Alfain PEGAS 60 PLASMA User manual

ALFA IN a.s © www.alfain.eu PEGAS 60 PLASMA MANUAL EN 04
PLASMA CUTTING MACHINE
PEGAS 60 PLASMA
OPERATING MANUAL

2/19
ALFA IN a.s © www.alfain.eu 3
CONTENT
1. IN RODUC ION ...................................................................................... 3
2. SAFE Y INS RUC IONS AND WARNINGS ........................................... 4
3. CONDI IONS OF USE ............................................................................. 7
4. ECHNICAL DA A ................................................................................... 8
5. MAIN PAR S OF HE MACHINE ............................................................ 9
6. ACCESSORIES ..................................................................................... 11
7. GE ING S AR ED .............................................................................. 13
8. CU ING ............................................................................................... 15
9. MAIN ENANCE ..................................................................................... 17
10. S A EMEN OF WARRAN Y .............................................................. 18
11. DISPOSAL ............................................................................................. 19

3/19
ALFA IN a.s © www.alfain.eu 3
1. INTRODUCTION
Congratulations on your new ALFA IN product. We are proud to have you as
our customer and will strive to provide you with the best service and reliability
in the industry.
his Operating Manual has been designed to instruct you on the correct use
and operation of your ALFA IN product. Your satisfaction with this product and
its safe operation is our ultimate concern. herefore please take the time to
read the entire manual, especially the Safety Precautions. hey will help you to
avoid potential hazards that may exist when working with this product.
Read and understand this entire Manual and your employer’s safety practices
before installing, operating, or servicing the equipment. While the information
contained in this Manual represents the Manufacturer's best judgement, the
Manufacturer assumes no liability for its use.
Machine PEGAS 60 PLASMA is designed for cutting metal on the basis of
modern technology cutting material through a thin beam plasma gas.
PEGAS 60 PLASMA is designed for high-quality cutting of materials up to 25
mm thick carbon steel (for more information, see instructions
below). Productive cutting of carbon steel can be to a thickness of 20 mm.
At lower demands on the quality of the cut can be cut through (separate) the
material thickness to 30 mm.
We reserve the law of adjustments and changes in case of printing errors,
change of technical paramaters, accessories etc. without previous notice.
hese changes may not be reflected in the manuals for use in paper or
electronic form.

4/19
ALFA IN a.s © www.alfain.eu 3
2. SAFETY INSTRUCTIONS AND WARNINGS
1. OPERA ION AND MAIN ENANCE OF PLASMA ARC EQUIPMEN CAN
BE DANGEROUS AND HAZARDOUS O YOUR HEAL H.
2. Plasma arc cutting produces intense electric and magnetic emissions that
may interfere with the proper function of cardiac pacemakers, hearing aids,
or other electronic health equipment. Persons who work near plasma arc
cutting applications should consult their medical health professional and the
manufacturer of the health equipment to determine whether a hazard exists.
3. Once the packing has been opened, make sure that the machine is not
damaged. If in any doubt, call the service centre.
4. his equipment must only be used by qualified personnel.
5. During installation, any electric work must only be carried out by trained
personnel.
6. he machine must be used in a dry place with good ventilation.
7. Make sure that no metal dust can be drawn in by the fan inside the
machine, as this could cause damage to the electronic circuits.
8. It is prohibited to connect more than one INVER ER generator in series or
in parallel.
9. When installing the machine, follow the local regulations on safety.
10. he position of the machine must allow easy access by the operator to
the controls and connectors.
11. When the cutting machine is operating, all its covers and doors must be
closed and well fixed.
12. Do not expose the cutting machine to direct sunlight or to heavy rain.
his equipment conforms to protection rating IP 23 S.
13. he operator must wear gloves, clothes, shoes, and a helmet or a
welder’s helmet, which protect and are fire-resistant in order to protect him
against electric shock, flashes and sparks from cutting.
14. he operator must protect his eyes with safety visor or mask designed for
welding, fitted with standard safety filters. He should also be aware that
during plasma cutting UL RAVIOLE RADIA ION is emitted. herefore it is
vital that his face is also protected from radiation. Ultraviolet rays produce
the same harmful effect as sun burning on unprotected skin.
15. he operator is obliged to warn anyone near the cutting area of the risks
that cutting involves and to arrange to provide adequate protection
equipment.
16. Keep all fumes and gases from the breathing area.
17. Keep your head out of the fume plume.
18. Use an air-supplied respirator if ventilation is not adequate to remove all
fumes and gases.
19. he kinds of fumes and gases from the plasma arc depend on the kind of
metal being used, coatings on the metal, and the different processes. You
must be very careful when cutting or welding any metals which may contain

5/19
ALFA IN a.s © www.alfain.eu 3
one or more of the following:
Antimony Chromium Mercury
Nickel Cobalt Arsenic
Barium Copper Selenium
Beryllium Lead Silver
Cadmium Manganese Vanadium
20. Always read the Material Safety Data Sheets (MSDS) that should be
supplied with the material you are using. hese MSDSs will give you the
information regarding the kind and amount of fumes and gases that may be
dangerous to your health.
21. It is very important to arrange for sufficient ventilation, especially when
cutting in enclosed spaces. We suggest using suitable fume extractors to
prevent the risk of intoxication by fumes or gas generated by the cutting
process.
22. Noise can cause permanent hearing loss. Plasma arc processes can
cause noise levels to exceed safe limits. You must protect your ears from
loud noise to prevent permanent loss of hearing.
23. o protect your hearing from loud noise, wear protective ear plugs and/or
ear muffs. Protect others in the workplace.
24. Noise levels should be measured to be sure the decibels (sound) do not
exceed safe levels.
25. he operator must ensure all flammable materials are removed from the
work area to avoid any risk of fire.
26. he operator must NEVER cut containers that have previously contained
petrol, lubricants, gas or similar flammable materials, even if the container
has been empty for a considerable time. HERE IS A VERY HIGH RISK OF
EXPLOSION.
27. he operator must be aware of all the special regulations which he needs
to conform to when cutting in enclosed spaces with a high risk of explosion.
28. o prevent electric shock, we strongly suggest the following rules:
a) Do not work in a damp or humid environment.
b) Do not use the machine if its cables are damaged in any way.
c) Make sure that the earthing system of the electric equipment is
correctly connected and operational.
d) he operator must be insulated from the metal components connected
to the return wire.
e) he earthing of the piece being worked could increase the risk of
injury to the operator.
29. EN 60974-1 Standard: Open-circuit voltage. During the operation of the
machine, the highest voltage, with which it is possible to come into contact,
is the open-circuit voltage between the clamps. In our generator this voltage
is 310V.
30. he maximum open-circuit voltage of the plasma machines is established
by national and international standards (EN 60974-1) depending on the type

6/19
ALFA IN a.s © www.alfain.eu 3
of current to be used, on its waveform and on the hazards arising from the
work place. hese values are not applicable to the strike currents and those
for stabilisation of the arc that could be above it.
31. he open-circuit voltage, for as many adjustments as possible, must
never exceed the values relating to the various cases shown in the following
table:
Case
Working conditions Open-circuit voltage
1 Places with increased risk of
electric shock
DC current: 113V
peak value
AC current: 68V
peak value and
48V effective
2 Places without increased risk
of electric shock
DC current: 113V
peak value
AC current: 113V
peak value and
80V effective
3 orches held mechanically
with increased protection for
the operator
DC current: 141V
peak value
AC current: 141V
peak value and
100V effective
4 Plasma cutting DC current: 500V
peak value
32. In case 1, the dc machines with rectifier must be built in such a way that,
in case of a fault developing in the rectifier (for example open circuit, short
circuit or lack of power), the permitted values cannot be exceeded. he
plasma cutting machines of this type can be marked with the symbol:
S
33. Before opening the machine switch off the machine and disconnect it
from the power socket.
34. Only personnel authorised by this company can carry out maintenance
on the machine.
PROTECTIVE UTTILITIES
1. Welding helmet with filter shade at least 10
2. Welding gloves
3. Welding apron and cloth
4. Welding boots
RISK OVERVIEW
1. Risk of electric shock.
2. Ultraviolet light and light radiation
3. Risk of inhaling gas fumes and dust particles
4. Burns
5. Noise

7/19
ALFA IN a.s © www.alfain.eu 3
NOTE
The Machine Torches (AUT) must not be used with PEGAS 60 P ASMA. It
may only be used together with PEGAS 60 P ASMA CNC.
NOTE
1. It is forbidden to operate a machine with damaged insulation of the
cutting torch or supply cable.
2. Never operate the machine taken down or damaged covers.
3. It is forbidden to operate the machine in wet environments and outdoors
in rain or snow.
4. Ensure proper grounding clamping pliers, which also reduces the risk of
electric shock.
5. Use prescribed protective utilities, keep them dry.
6. Plasma arc cutting produces intense electric and magnetic emissions that
may interfere with the proper function of cardiac pacemakers, hearing
aids, or other electronic health equipment. Persons who work near
plasma arc cutting applications should consult their medical health
professional and the manufacturer of the health equipment to determine
whether a hazard e ists.
7. Never aim the torch against the eyes, body or other person.
3. CONDITIONS OF USE
1. his equipment must only be used by qualified personnel.
2. During installation, any electric work must only be carried out by trained
personnel.
3. Device complies with IEC 61000-3-12 with following conditions:
Short-circuit power Ssc of network in place at an interface between the
user's supply and the public network (PCC) must be least 3561 kW.
User is obliged to consult with the electricity supplier if the impedance of the
network at this point is that required short-circuit capacity Zmax = 45 mΩ and
whether the device can be connected with a public low-voltage network.
On the nameplate are the following symbols: .
4. Do not expose the plasma machine to direct sunlight or to rain or snow. his
equipment conforms to protection rating IP23S.
5. Place the machine the way that the cooling air can enter the vents without
restriction to. It is necessary to ensure that no impurities, especially metal
particles, are not drawn into the machine.
6. Cutting machine in terms of interference suppression is intended primarily
for industrial premises. In the case of use of other areas may be need for
special measures (see EN 60974-10).
7. The machine must be protected against:
a) Moisture and rain and snow

8/19
ALFA IN a.s © www.alfain.eu 3
b) Mechanical damage
c) Draft and any ventilation of neighbouring machine
d) Excessive overloading - crossing technical parameters
e) Rough handling
ELECTROMAGNETIC COMPATIBILITY
he welding device is in terms of interference designed primarily for industrial
areas. It meets the requirements of EN 60974-10 class A and it isn’t designed
for using in residential areas, where the electrical energy is supplied by public
low-voltage power supply network. It can be here potential problems with
ensuring of electromagnetic compatibility in this areas, due to interference
caused by power lines as well as the radiated interference.
During operation, the device may be the source of interference.
Caution
We warn users, that they are responsible for possible interference from
welding.
4. TECHNICAL DATA
Method Plasma cutting
Mains voltage V/Hz 3 x 400/50-60
Cutting current range /V 20 - 65
Open-circuit voltage U20 V 310
Mains protection 16 @
Max. effective current I1eff 15,6
Cutting current (DC=100%) I2 60
Cutting current (DC=60%) I2 65
Cutting current (DC=x%) I2 90%=65
Max. productive cut. thickness - carbon steel mm 20
Max. cutting thickness - carbon steel
(separate mat.) mm 30
Quality
cutting
thickenss
Carbon steel mm 25
Stainless steel mm 18
luminium mm 15
Copper mm 10
Max. Input pressure bar 8,5
Working pressure bar 5,0
ir consumption l/min 200
rc ignition pneu-mechanic
Current regulation continuous
Protection IP 23 S

9/19
ALFA IN a.s © www.alfain.eu 3
Standards EN 60974-1; EN 60974-10 class
Dimensions (w x l x h) mm 240 x 440 x 595
Weight kg 24
5. MAIN PARTS OF THE MACHINE
FRONT AND REAR PANELS
Picture 1 – he main parts
Pos. Description
A1 Quick connector - earthing cable
A2 Connector - remote control – in standard doesn’t work – only on
request
A3 Connector - torch
A4 Potenciometer-set cut current
A5 LED indicator – when illuminated, the machine is ON.
A6 LED indicator-overheating
when illuminated, please leave the machine turned on and wait on
cooling the machine down.
A7 1. LED indicator flashes – the Retaining Cup isn’t on or is fitted

10/19
ALFA IN a.s © www.alfain.eu 3
badly
2. LED indicator shines – low gas pressure
A8 LED indicator – arc burning – after you press the torch button, it
shines, on the torch is a voltage
A9
Switch
Setting of gas flow
Continuous cutting
Cutting material with gaps – Caution! Higher wear of nozzles and
electrodes
A10 Manometer
A11 Gas fitting
A12 Controler
A13 Mains cable
A14 Switch ON/OFF

11/19
ALFA IN a.s © www.alfain.eu 3
6. ACCESSORIES
PART OF DELIVERY
Pos. Code Description
V9030038 Earthing cable with clamp 3m 10-25 150A
Picture 2 – orch SCP 120 6 m PEGAS – parts
ON REGUEST
Pos. Code Description
SCP1250 Circle Cutting Attachment 120
5302 Air Filter A 1000
5304 Adapter for A 1000 PEGAS PLASMA
S777a Welding Helmet ALFA IN S777a Black
SCP120-6-60 orch Plasma SCP 120 6m PEGAS 60
5864 Set S AR to the torch SCP 120 PEGAS 60
(Recommended S AR set for the torch – Pic. 2) Quantity
7 SCP1207 Swirl Ring 4 Holes 30-70A 1
10 SCP1222-09 Cutting ip 0,9 Contact 30-40A 2
9 SCP1220-10 Cutting ip 1,0 40-50A 2
9 SCP1220-11 Cutting ip 1,1 50-60A 2
9 SCP1220-12 Cutting ip 1,2 60-70A 2

12/19
ALFA IN a.s © www.alfain.eu 3
5 SCP1204 Electrode SCP 120 10
14 SCP1230 Rataining Cup 30-70 A 1
11 SCP1226-10 Cutting ip 1,0 Contact 40-50A 1
11 SCP1226-11 Cutting ip 1,1 Contact 50-60A 1
16 SCP1232 Shield Cup Body 1
19 SCP8041 Shield Cup Contact 30-80 A 1
Parts of the torch (Pic. 2)
1 SCP1201 Torch Head SCP 120
1a 5008 O-Ring
2 SCP2516 Button SCP 120 PARKER
3 SCP8014 Handle SCP 120
4 SCP1202 Cooling Tube SCP 120
5 SCP1204 Electrode SCP 120
6 SCP1206 Swirl Ring 6 Holes 80-120A
7 SCP1207 Swirl Ring 4 Holes 30-70A
9 SCP1220-10 Cutting ip 1,0 40-50A
9 SCP1220-11 Cutting ip 1,1 50-60A
9 SCP1220-12 Cutting Tip 1,2 60-70A
10 SCP1222-09 Cutting ip 0,9 Contact 30-40A
11 SCP1226-10 Cutting ip 1,0 Contact 40-50A
11 SCP1226-11 Cutting ip 1,1 Contact 50-60A
11 SCP1226-12 Cutting ip 1,2 Contact 60-70A
13 SCP1228-22 Cutting ip
14 SCP1230 Retaining Cup 30-70 A
16 SCP1232 Shield Cup Body
17 SCP1251 Cutting Buggy SCP 120
18 SCP1240 Double Pointed Spacer SCP 120
19 SCP8041 Shield Cup Contact 30-80 A
21 SCP8043 Shield Cup Gouging
Note – the bold items are equipped on the torch

13/19
ALFA IN a.s © www.alfain.eu 3
7. GETTING STARTED
Getting started must be consistent with technical data and conditions of use
(especially with 3. point).
FIRST STEPS
NOTE his equipment must only be used by qualified personnel.
1. Before beginning work is necessary to connect the machine to the mains.
2. Check completeness of the mounted cutting torch.
3. Connect the torch to the connector. By means of the thorn (part of the
delivery) press the safety pin. urn the nut of the connecter clock wise and
tight it properly.
4. Connect the mains cable A13 to the on the network according 4
ECHNICAL DA A
5. Connect the compressed air on connector A11 on the rear wall of the
machine.
6. Set the air pressure by means of regulator A12 and manometer A10 to 5
bars.
7. Connect the mains plug to the mains socket.
8. After turning on the ON/OFF switch A14 the display A5 will illuminate.
9. Connect the work lead cable to the material being cut and to the
connector A1.
10. Check up the input air pressure (min 5 bar, max 8,5 bar) and make a
regulation if necessary.
11. Set potentiometer A4 to the cutting power you need.
12. Fit the torch with appropriate type of cutting tip electrode and shield
cup according to the selected cutting current.
13. Press the trigger on the cutting torch, the pre gas will flow for 1 s.
14. The pilot arc will start.
15. Shift the torch with the pilot arc close to the material, the pilot arc will
change to cutting arc automatically. If you do not start cutting within 2 s,
the arc will snuff off. If the torch delays during the cutting from the
material, the arc will snuff off. In case that the machine is in mode Cutting
material with gaps – switch A9 position , cutting arc will change to pilot
arc and if you do not start cutting within 2 s, this arc will snuff off.
16. To finish the cutting process, release the torch trigger.
REQUIREMENTS FOR SOURCE OF COMPRESSED AIR
1. Delivered air pressure must be max. 8,5 bar and min. 5 bar.
2. Air consumption minimal 220 l/min
3. Compressed air for the plasma must be clean and dry.

14/19
ALFA IN a.s © www.alfain.eu 3
4. Pressure dew point +3 ° C
5. Ma imum oil content 0.1 mg/m3
6. Ma imal size of solid particles 15 microns
7. The minimal size of an air tank is 50 l
8. No additional oiling if the pressure air is permitted. That could damage
the plasma machine and the cutting torch.
OPTIONAL AIR FILTERS
o achieve high quality cutting and to avoid serious disturbances to the torch it
is highly advised to include the air filter.
Pos. Item No Description
B2 5302 Air filter A 1000
B1 5304 Set for filter A 1000 to PEGAS Plasma
NOTE Max. allowable pressure of filter A 1000 is 8,5 bar
Picture 3 – Air filter

15/19
ALFA IN a.s © www.alfain.eu 3
8. CUTTING
he table below show just referential values. he real values may change
according the material qualities. he darker colour highlights heat area where
the consumables are more worn off.
S 105 Carbon steel – material thickness and recommended
cutting tips
Cutting
current
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
ip
50 A
4546 (1,0)
70 A
4547 (1,2)
100 A
4548 (1,4)
1. Press the torch trigger. he pilot arc will ignite. hen you have to
immediately attach the torch to the cut material. At this point begins to burn
the main arc between the torch and the material.
2. Move the torch with a constant speed. Cutting speeds vary according to
torch output amperage, the type of material being cut, and operator skill.
3. Output current setting or cutting speeds may be reduced to allow slower
cutting when following a line, or using a template or cutting guide while still
producing cuts of excellent quality
4. o achieve a good cutting quality make sure the distance between the tip
and the material is about 3,5 mm. he Stand Off Guide located at the end of
the plasma torch guarantees the distance. At a greater distance decreases
cutting power and the arc may go off. With too small distance the torch parts
will be worn off faster.
5. Plasma cutting may be done in all possible positions (vertically, horizontally,
overhead, vertical ascending and descending), but as far as possible
choose primarily horizontal cut. In other positions the operator is
increasingly threatened by flying drops of molten material.
6. We recommend starting cutting at the edge of the material. If needed to
start from the centre of the material, or to cut hole into the material, slightly
tilt the torch head and gradually it straighten into a vertical position so the
spraying material would not damage the cutting tip (see Pic. 4). his
workflow must always be followed, if the thickness of material is above
above 3 mm.
7. In case of cutting in the corner or around the corner (see Pic. 5), use the
long electrode and cutting tip. he cutting power while using the Long
cutting tip is decreased.

16/19
ALFA IN a.s © www.alfain.eu 3
Picture 4 - Cutting Picture 5 - Cutting
IMPORTANT RULES
1. he pilot arc burning time should be limited only to the time necessary. It
lowers the wear of the cutting tips and electrodes.
2. Never turn off the main switch immediately after finishing cutting but always
leave time to run cooling cycle to cool down the torch. Immediate turn-off
only in case of emergency.
3. Ensure a good el. Contact of the work lead clamps and cutting material.
4. Check and timely exchange cutting tips and the electrodes. Lifetime of these
parts is only a few hours of cutting time and is highly dependent on
compliance with the principles of good cutting.
5. Disconnect the machine from the mains before replacing the torch
consumable parts.
6. Unplug the machine from the mains before any intervention inside the
machine.
7. PEGAS 60 PLASMA is adapted for use with torch Plasma SCP 120
PEGAS 60. This combination comply with EN 60974-7 Article
10.1.4. Using any other type and design of a torch must be approved by
ALFA IN a.s.
8. Imperfect capture of condensate would cause its elimination in the area of
the cutting tip and it would prevent ignition of the pilot arc.
SOURCES OF POOR QUALITY CUTS
Shallow penetration of the cut
1. he cutting speed is too high. Make sure the slope of the cutting arc does
not exceed about 15 ° (see Pic. 6).
2. High wear of the cutting tip or electrode (see Pic. 7)
3. oo large thickness of material and not adequately chosen value of current
and diameter of the cutting tip.
4. Bad contact between the work lead clamps and material.
Cutting arc is unstable, goes off and "shoots"
1. Worn out cutting tip or electrode
2. High pressure
3. Impurities in the pressure air
4. Not captured water condensate

17/19
ALFA IN a.s © www.alfain.eu 3
Conical cut
1. If there is a false cut (see Pic. 8) turn off the machine, release the shield cup
and rotate the cutting tip about 1/4 and again try to cut.
2. Damaged cutting tip and electrode
3. he position of the torch is not perpendicular to the material
4. oo large distance from the cutting tip to the material.
Max 15
o
Picture 6 Picture 7 Picture 8
9. MAINTENANCE
1. A great care should be taken to the cutting torch. he molten material
sprays while cutting. his sputter contaminates the interior space of the
torch. he worn parts (consumables) of a plasma torch should be regularly
maintained and timely exchanged. Regularly check the condition of diffuser
channels (see diagram of the torch). If contaminated, you must clean it with
a pressure air or to replace the diffuser. Poor state of the diffuser has a
negative impact on the quality of cutting and causes very strong interference
that may cause the collapse of the machine control electronics or influence
the surrounding devices. If the cable bundle of the torch is worn out it must
be replaced immediately - danger of electrical shock.
2. Disconnect the PEGAS from the mains supply voltage before
disassembling.
3. Special maintenance is not necessary for the control unit parts in the
plasma cut machine. If these parts are damaged for any reason,
replacement is recommended.
CAU ION 
4. Do not blow air into the plasma cut during cleaning. Blowing air into the
plasma cut can cause metal particles to interfere with sensitive electronic
components and cause damage to the welder.
5. o clean the plasma cut, disconnect it from the mains supply voltage then
open the enclosure and use a vacuum cleaner to remove any accumulated
dirt and dust. he plasma cut should also be wiped clean. If necessary,
solvents that are recommended for cleaning electrical apparatus may be

18/19
ALFA IN a.s © www.alfain.eu 3
used.
6. roubleshooting and repairing of PEGAS equipment should only be carried
out only by suitably qualified or competent person.
7. A ‘competent person’ must be a person who has acquired through training,
qualification or experience, or a combination of them, the knowledge and
skills enabling that person to safely carry out a risk assessment and repairs
to the electrical equipment in question.
8. he person carrying out the servicing needs and repairs must know what to
look at, what to look for and what to do.
10. STATEMENT OF WARRANTY
1. In accordance with the warranty periods stated below, ALFA IN guarantees
the proposed product to be free from defects in material or workmanship
when operated in accordance with the written instructions as defined in this
operating manual.
2. ALFA IN products are manufactured for use by commercial and industrial
users and trained personnel with experience in the use and maintenance of
electrical welding and cutting equipment.
3. ALFA IN will repair or replace, at its discretion, any warranted parts or
components that fail due to defects in material or workmanship within the
warranty period. he warranty period begins on the date of sale to the end
user.
4. If warranty is being sought, please contact your ALFA IN product supplier
for the warranty repair procedure.
5. ALFA IN warranty will not apply to:
a) Equipment that has been modified by any other party other than ALFA
IN’s own service personnel or with prior written consent obtained from
ALFA IN Service Department.
b) Equipment that has been used beyond the specifications established
in the operating manual.
c) Installation not in accordance with the installation/operating manual.
d) Any product that has been subjected to abuse, misuse, negligence or
accident.
e) Failure to clean and maintain (including lack of lubrication,
maintenance and protection), the machine as set forth in the
operating, installation or service manual.
6. Within this operating manual are details regarding the maintenance
necessary to ensure trouble free operation.
7. Validity condition of warranty is, that the cutting machine must be used only
with the torch, which is said in this manual.
NO E 
Warranty repairs must be performed by either an ALFA IN Service Centre, an
ALFA IN distributor or an Authorised Service Agent approved by the company

19/19
ALFA IN a.s © www.alfain.eu 3
ALFA IN.
11. DISPOSAL
Only for EU countries. Do not dispose of electric tools together
with household waste material.
In accordance with European Council Directive 2002/96/EC on
electrical and electronic equipment waste and its
implementation in accordance with national law, electric tools
that have reached the end of their service life must be
collected separately and returned to an environmentally
compatible recycling facility.