Alecto ADB-19 User manual

ADB-19 Installation
Outdoor-unit - battery placement:
Indoor-unit:
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
ADB-19 Installation
Outdoor-unit:
Indoor-unit:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Connecting:
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1x1x
1x
<10 sec.
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver
●1 x User Manual
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning co
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction
Auto-leaning Code W
Model No.: QH-861AK
VOL
MODE
CODE
5 sec.
Unregister
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can crea
risk of fire and personal injury. Batteries should not be left in an area where the children
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw d
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
ADB-19 Installation
Outdoor-unit:
Indoor-unit:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Connecting:
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1x1x
1x
<10 sec.
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver
●1 x User Manual
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning co
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction
Auto-leaning Code W
Model No.: QH-861AK
VOL
MODE
CODE
5 sec.
Unregister
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can crea
risk of fire and personal injury. Batteries should not be left in an area where the children
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw d
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
CR2032 3V
Lithium Battery
Nameplate
thin-tipped
cover
(not included)
tweezers (not included)
screwdriver
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
CR2032 3V
Lithium Battery
Nameplate
thin-tipped
cover
(not included)
tweezers (not included)
screwdriver

Change melody:
Unregister:
melody-1
~
melody-36
v1.5
Volume 1...6
Lamp / Ring / Lamp & Ring:
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
5 sec.
Frequency: 433MHz ASK
Transmission power: <10mW
EU-CONFORMITEITSVERKLARING
Hierbij verklaar ik, Commaxx, dat het type radioapparatuur ADB-19 conform is met Richtlijn 2014/53/EU.
De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende
internetadres: http://DOC.hesdo.com/ADB-19-DOC.pdf
DECLARATION DE CONFORMITE
Le soussigné, Commaxx, déclare que l’équipement radioélectrique du type ADB-19 est conforme à la directive
2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l’adresse internet suivante:
http://DOC.hesdo.com/ADB-19-DOC.pdf
ÜBEREINSTIMMUNGSERKLÄRUNG
Hiermit erklärt Commaxx, dass der Funkanlagentyp ADB-19 der Richtlinie 2014/53/EU entspricht.
Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:
http://DOC.hesdo.com/ADB-19-DOC.pdf
EU DECLARATION OF CONFORMITY
Hereby, Commaxx declares that the radio equipment type
ADB-19 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is
available at the following internet address:
http://DOC.hesdo.com/ADB-19-DOC.pdf
Connecting:
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
Important Note:
●If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
●Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
●Recycle used batteries following environmental protection practices.
Transmitter Installation:
●Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
●Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity.To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1x1x
1x
<10 sec.
1
Accessories List:
●1 x Receiver ●1 x Transmitter
●1 x User Manual ●1 x Double-sided adhesive
●1 x 3 volts CR2032 battery for transmitter
Technical Specification:
●Frequency: 433.92MHz+100KHz
●Modulation Type: ASK
●Ring Volume:＞85dB(within 0.5m)
●Channel space: 1 million sets of auto-learning codes
●Receiver bandwidth: ±90KHz
●Reception Sensitivity:＞-105dBm
●Transmitter Power:＜10mW
●Power consumption(Receiver): standby:＜0.3W
●Power consumption(Transmitter): standby:＜5uA working:＜10mA
●Power Supply(Receiver): AC110-240V
●Power Supply(Transmitter): DC 3V (1x CR2032)
●Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
Service
Help
Service Help
WWW.ALECTO.NL
[e-mail]
Commaxx B.V.
6466 NG, Kerkrade
The Netherlands
WWW.ALECTO.NL
[e-mail]
Commaxx B.V., Wiebachstraat 37,
6466 NG Kerkrade, The Netherlands
Wiebachstraat 37