Allen-Bradley 1336 PLUS II User manual

Bulletin 2362 Units Bulletin 2362HA
125HP Roll-Out Unit
Selection Guide
Bulletin 2362 -
Digital AC Drives in
CENTERLINE®
Motor Control
Centers
1336 PLUS™ - Variable Frequency
1336 PLUS™ II
1336 FORCE - Vector Control
1336 IMPACT
PowerFlex® 700
PowerFlex® 700S

Table of Contents
Preface Introduction
About This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-1
General Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-1
Plug-In Drive Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-2
Frame-Mounted Drive Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-2
Roll-Out Drive Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-3
UL Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-3
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p-3
Chapter 1 PowerFlex® 700 and 700S Product Selection
Catalog Number Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Frame Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Drive Unit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Chapter 2 1336 PLUS™ Variable Frequency, 1336 PLUS™ II, 1336 FORCE - Vector Control, 1336 IM-
PACT Product Selection
Catalog Number Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Frame Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Drive Unit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Chapter 3 Motor Control Center Vertical Sections
Features and Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Chapter 4 Busbar Splice Kits
Understanding Busbar Splice Catalog Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Determining Splice Kit Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Splice Kit Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Power Bus Splice Kit Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Control Bus Splice Kit Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
PE/TE Bus Splice Kit Catalog Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

ii Table of Contents

Preface
Introduction
About This Publication Motor Control Centers offer a convenient design for the configuration of
AC drive lineups. When configured in conjunction with a Bulletin 2100
main incoming structure, the CENTERLINE®thru-bus solution eliminates
the challenge of low-voltage power distribution for drives.
We designed this publication to help you configure AC drive equipment
within Bulletin 2100 CENTERLINE Motor Control Center (MCC)
sections. The selection tables in this publication will help you specify the
necessary sections and units.
Important: When using this publication, please be sure to read all
footnotes. Footnotes are used throughout this publication to
advise you of configuration and limitation of structures, units,
and options.
For PowerFlex® drive units listed in Table 1.A:
•select drive unit options using Table 1.B
•select MCC vertical sections selected using Table 3.A
For 1336 drive units listed in Table 2.A:
•elect drive unit options using Table 2.B
•select MCC vertical sections selected using Table 3.A
If there is a need to purchase a separately-assembled unit (for example, if a
spare unit is desired), select the unit as listed in Table 1.A or Table 2.A.
When constructing the catalog number string, use the “N” enclosure
designation for NO structure assembly.
Options or equipment not offered through the 2362 standard AC drive unit
program can be provided to you as an engineered solution. Contact your
local Rockwell Automation Drive Systems representative.
General Product Description Bulletin 2362 AC motor drive units are specifically designed for use in
CENTERLINE® MCC lineups. You may select from numerous 1336
PLUS® Variable Frequency, 1336 PLUS® II Variable Frequency, 1336
FORCE Field-Oriented Control Vector, 1336 Impact, PowerFlex® 700, and
PowerFlex® 700S digital AC motor drives. You may have these drives
configured for either a common-AC or a common-DC power bus
configuration.
NEMA Class I, Type A-rated units are standard. To provide either a NEMA
Type 1 or a NEMA Type 1 with gaskets enclosure rating, the unit must be
installed into an appropriately-sized MCC vertical section. Terminals

p-2 Introduction
mounted within the drive units allow for the connection of remote operator
devices, I/O signals, etc.
Note: NEMA Type 1 is the standard feature; and NEMA Type 1 with unit
door area gaskets and door fan filters is available as an option.
A variety of available options provide increased unit functionality. The
following drive units are available:
Plug-In Drive Units
The basic standard plug-in drive unit includes:
•the selected drive, mounted and wired in an MCC bucket
•a fused-disconnect switch with an operator mechanism and appropriate
fuses
•power and ground stabs for connecting to bus structure
•stab-to-disconnect wiring
•output common-mode chokes
•a unit support pan
•a vented door with fan(s), if appropriate
Note: MCC units that contain plug-in buckets come standard with
manual, vertical bus shutters.
Frame-Mounted Drive Units
The basic standard frame-mounted drive unit includes:
•the selected drive, mounted and wired on a panel-mounted assembly
•a fused-disconnect switch with an operator mechanism and appropriate
fuses
•bus-to-disconnect wiring
•output common-mode chokes
•a vented door with fan(s), if appropriate
Drive Frames Unit Type
1336 A, B, C plug-in
D, E, F, G roll-out
PowerFlex® 0, 1, 2, 3 plug-in
4, 5, 6, 9 frame-mounted

Introduction p-3
Roll-Out Drive Units
The basic standard roll-out drive unit includes:
•the selected drive, mounted and wired on a roll-out chassis assembly
•a fused-disconnect switch with an operator mechanism and appropriate
fuses
•bus-to-disconnect wiring
•output common-mode chokes in all D, E, and F-frame units and in
G-frame 2362H units (common DC bus 1336 FORCE)
•a vented door with fan(s), if appropriate
Note: All D and E-frame units and common DC bus F-frame units are
mounted in 20" deep vertical sections. Common AC bus F-frame
units and all G-frame units are mounted in 20" + 5" (bumpback)
deep vertical sections for ease of serviceability.
UL Certification Bulletin 2100 CENTERLINE® Motor Control Centers are certified by
Underwriters Laboratories, Inc. (UL), Standard UL 845. The 2362 family of
AC drive units are UL/cUL listed. All vertical sections and units certified by
UL will carry the label. Vertical sections and units are labeled separately.
Documentation The customer is supplied with copies of the following:
•the unit wiring diagram and installation instructions
•publications
–Bulletin 2300 Drive Systems Installation Manual (2300-5.1)
–the appropriate AC drive user manual
–Receiving, Handling, and Storing Motor Control Centers (2100-5.5)
For additional documentation, consult your Rockwell Automation Sales
Office.

p-4 Introduction
Notes:

Chapter 1
PowerFlex® 700 and 700S Product Selection
Catalog Number
Explanation
Use the following tables for determining the catalog number used to order
PowerFlex 700 and 700S drives in Bulletin 2362 MCCs.
2362 S A - 4 A B - 48 DA -OPTIONS
Drive Type
Q PowerFlex® 700 (AC Common Bus)
R PowerFlex® 700 (DC Common Bus)
S PowerFlex® 700S (AC Common Bus)
T PowerFlex® 700S (DC Common Bus)
Wiring Type
A“A”Type
B “A” Type Power Wiring with
Bottom Exit
T “A” Type Power Wiring with
Top Exi t
Frame Size
See Table 1.A on
page 1-2
Enclosure
A NEMA Type 1 with no
gaskets or door fan filters
J NEMA Type 1 with gaskets
or door fan filters
Input Voltages
A 230V AC Bus
J 380V AC Bus
B 460V AC Bus
C 575V AC Bus
D 310V DC Bus
V 512V DC Bus
E 620V DC Bus
F 775V DC Bus
Horsepower Rating(3)
85 0.33
33 0.5
34 0.75
35 1.0
36 1.5
37 2.0
38 3.0
39 5.0
40 7.5
41 10
42 15
43 20
44 25
45 30
46 40
47 50
48 60
49 75
50 100
51 125
52 150
54 200
56 250
57 300
58 350
59 400
60 450
61 500
62 600
63 650
64 700
66 800
Disconnect Type
DA Fused Disconnect
Options
See Table 1.B on page 1-3

1-2 PowerFlex® 700 and 700S Product Selection
Frame Selection The following table is used to determine the frame size required based on
the desired Drive Type, Input Voltage and Horsepower.
Table 1.A PowerFlex 700 ad 700S Frame Selection
PowerFlex® 700 Frame Sizes
Drive
Type
Code Input Voltage
Duty
Rating
0
(2.0 SF
20” Wide)
1
(2.0 SF
20” Wide)
2
(2.0 SF
20” Wide)
3
(3.0 SF
20” Wide)
4
(6.0 SF
20” Wide)
5
(6.0 SF
20” Wide)
6
(6.0 SF
25” Wide)
Q230V AC ND - HP 0.5 - 1 2 - 7.5 10 15 - 20 25 - 30 40 - 50 60 - 75
HD - HP 0.33 - 0.75 1.5 - 5 7.5 10 - 15 20 - 25 30 - 40 50 - 60
380V AC ND - kW 0.75 - 4 7.5 - 11 15 - 18.5 22 - 37 45 55 - 75 90 - 132
HD - kW 0.55 - 3 5.5 - 7.5 11 - 15 18.5 - 30 37 45 - 55 75 - 110
460V AC ND - HP 0.5 - 7.5 10 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150
HD - HP 0.33 - 5 7.5 - 10 15 - 20 25 - 40 50 60 - 75 100 - 125
575V AC ND - HP 0.5 - 10 10 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150
HD - HP 0.75 - 7.5 7.5 - 10 15 - 20 25 - 40 50 60 - 75 100 - 125
R310V DC ND - HP 0.5 - 1 2 - 7.5 10 15 - 20 25 - 30 40 - 50 60 75
HD - HP 0.33 - 0.75 1.5 - 5 7.5 10 - 15 20 - 25 30 - 40 50 - 60
512V DC ND - kW 0.75 - 4 7.5 - 11 15 - 18.5 22 - 37 45 55 - 75 90 - 132
HD - kW 0.55 - 3 5.5 - 7.5 11 - 15 18.5 - 30 37 45 - 55 75 - 110
620V DC ND - HP 0.5 - 7.5 10 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150
HD - HP 0.33 - 5 7.5 - 10 15 - 20 25 - 40 50 60 - 75 100 - 125
775V DC ND - HP 0.5 - 10 10 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150
HD - HP 0.75 - 7.5 7.5 - 10 15 - 20 25 - 40 50 60 - 75 100 - 125
PowerFlex® 700S Frame Sizes
Drive
Type
Code
Input
Voltag e
Duty
Rating
1
(2.0 SF
20” Wide)
2
(2.0 SF
20” Wide)
3
(3.0 SF
20” Wide)
4
(6.0 SF
20” Wide)
5
(6.0 SF
20” Wide)
6
(6.0 SF
25” Wide)
9
(6.0 SF
30” Wide)
10
(6.0 SF
35” Wide)(1)
S230V AC ND - HP 0.5 - 7.5 10 15 - 20 25 - 30 40 - 50 60 - 75 NA NA
HD - HP 0.33 - 5 7.5 10 - 15 20 - 25 30 - 40 50 - 60 NA NA
380V AC ND - kW 0.75 - 11 15 - 18.5 22 - 37 45 55 - 75 90 - 132 132 - 160 (Future)
HD - kW 0.55 - 7.5 11 - 15 8.5 - 30 37 45 - 55 75 - 110 110 - 132 (Future)
460V AC ND - HP 0.5 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150 200 - 250 (Future)
HD - HP 0.33 - 10 15 - 20 25 - 40 50 60 - 75 75 - 125 150 - 200 (Future)
575V AC ND - HP 0.5 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150 150 - 200 (Future)
HD - HP 0.33 - 10 15 - 20 25 - 40 50 60 - 75 100 - 125 150 (Future)
T310V DC ND - HP 0.5 - 7.5 10 15 - 20 25 - 30 40 - 50 60 - 75 NA NA
HD - HP 0.33 - 5 7.5 10 - 15 20 - 25 30 - 40 50 - 60 NA NA
512V DC ND - HP 0.75 - 11 15 - 18.5 22 - 37 45 55 - 75 90 - 132 132 - 160 (Future)
HD - HP 0.55 - 7.5 11 - 15 8.5 - 30 37 45 - 55 75 - 110 110 - 132 (Future)
620V DC ND - HP 0.5 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150 200 - 250 (Future)
HD - HP 0.33 - 10 15 - 20 25 - 40 50 60 - 75 100 - 125 150 - 200 (Future)
775V DC ND - HP 0.5 - 15 20 - 25 30 - 50 60 75 - 100 125 - 150 150 - 200 (Future)
HD - HP 0.33 - 10 15 - 20 25 - 40 50 60 - 75 100 - 125 150 (Future)
(1) Frame 10 is a 25 inch deep, flush-back enclosure.

PowerFlex® 700 and 700S Product Selection 1-3
Drive Unit Options Table 1.B PowerFlex® 700 and 700S Drives
Options Available to All Units:
Option Option Code Description
Control Power
Source(1)(6)
6P Individual 115V AC-secondary, control power transformer (supplied per drive unit). Includes primary fusing
6TB 115V AC control power, factory wired from 115V AC control bus to drive unit (requires control bus)
6SC 115V AC control power supplied by customer
Auxiliary Contact for
Disconnect(3)
98 (1) normally open (Y = option avail.)
99 (1) normally closed (Y = option avail.)
Wire Label Upgrade
Option(10)
14WLBL Brady Datab™ wire labels
T-Handles(2) 111 T-handles on doors and 3” vertical wireway (present in MCC sections containing frame 0, 1, 2, & 3 drive units
110 Standard handles
Door-Mounted
Devices(4)
1ES Hardwired-interface-stop-pushbutton; for drive-disable function
4EA Control-power-on pilot light
4EW Drive-faulted pilot light
Miscellaneous J11 Audio phone jack
J12 115V AC, 15A, duplex receptacle
Unit Door
Nameplates(1)
M3EW Phenolic label with white background and black lettering
N3EB Phenolic label with black background and white lettering
N3ER Phenolic label with red background and white lettering
Communication
Adapters(1)(15)
14PNA No Communication adapter
14PCNC DPI - ControlNet adapter, coaxial cable
14PCNF DPI - ControlNet adapter, fiber optic
14PDF1 DPI - RS485 DF-1 adpater
14PDPV1 DPI - PROFIBUS DPV-1 adapter
14PEA DPI - Ethernet adapter
14PG1 DPI - Single-Point Remote I/O (RIO) adapter
14PG5 DPI - DeviceNet adapter
14PHVA DPI - RS485 HVAC adapter (future)
14PIB DPI - Interbus adapter (future)
14PLW DPI - LonWorks® adapter (future)
Communication
Adpater (PowerFlex
700S with DriveLogix
Only)(1)(15)
14DLD ELC - DeviceNet adapter
14DLE ELC - EtherNet adapter
14DLOC ELC - ControlNet adapter, coaxial cable
14DLOF ELC - ControlNet adapter, fiber optic
14DLORC ELC - ControlNet Redundant adapter, coaxial cable
14DLORF ELC - ControlNet Redundant adapter, fiber optic
Human Interface
Module (HIM)(3)
14HAPC Door-mounted HIM, Programmer Only LCD
14HA3C Door-Mounted HIM with full numeric LCD
HA1C Drive-Mounted Him with analog LCD
HA2C Drive-Mounted HIM with digital LCD
HA3C Drive-Mounted HIM with full numeric LCD
HAP Door-Mounted HIM Programmer Only LCD
Drive Enclosure(1) 14DO Open
14D1 NEMA 1
14D12 NEMA 12
14DF Flange

1-4 PowerFlex® 700 and 700S Product Selection
Drive Duty Cycle(1) 99ND Normal Duty
99HD Heavy Duty
Emissions(1) 14EMA CE filter and common mode choke(18)(19)(21)
14EMB CE filter and no common mode choke(20)(21)
14EMB1 CE filter and external common mode choke(22)
14EMN No CE filter and no common mode choke(22)(23)
14EMN1 No CE filter and external common mode choke(22)(23)
Documentation(1)(16) N No documentation
A English User Manual
E Quick Start Guide and CD
I/O Selection
(PowerFlex 700
Only)(1)
14IOC Vector I/O, 24V
14IOD Vector I/O, 115V
Control (PowerFlex
700S Only)(1)
14CIOA Phase II with expanded cassette, no Logix extras, no SynchLink™
14CIOB Phase II with expanded cassette, no Logix extras, with SynchLink
14CIOC Phase II with expanded cassette, with Logix extras, no SynchLink(14)
14CIOD Phase II with expanded cassette, with Logix extras, with SynchLink(14)
14CIOG Phase II slim cassette, no Logix extras, no SynchLink
14CIOH Phase II slim cassette, no Logix extras, with SynchLink
Configurations(1) ELC2SNN Phase II, no DriveLogix, no embedded comm.
ELC2SNE Phase II, no DriveLogix, EtherNet/IP embedded comm.
ELC2SNC Phase II, no DriveLogix, ControlNet embedded comm.
ELC2SEN Phase II, 5730 DriveLogix™, no embedded comm.
ELC2SEE Phase II, 5730 DriveLogix, EtherNet/IP embedded comm.
ELC2SEC Phase II, 5730 DriveLogix, ControlNet embedded comm.
Compact I/O
Cable(17)
CIOL Drive to left bank expansion
CIOR Drive to right bank expansion
Feedback
(PowerFlex 700
Only)(1)
14ENC Standard encoder
14ENCN No feedback PCB
Feedback
(PowerFlex 700S
Only)(1)
14EN2 Second encoder feedback(14)
14HEF Heidenhain feedback PCB(13)
14HENC Hi-Resolution Stegmann resolver feedback PCB(13)
14MDI Multi-Device Interface(13)
14PN No feedback PCB
14RES Resolver feedback PCB(13)
14SO Safe-Off (includes second encoder feedback)(14)
Braking Option(1) 16BI Braking IGBT included
16BNI Braking IGBT not included
Braking Resistor(1) 14BR Braking resistor included
14BRN Braking resistor not included
14BRE Braking resistor, external
Enclosure Options
MCC Bottom
Support(1)(5)
XBC 1.5 inch high base channels
XBSM Bottom support angle multi-section
Options Available to All Units:
Option Option Code Description

PowerFlex® 700 and 700S Product Selection 1-5
(1) You must select (1) option from this group.
(2) All drives mounted in the same MCC vertical section must have option 111 if any one drive unit has option 111.
(3) You may select up to (1) option from this group.
(4) Pilot lights are Allen-Bradley® Bulletin 800M products and the pushbutton is an Allen-Bradley Bulletin 800T device.
(5) If one drive unit has base channels in any lineup, the entire lineup must have base channels. Base channels add 1.5 inches to the unit height.
(6) Option 6P is not available for drive units with voltage codes D, S, E, and F.
(7) Units with voltage codes D, S, E and F require horizontal power bus options. Only 800A, 1600A, and 3000A are available.
(8) You must select a ground bus option. If your lineup has a 3000A power bus, you must select the ground bus option for units with a 3000A-rated power bus.
(9) You must select a horizontal power bus option if you select a control bus.
(10) Units come standard with cloth wire labels. Datab labels offer the added protection of a clear plastic cover on top of the labels.
(11) Horizontal power bus is braced for 65kAIC.
(12) Maximum of 120 inches per shipping split.
(13) Requires an expended cassette for Phase II control.
(14) Available for Phase II control only. Requires an expanded cassette.
(15) For dual communications (DPI and DriveLogix) select the DriveLogix comm. option and order the DPI comm. kit separately.
(16) PowerFlex 700 frame 0 - 6 allows the “N” or “A” selections only. PowerFlex 700 frame 9 allows the “A” selection only. PowerFlex 700S frames 1 - 9 allows the “N” or “E” selections only.
(17) PowerFlex 700S only, requires an expanded cassette with Logix extras PCB.
(18) Required for PowerFlex 700S frames 1 - 6.
(19) Required for PowerFlex 700 frames 0 - 6 with voltages 380V AC, 460V AC, 575V AC, 512V DC, 620V DC, and 775V DC
(20) Required for PowerFlex 700 frames 0 - 2 with voltages 230V AC and 310 V DC
(21) You must select one (1) of these options for PowerFlex 700 frame 3 with voltages 230V AC and 310 V DC
(22) You must select one (1) of these options for PowerFlex 700S frame 9 with voltages 380V AC, 460V AC and 575V AC
(23) You must select one (1) of these options for PowerFlex 700S frame 9 with voltages 512V DC, 620V DC and 775V DC
Horizontal Power
Bus(3)(7)(9)(11)(12)
08-AC 800A AC power bus
08-DC 800A DC power bus
12-AC 1200A AC power bus
16-AC 1600A AC power bus
16-DC 1600A DC power bus
20-AC 2000A AC power bus
30-AC 3000A AC power bus
30-DC 3000A DC power bus
Ground Bus (PE/
TE)(1)(8)
XTEP2 PE/TE bus for unit with horizontal bus rated up to 2000A
XTEP3 PE/TE bus for unit with horizontal bus rated up to 3000A
115V AC Control
Bus(9)
X115 90A control bus
Top Hat 12 inch high top hat for extra entry cable bending radius
Options Available to All Units:
Option Option Code Description

1-6 PowerFlex® 700 and 700S Product Selection
Notes:

Chapter 2
1336 PLUS™ Variable Frequency, 1336 PLUS™ II,
1336 FORCE - Vector Control, 1336 IMPACT Product
Selection
Catalog Number
Explanation
Use the following tables for determining the catalog number used to order
1336 PLUS™ Variable Frequency, 1336 PLUS™ II, 1336 FORCE - Vector
Control, and 1336 IMPACT drives in Bulletin 2362 MCCs.
2362 S A - 4 A B - 48 DA -OPTIONS
Drive Type
E 1336S PLUS (AC Common Bus)
F 1336T FORCE (AC Common Bus)
G 1336S PLUS (DC Common Bus)
H 1336T FORCE (DC Common Bus)
L 1336E IMPACT (AC Common Bus)
M 1336E IMPACT (DC Common Bus)
N 1336E PLUS II (AC Common Bus)
P 1336E PLUS II (DC Common Bus)
Wiring Type
A“A”Type
B “A” Type Power Wiring with
Bottom Exit
T “A” Type Power Wiring with
Top Exi t
Frame Size
See Table 2.B on
page 2-3
Enclosure
A NEMA Type 1 with no
gaskets or door fan filters
J NEMA Type 1 with gaskets
or door fan filters
Input Voltages
A 230V AC Bus
N 380V AC Bus
B 460V AC Bus
C 575V AC Bus
D 310V DC Bus
S 512V DC Bus
E 620V DC Bus
F 775V DC Bus Horsepower Rating(3)
33 0.5
34 0.75
35 1.0
36 1.5
37 2.0
38 3.0
39 5.0
40 7.5
41 10
42 15
43 20
44 25
45 30
46 40
47 50
48 60
49 75
50 100
51 125
52 150
54 200
56 250
57 300
58 350
59 400
60 450
61 500
62 600
63 650
64 700
66 800
Disconnect Type
DA Fused Disconnect
Options
See Drive Unit Options on page 2-3

2-2 1336 PLUS™ Variable Frequency, 1336 PLUS™ II, 1336 FORCE - Vector Control, 1336 IMPACT Product Selection
Frame Selection The following table is used to determine the frame size required based on
the desired Drive Type, Input Voltage and Horsepower.
Table 2.A 1336 Frame Selection
1336 Frame Sizes
Drive
Type
Code Input Voltage
A
(1.5 SF
20” Wide)
B
(2.5 SF
20” Wide)
C
(3.5 SF
20” Wide)
D
(6.0 SF
20” Wide)
E
(6.0 SF
25” Wide)
F
(6.0 SF
35” Wide)
G
(6.0 SF
35” Wide)
H
(6.0 SF
35” Wide)
1336S PLUS
E230V AC 0.5 - 5.0 HP 7.5 - 15 HP 10 - 30 HP NA(1) NA NA NA NA
380/460V AC 0.5 - 5.0 HP 7.5 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP NA
575V AC 1, 3 HP 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP NA
G310V DC 0.5 - 5.0 HP 7.5 - 15 HP 10 - 30 HP NA NA NA NA NA
512/620V DC 0.5 - 5.0 HP 7.5 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP NA
775V DC 1, 3 HP 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP NA
1336T FORCE
F230V AC NA 1, 3, 7.5 - 15 HP 20 - 30 HP NA NA NA NA NA
380/460V AC NA 1, 3, 7.5 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP NA
575V AC NA 1, 3, 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP NA
H310V DC NA 1, 3, 7.5 - 15 HP 20 - 30 HP NA NA NA NA NA
512/620V DC NA 1, 3, 7.5 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP 700, 800 HP
775V DC NA 1, 3, 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP 700, 800 HP
1336E IMPACT
L230V AC 0.5 - 5.0 HP 7.5 - 15 HP 10 - 30 HP NA NA NA NA NA
380/460V AC 0.5 - 5.0 HP 7.5 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP NA
575V AC 1, 3 HP 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP NA
M310V DC 0.5 - 5.0 HP 7.5 - 15 HP 10 - 30 HP NA NA NA NA NA
512/620V DC 0.5 - 5.0 HP 7.5 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP 700, 800 HP
775V DC 1, 3 HP 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP 700, 800 HP
A
(1.5 SF <= 5 HP
2.5 SF >5 HP
20” Wide)
B
(2.5 SF
20” Wide)
C
(3.5 SF
20” Wide)
D
(6.0 SF
20” Wide)
E
(6.0 SF
25” Wide)
F
(6.0 SF
35” Wide)
G
(6.0 SF
35” Wide)
H
(6.0 SF
35” Wide)
1336F PLUS II
N230V AC 0.5 - 5.0 HP 7.5 - 15 HP 20 - 30 HP NA NA NA NA NA
380/460V AC 0.5 - 15 HP 20 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP NA
575V AC 0.5 - 20 HP 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP NA
P310V DC 0.5 - 5.0 HP 7.5 - 15 HP 20 - 30 HP NA NA NA NA NA
512/620V DC 0.5 - 15 HP 20 - 30 HP 40 - 50 HP 60 - 125 HP 150 - 250 HP 300 - 400 HP 450 - 600 HP NA
775V DC 0.5 - 20 HP 7.5 - 20 HP 25 - 60 HP 75 - 125 HP 150 - 300 HP 350 - 400 HP 450 - 650 HP NA
(1) NA = Not Available

1336 PLUS™ Variable Frequency, 1336 PLUS™ II, 1336 FORCE - Vector Control, 1336 IMPACT Product Selection 2-3
Drive Unit Options Table 2.B Drive Unit Options
Options Available to All Units:
Option Option Code Description
Control Power
Source(1)(6)
6P Individual 115V AC-secondary, control power transformer (supplied per drive unit). Includes primary fusing
6TB 115V AC control power, factory wired from 115V AC control bus to drive unit (requires control bus)
6SC 115V AC control power supplied by customer
Auxiliary Contact
for
Disconnect(3)(5)
Input Voltage >
Frame Size >
230V AC /
310V DC
380V AC /
460V AC
512V DC /
620V DC
575V AC 775V DC
A,B,C A,B,C,D,E F,G,H A,B,C,D,E F,G,H
98 (1) normally open (Y = option avail.) Y Y Y
99 (1) normally closed (Y = option avail.) Y Y Y
989 (1) normally open + (1) normally closed (Y = option
avail.)
YY
Wire Label
Upgrade
Option(11)
14WLBL Brady Datab™ wire labels
T-Handles(2) 111 T-handles on doors and 3” vertical wireway (present in MCC sections containing frame A, B, & C drive units
Door-Mounted
Devices(4)
1ES Hardwired-interface-stop-pushbutton; for drive-disable function
4EA Control-power-on pilot light
4EB Drive-at-speed pilot light
4ER Drive-run pilot light
4EW Drive-faulted pilot light
Miscellaneous J11 Audio phone jack
J12 115V AC, 15A, duplex receptacle
Unit Door
Nameplates(1)
M3EW Phenolic label with white background and black lettering
N3EB Phenolic label with black background and white lettering
N3ER Phenolic label with red background and white lettering
Communication
Adapters(3)
14CN1 DPI - SCANport™ to ControlNet adapter
14G1 SCANport to Single-Point Remote I/O (RIO) adapter
14G2 SCANport to RS232/422/485, DF1, or DH485 adapter
14G5 SCANport to DeviceNet adapter
Human Interface
Module (HIM)(3)
14HA1C Door-mounted HIM with analog potentiometer
14HA2C Door-mounted HIM with digital potentiometer
14HAPC Door-mounted HIM, Programmer Only LCD
14HNBC Door-mounted connector permitting connection of a hand-held HIM or GPT through closed-door unit
Options Available to 2362E & 2362G Units:
Option Option Code Description
Control Logic
Interface
Boards(3)
14L5 24V DC
14L5E 24V DC with encoder feedback
14L6 115V AC
14L6E 115V AC with encoder feedback
Languages(1) 14DE English/German
14EN English/English
14ES English/Spanish
14FR English/French
14IT English/Italian

2-4 1336 PLUS™ Variable Frequency, 1336 PLUS™ II, 1336 FORCE - Vector Control, 1336 IMPACT Product Selection
Options Available to 2362F & 2362H Units:
Option Option Code Description
Control Logic
Interface
Boards(3)
14L5 24V DC
14L6 115V AC
Drive Adapter
Boards(1)
14CN ControlNet (version 1.5) Adapter
14PCA PLC Comm Adapter
14SA Standard Adapter (If you selected Control Logic Interface Board 14L5 or 14L6, you must choose this Drive
Adapter Board.)
Languages(1) 14EN English/English
14ES English/Spanish
14FR English/French
Options Available to 2362L & 2362M Units:
Option Option Code Description
Control Logic
Interface
Boards(3)
14L5 24V DC
14L6 115V AC
14L8E 24V DC with encoder feedback and encoder loss detection
14L9E 115V AC with encoder feedback and encoder loss detection
Languages(1) 14DE English/German
14EN English/English
14ES English/Spanish
14FR English/French
14IT English/Italian
Options Available to 2362N & 2362P Units:
Option Option Code Description
Control Logic
Interface Boards(3)
14L5 24V DC
14L5E 24V DC with encoder feedback
14L6 115V AC
14L6E 115V AC with encoder feedback
14L8E 24V DC with encoder feedback and encoder loss detection
14L9E 115V AC with encoder feedback and encoder loss detection
Analog Interface
Board Port A(3)
14LA2 = (2) isolated, configurable inputs
14LA6 = (3) non-isolated, thermistor/RTD inputs
14LA7 = (1) isolated, bipolar input (+/- 10V and (1) isolated, configurable input
Port B(3)
14LA1 = (1) single-ended, non-isolated, configurable input OR (1) potentiometer & (2) single-ended,
non-isolated, 1-to-20mA outputs
14LA3 = (2) isolated, configurable outputs
14LA4 = (1) isolated, configurable input and output
14LA5 = (1) isolated, pulse input and output & (1) single-ended, non-isolated, 0-to-10V output

1336 PLUS™ Variable Frequency, 1336 PLUS™ II, 1336 FORCE - Vector Control, 1336 IMPACT Product Selection 2-5
(1) You must select (1) option from this group.
(2) All drives mounted in the same MCC vertical section must have option 111 if any one drive unit has option 111.
(3) You may select up to (1) option from this group.
(4) Pilot lights are Allen-Bradley® Bulletin 800M products and the pushbutton is an Allen-Bradley Bulletin 800T device.
(5) If one drive unit has base channels in any lineup, the entire lineup must have base channels. Base channels add 1.5 inches to the unit height.
(6) Option 6P is not available for drive units with voltage codes D, S, E, and F.
(7) If you are connecting to an FD86N cabinet, you must select base channels and enclosures that are 20 inches and/or 25 inches deep.
(8) Units with voltage codes D, S, E and F require horizontal power bus options. Only 800A, 1600A, and 3000A are available.
(9) You must select a ground bus option. If your lineup has a 3000A power bus, you must select the ground bus option for units with a 3000A-rated power bus.
(10) You must select a horizontal power bus option if you select a control bus.
(11) Units come standard with cloth wire labels. Datab labels offer the added protection of a clear plastic cover on top of the labels.
(12) If at least one unit in a lineup is 20 inches or 25 inch deep flush back, then all other drive units in that lineup must be 20 inches or 25 inches deep.
(13) If the drive unit is mounted in a 25 inch deep flush front enclosure, you must select a 3000A horizontal power bus for that unit. If you have drives mounted in 15 inch or 20 inch deep sections
in the same lineup, you may select a different horizontal power bus option; but all non-25 inch deep enclosure units in a lineup must have the same horizontal power bus option. The
horizontal power bus rating of the entire lineup equals the lowest power bus rating selected.
(14) Horizontal power bus is braced for 65kAIC.
(15) Maximum of 120 inches per shipping split.
(16) Horizontal power bus and control bus (if selected) are mounted at a depth of 11.94 inches in all MCC sections containing frame A, B, and C drive units, regardless of section depth. Frame
D, E, F, G, and H drives units have power bus and control bus (if selected) mounted at a depth of 16.94 inches or greater with bus ends for splicing always at a depth of 16.94 inches. Select
offset splice kit(s) when shipping split requires splicing bus ends at a depth of 11.94 inches to bus ends at a depth of 16.94 inches. If both sections have bus ends at the same depth, select
straight splice kits. Use the tables in the Power Bus Splice Kit Catalog Numbers section on page 4-1 to select splice splits per shipping split.
(17) Frame F, G, and H drive units require top hats if input power is not supplied by a power bus option.
(18) Requires an expended cassette for Phase II control.
(19) Available for Phase II control only. Requires an expanded cassette.
(20) For dual communications (DPI and DriveLogix) select the DriveLogix comm. option and order the DPI comm. kit separately.
Enclosure Options Available to All Units:
Option Description
Section
Depth(7)(12)
Input Voltage > 230V AC 380/460V AC 575V AC 310V DC 512V/620V DC 775V DC
Frame Size >
A, B, C A, B, C
D, E
F, G
A, B, C
D, E
F, G
A, B, C A, B, C
D, E, F
G, H
A, B, C
D, E, F
G, H
15” deep MCC (Y = option avail.) Y Y Y Y Y Y
20” deep MCC (Y = option avail.) Y Y Y Y Y Y Y Y Y Y
25” deep MCC (Y = option avail.) Y Y Y Y
1.5 Inch High
Base
Channels(5)(7)
Required (R) or Optional (O): O O O R O O R O O O R O O R
Horizontal Power
Bus(8)(13)(14)(15)
(16)
Input Voltage > 230V AC
380V AC
460V AC
575V AC
310V DC
512V DC
620V DC
775V DC
800A (Y = option avail.) Y Y
1200A (Y = option avail.) Y
1600A (Y = option avail.) Y Y
2000A (Y = option avail.) Y
3000A (Y = option avail.) Y Y
Ground Bus (PE/
TE)(9)(16)
PE/TE bus for unit with horizontal power bus rated up to 2000A
PE/TE bus for unit with horizontal power bus rated up to 3000A
115V AC Control
Bus(10)(16)
90A control bus
Top Hat(17) 12” high top hat for extra entry cable bending radius

2-6 1336 PLUS™ Variable Frequency, 1336 PLUS™ II, 1336 FORCE - Vector Control, 1336 IMPACT Product Selection
Notes: