Alcatel-Lucent AOS-W Instant User manual

AOS-W Instant
6.2.1.0-3.4
Quick Start Guide
This Quick Start Guide assists you to quickly connect and configure AOS-W
Instant. To learn more about AOS-W Instant and for detailed configuration
information, see AOS-W Instant 6.2.1.0-3.4 User Guide.
Getting Started
Unpack and Power on OAW-IAP
After unpacking the AOS-W Instant Access Point (OAW-IAP), check the power
requirements and connect the OAW-IAP.
Connect
To connect the OAW-IAP to your network, plug in a LAN cable to Enet0 (on
the back side of the device) port. The E0 LED turns green.
Provision
OAW-IAPs can be provisioned automatically, through OmniVista, or by
manually connecting to a provisioning network. Use the following methods
based on your OAW-IAP provisioning requirements.
Functional OAW-IAP in the Network
If an OAW-IAP is already configured and is in operational state, connect the
OAW-IAP into the same VLAN or subnet, to automatically configure the new
OAW-IAP.
Based on the OAW-IAP model, you can power on the OAW-IAP by using
an AC adapter or Power over Ethernet (PoE). Use the option that suits
your OAW-IAP deployment environment.
OmniVista and Alcatel-Lucent Activate
If both Alcatel-Lucent Activate and OmniVista are deployed to manage the
network, wait for the radio LEDs to turn green.
AOS-W Instant UI
AOS-W Instant user interface is a standard web-based interface that allows you
to configure and monitor an OAW-IAP network.
To start using the AOS-W Instant UI, perform the following steps:
1. Using a wireless client, scan the wireless networks and connect to the
instant SSID.
2. Using a web browser, go to http://instant.Alcatel-Lucentnetworks.com.
3. Log in to the AOS-W Instant UI with admin and admin as username and
password respectively.
4. If the Country Code window is displayed after a successful login, select a
country from the list.
5. If the AOS-W Instant UI is used for managing OAW-IAPs, proceed to
Creating a Wireless Network. If OmniVista is deployed for managing the
netwok, perform the following steps.
a. Click Set Up Now at the bottom of the AOS-W Instant UI to configure
AirWave. The System window appears.
b. Click the Admin tab. In the AirWave section, enter the Shared Key
and AirWave IP details. Contact your local network administrator to
obtain these details.
Creating a Wireless Network
To create a wireless network using the AOS-W Instant UI, perform the
following steps:
1. From the AOS-W Instant UI main window, click New under the Networks
section. The New WLAN window appears.
2. In the WLAN Settings tab, enter a name (SSID) for the network. This
name is used for identifying the Network.
3. Click Next. The VLAN tab details are displayed.
4. In the VLAN tab, select the required Client IP assignment and Client
VLAN assignment options.
5. Click Next. The Security tab details are displayed.
6. In the Security tab, enter a unique passphrase and retype it to confirm.
You can use the default values or customize the security settings.
7. Click Next. The Access tab details are displayed.
8. In the Access tab, ensure that the Unrestricted access control is
specified.
9. Click Finish. The new network is added and displayed in the Networks
window.
For more information on configuring different types of wireless network such
as Employee, Guest, or Voice, see AOS-W Instant 6.2.1.0-3.4 User Guide.
Verifying the Operating Status
After setting up an OAW-IAP and creating a wireless networks, use the AOS-W
Instant UI or the LEDs to verify the operating status.
Verifying Status Using LEDs
You can use the LEDs to verify that both radios are active after configuration.
For information on the LED status indicators, see the Install Guide provided
with the OAW-IAP package.
Verifying the Status Using AOS-W Instant UI
To verify that the wireless network is available and the SSID is broadcasted,
perform the following steps:
1. Verify that the newly created network is displayed in the Networks
window: for example, employee_network as shown in Figure 1.
Figure 1 Network Window
2. Disconnect the client from instant, the default provisioning network
to which your client system is connected.
3. Connect your client to the newly created network.
The OAW-IAPs boot with factory default configuration and will try to
provision automatically. If the automatic provisioning is successful, the
instant SSID will not be available. If OmniVista and Activate are not
reachable and the automatic provisioning fails, the instant SSID
becomes available and the users can connect to a provisioning network
by using the instant SSID.
Alcatel-Lucent recommends that you change the administrator
credentials after the initial configuration. For more information, see the
Management Authentication Settings section in AOS-W Instant 6.2.1.0-
3.4 User Guide.
The Country Code window appears only when the OAW-IAP-ROW (Rest
of World) variants are installed. The country code setting is not applicable
to the OAW-IAPs designed for US, Japan, and Israel.
The E0 port on OAW-AP134/135, OAW-RAP3WN/3WNP, OAW-RAP108/
109, and OAW-RAP155/155P supports uplink connection.
The E1 port on OAW-AP134/135 and OAW-RAP108/109, E1 and E2
ports on OAW-RAP3WN/3WNP, and E1, E2, E3, and E4 ports on
OAW-RAP155/155P support wired downlink connection.
The E2 port on OAW-RAP3WNP supports Power Sourcing Equipment
(PSE) to supply power to any compliant 802.3af powered (class 0-4)
device.
The OAW-RAP155 supports PSE for 802.3at powered device (class 0-4)
on one port (E1 or E2), or 802.3af powered DC IN (Power Socket) on two
ports (E1 and E2).
AOS-W Instant_QSG.fm Page 1 Wednesday, July 24, 2013 3:23 PM

www.alcatel-lucent.com
26801 West Agoura Road
Calabasas, CA 91301
AOS-W Instant 6.2.1.0-3.4 | Quick Start Guide
Part Number 0511443-01 | July 2013
AOS-W Instant
Quick Start Guide
Contacting Support
Contact Center Online
Main Site http://www.alcatel-lucent.com/enterprise
Support Site https://service.esd.alcatel-lucent.com
Email [e-mail]
Service & Support Contact Center Telephone
North America 1-800-995-2696
Latin America 1-877-919-9526
EMEA [phone] (Toll Free) or [phone]
Asia Pacific [phone]
Worldwide 1-818-878-4507
Copyright
© 2013 Alcatel-Lucent. All rights reserved.
Specifications in this manual are subject to change without notice.
Originated in the USA.
AOS-W, Alcatel 4302, Alcatel 4304, Alcatel 4306, Alcatel 4308, Alcatel 4324, Alcatel 4504, Alcatel 4604, Alcatel
4704, Alcatel 6000, OAW-AP41, OAW-AP68, OAW-AP60/61/65, OAW-AP70, OAW-AP80, OAW-AP92/93, OAW-
AP105, OAW-AP120/121, OAW-AP124/125, OAW-AP175, OAW-IAP92/93/105, OAW-RAP2, OAW-RAP5, and
Omnivista 3600 Air Manager are trademarks of Alcatel-Lucent in the United States and certain other countries.
Any other trademarks appearing in this manual are the property of their respective companies. Includes software
from Litech Systems Design. The IF-MAP client library copyright 2011 Infoblox, Inc. All rights reserved. This
product includes software developed by Lars Fenneberg et al.
Legal Notice
The use of Alcatel-Lucent switching platforms and software, by all individuals or corporations, to terminate Cisco
or Nortel VPN client devices constitutes complete acceptance of liability by that individual or corporation for this
action and indemnifies, in full, Alcatel- Lucent from any and all legal actions that might be taken against it with
respect to infringement of copyright on behalf of Cisco Systems or Nortel Networks.
4. Log in to the AOS-W Instant UI with the administrator credentials. The
instant provisioning network is automatically deleted and will no longer be
available.
Converting an OAW-IAP
An OAW-IAP can be converted to operate as a Campus AP or Remote AP managed
by an Alcatel-Lucent OmniAccess WLAN Switch.
To convert an OAW-IAP through the AOS-W Instant UI, perform the following
steps:
1. Log in to the AOS-W Instant UI with the administrator credentials.
2. Click the Maintenance link at the top right corner of the AOS-W Instant UI
main window.
3. Click the Convert tab.
4. Based on your requirement, select an appropriate option from the Convert
one or more Access Points to drop-down menu.
5. Enter the IP address of the OmniAccess WLAN Switch.
6. Click Convert Now. The OAW-IAP reboots and begins operating in the mode
that you configured.
To convert an OAW-IAP from a controller-managed mode to Instant mode,
manually reset the OAW-IAP.
For more information on the OAW-IAP conversion process, see the AOS-W Instant
6.2.1.0-3.4 User Guide.
To reset an OAW-IAP, press and hold the reset button using a small and
narrow object such as a paperclip. Power on the OAW-IAP without
releasing the reset button. The power LED flashes within five seconds
indicating that the reset is completed.
AOS-W Instant_QSG.fm Page 2 Wednesday, July 24, 2013 3:23 PM