Alkalite Tracpod 84 User manual

User Manual
Tracpod 84
Version 1.1

____________________________________________________________________________
Page 1 of 13 Tracpod 84 User Manual

Introduction
Thank you for purchasing Tracpod 84.
Tracpod 84 is a LED batten for professional use. With cutting-edge RGB color mixing technology
capable to generate up to 16.5 million colors for use in stage production and fixed installation.
The LED batten contains ten LED modules and each can separate into four individual sections,
provides total of forty pixels capable to run graphics or matrix when multiple unit are used
together. Tracpod 84 can be operated in stand-alone or advance control via external DMX
controller.
WHAT IS INCLUDED
z1 x Tracpod 84 LED batten
z1xPowercord
z1 x Power connection cable
zUser manual
Carefully unpack the carton, check the contents to ensure that all parts are present, and have
been received in good condition. If any parts appear damaged or missing, notify the shipper
immediately and retain packing material for inspection. In the event that the fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and
packing.
1.1 Features
zDMX 512.
zStandard 4 channels and full function 7 channels DMX control.
zStand – alone operation:
Master/Slave.
Manual color mixing
Auto-chases with adjustable speed and fade.
16 auto chases.
z40 sections of LED module to create LED matrix effect.
____________________________________________________________________________
Page 2 of 13 Tracpod 84 User Manual

1.2 Overview
1. LED Module
2. Hanging Bar
3. Gear Screw
4. Fan
5. Power Switch
6. Mode Button
7. Select Button
8. Up Button
9. Down Button
10. Fuse Holder
11. Safety Ring
12. Microphone
13. Sensitivity Level
14. Fan
15. Power Input
16. 3-PIN DMX Input
17. 5-PIN DMX Input
18. 5-PIN DMX Output
19. 3-PIN DMX Output
20. Power Output
____________________________________________________________________________
Page 3 of 13 Tracpod 84 User Manual

1.3 Safety Instructions
CAUTION
UNPLUG MAINS BEFORE INSTALLING OR WIRING THE FIXTURE
User must be qualified to be involved with installation and maintenance of this product. User
must follow the safety instruction and warning notes written in this manual.
CAUTION
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE
IMPORTANT
zFor indoor use only
zKeep dry
zInstall only in well ventilated areas
zDo not attempt to open the controller or fixture, no user serviceable parts inside.
zBefore attaching the device, make sure the installation surface can hold a minimum point
load of ten times the device’s weight.
Installation
2.1 Connection to the mains
i. AC Power
Tracpod 84 is available in AC100-240V 50-60HZ and is supplied to match your local voltage
and frequency.
ii. Replacing Plug
The power cable must be fitted with a grounding-type cord cap (earthed type mains plug) that
fits your power distribution system.
____________________________________________________________________________
Page 4 of 13 Tracpod 84 User Manual

Wire (EU) Wire (US) Pin Marking
Brown Black Live L
Blue White Neutral N
Yellow Green GND
2.2 Connection between fixtures
The fixture is equipped both 3 and 5-PIN XLR sockets for DMX input and output. Only use a
shielded twisted pair cable designed for 3 or 5-PIN XLR plugs and connectors in order to
connect the controller with fixture or one fixture with another.
i. DMX Serial Data Link
If you are using the standard DMX controller, you can connect the DMX output of the
controller directly with the DMX input of the first fixture in the DMX-chain. Connect the DMX
output of first fixture in the chain with DMX input of next fixture. Always connect one output
with input of next fixture until all fixtures are connected.
____________________________________________________________________________
Page 5 of 13 Tracpod 84 User Manual
ii. Master/Slave Data Link

Connect the DMX output of the master fixture in the data chain with the DMX input of first
slave fixture. Always connect output with the input of next slave fixture until all slave fixtures
are connected.
2.3 Mounting the fixture
i. Truss Mount
Fixture should be hung on truss structure using a mounting clamp. Always secure the fixture
with a secondary safety attachment.
____________________________________________________________________________
Page 6 of 13 Tracpod 84 User Manual

ii. Wall Mount
Mount the fixture to wall as illustrated below. Before attaching the device, make sure the
installation surface can hold a minimum point load of 10 times the device’s weight.
iii. Floor Mount
Mount the fixture on the ground floor as illustrated below.
____________________________________________________________________________
Page 7 of 13 Tracpod 84 User Manual

____________________________________________________________________________
Page 8 of 13 Tracpod 84 User Manual

____________________________________________________________________________
Page 9 of 13 Tracpod 84 User Manual

____________________________________________________________________________
Page 10 of 13 Tracpod 84 User Manual

____________________________________________________________________________
Page 11 of 13 Tracpod 84 User Manual

TechnicalSpecification
Power
Input Voltage: AC100-240V 50-60HZ
Power Consumption: 120 W
Fuse: T2.0A
Light Source
LED: 840 RGB LED (280 Red,280 Green, 280 Blue)
Beam angle: 15°
Performance
2300 LUX @ 1M
1000 LUX @ 2M
Control and Programming
Protocol: USITT DMX 512
DMX Channels: 4, 7, 8, 20, 40, 160
Control Options: DMX, Master/Slave, Manual color mix, Auto-chase
Connections
Power: Neutrik Powercon
Data: 3 and 5-PIN XLR
Dimensions and Weight
Length: 1010 mm
Width: 258 mm
Height: 236 mm
Weight: 11.5 kg
____________________________________________________________________________
Page 12 of 13 Tracpod 84User Manual

Maintenance
Keep the fixture dry and only install in well-ventilated areas.
Clean the fixture with a moist, lint-free cloth. Never use alcohol or solvents.
To maintaining adequate cooling, clean the dust from air vent regularly.
Fuse Replacement
1. Unplug mains before replacing fuse.
2. Unscrew the fuse holder using a flat head screwdriver (anti-clockwise).
3. Remove the damaged fuse from its holder and replace with exact same type fuse.
4. Insert the fuse holder back in its place then reconnect power.
____________________________________________________________________________
Page 13 of 13 Tracpod 84 User Manual

Alkalite LED Technology Corp.
Website: www.alkalite.com Email:[email protected]
PMA0100