Soyal AR-888-PBI User manual

V210908
SOYAL
ACCESS & INDUSTRIAL CONTROL
A.
MPLA-888XA18/19 (US / EU)
CN1
ON
1 2
J2 J1
N.C.
COM
PB
V+
GND
V+
GND
V+
GND
GND
9-24VDC
9-24VDC
N.O.
COM
N.C.
V+
V-
N.O.
COM
N.C.
V-
V+
or
Function Cable Color Description
Relay COM 1 Green DC24V / 1A
N.O. 2 Blue DC24V / 1A
N.C. 3 Purple DC24V / 1A
Power 4 Black DC 0V
5 Red DC 9-24V
Connector: AR-888-PBI
Touchless Infrared ButtonInstallation
Connector Table / Dip_switch
AR-888-PBI: Touchless Infrared Button - LED Ring (Standard: Green/Red ; By Order: Blue/Red)
Product (US/EU) Tools Easy Install Kit (By Order)
123
Flat Head Hex Socket
Screw: M3x8
Bottom Cover Allen key
2MM / 48*15MM
Electric Bolt
Controller
Request To Exit
Magnetic Lock
Electric Strike
POWER
POWER
Wiring Diagrams
SW1 SW2 OUTPUT
ON ON Pulse
ON OFF Delay 3 Sec.
OFF ON Latch
OFF OFF Delay 6 Sec.
Standby mode Motion
LED G(Green)LED R(RED)LED R(RED)LED G(Green)LED GR
(Green/RED) --
-- LED GR
(Green/RED))Turn around Sensing distance
Clockwise Sensing distance is greater
Counterclockwise Sensing distance is smaller
LED status adjustment
Dip_switch Output Mode
Sensing distance adjustment
2
3
4
#1 #2
#3 #4
ON
1 2
ON
1 2
ON
1 2
ON
1 2
(Example #2)
1
※2
3
4
※1
2
3
4※Default Value
※Default Value
AR-888-PBI
Sensing distance
adjustment
Connector
Dip_switch
LED status
adjustment
3
4
2
1
J2(LED R)
J1(LED G)
Standby
mode Motion
NC NO

V210908
SOYAL
ACCESS & INDUSTRIAL CONTROL
75
81
84
118
20
15
51
3.3
3.3
24
23
86
88
52
51
13
10
60
18
13
16
12
66
3.3
Proportion 1:1
Unit: mm
US Mounting Hole: 73x48x40mm(HxWxD)
Screw hole pitch : 84mm
Suitable for 70X118 1-module ush-mounting box.
( Australian, Italy, USA(501E) Standard)
EU Mounting Hole: 57x53x40mm(HxWxD)
Screw hole pitch : 60mm
Suitable for 86X86 ush-mounting box.
(UK, Continental Europe, Germany Standard)
Cable selection: Use AWG 22-24 Shielded Twist Pair to avoid star wiring.
Use CAT5 for TCP/IP connection.
A.B.C.
D.
2
(Excluded)
By order
5
4
3
3
Pull the cables from the square holes of the eva foam gasket and mounting plate.
Use a screwdriver to screw the mounting plate B onto the wall with Flat Head Cap Philips Tapping Screws (Excluded, the Installer
should prepare before installation.
Connect the cables to the backside of body Cand attach C to Bat lower position of B. Push Cup to make the cogging hooked completely.
Use the Allen key and screws to assemble the body C onto the mounting plate B. Attach the Back Cover Dto C.
(Excluded)
In-wall
Depth
28mm
~35mm 1
Installation