERAL INFORMATION
Main Voltage Operations:
Main Drop-out Voltage:
Mains STart-up Voltage:
Operating Frequency:
90Vac - 265 Vac
Max. 90 Vac
Max. 90 Vac
60 KHz
2. ELECTRICAL CHARACTERISTICS
WINDING
PrimaryInductance
PIN.NO
2-4
INDUCTANCE 6DESCRIPTION
1.5mH10% <0.50W
1. Primary Leakage inductance (Pin 2-4) L1.5mH
2.2 WITHSTANDING VOLTAGE
The transformer shall sithstanding a voltage of 4 Kvms for 1 minute and 1 mA between
primary and seconday winding and also 2 Kvms for 1 minute and 1 mA between
primary winding with core and secondary winding with core.
2.3 INSULATION RESISTANCE
The insulation resistance shall be ore than 500M between primary and seconday
windings when the applied voltage 300 Vdc for 1 minute
2.4 ELECTRICAL CHARACTERISTICS
1. Before taking measurement Pp01 will be to give 5.0Vdc on 5.0Vdc line at Minimum
setting of controls and a mains voltage 220 Vac.
2. Before taking a measurement, DVD set should be working at least 5 minutes on
Normal condition
2.1 STATIC CHARACTERISTICS
DVD Service Manual
13

1
DVD Service Manual
5.2 FRONT PANEL DRIVER IC FOR VIR (PT6311)
5.2.1 General Description
14

1
DVD Service Manual
15

DVD Service Manual
1
16

1
DVD Service Manual
17

1
DVD Service Manual
5.3 SWPS CONTROLLER IC ( )5M02659
18

1
DVD Service Manual
19