Allen-Bradley SLC 500 User manual

Addressing
Reference
Manual
SLC 500tFamily
of Programmable
Controllers
Allen-Bradley

2
Because of the variety of uses for the products described in this
publication, those responsible for the application and use of this control
equipment must satisfy themselves that all necessary steps have been taken
to assure that each application and use meets all performance and safety
requirements, including any applicable laws, regulations, codes and
standards.
The illustrations, charts, sample programs and layout examples shown in
this guide are intended solely for purposes of example. Since there are
many variables and requirements associated with any particular
installation, Allen-Bradley does not not assume responsibility or liability
(to include intellectual property liability) for actual use based upon the
examples shown in this publication.
Allen-Bradley publication SGI–1.1, Safety Guidelines for the Application,
Installation, and Maintenance of Solid-State Control (available from your
local Allen-Bradley office), describes some important differences between
solid-state equipment and electromechanical devices that should be taken
into consideration when applying products such as those described in this
publication.
Reproduction of the contents of this copyrighted publication, in whole or
in part, without written permission of Allen-Bradley company, Inc., is
prohibited.
Throughout this manual we use notes to make you aware of safety
considerations.
ATTENTION: Identifies information about practices or
circumstances that can lead to personal injury or death, property
damage or economic loss.
Attention statements help you to:
identify a hazard
avoid the hazard
recognize the consequences
Important: Identifies information that is critical for successful application
and understanding of the product.
Important User Information

1
Data Table Addressing for the SLC 500t
Family of Processors
This addressing reference helps you specify data table addresses in
SLC 500tfixed and modular programmable controllers. It contains
information for the following processors:
all SLC 500 Fixed Programmable Controllers
The following SLC 500 Modular Programmable Controllers
- SLC 5/01 CPU
- SLC 5/02 CPU
- SLC 5/03 CPU
Locating Addressing Information
For information about See page
memory maps 3
general format for direct logical ASCII addressing 4
logical addressing for I/O image elements 5
logical addressing for the status elements 7
logical addressing for integer elements 9
logical addressing for binary elements 11
logical addressing for floating-point elements 13
logical addressing for timer structures 14
logical addressing for counter structures 16
logical addressing for control block structures 18
Introduction

Addressing Reference
SLC 500 Family of Programmable Controllers
2
For specific information about the content of data table files, consult the:
PLCprogrammer, who assigns data to specific memory locations
SLC 500 Fixed Hardware Style Installation and Operation Manual,
publication 1747–NI001.
SLC 500 Modular Hardware Style Installation and Operation Manual,
publication 1747–NI002.
Advanced Programming Software (APS) User’s Manual,
publication 1747–NM002.
Important: Throughout this publication we use $as the logical address
identifier. This is an entry for INTERCHANGE software. It is also an entry
for 6200 programming software in sending a message from other stations
to a SLC 500 processing station. It is not used in 6200 programming
software for internal addressing.

Addressing Reference
SLC 500 Family of Programmable Controllers
3
Table A shows the logical arrangement of the data table for SLC 500
processors.
T able A
Data T able Memory Map
OUTPUT IMAGE
INPUT IMAGE
STATUS
BINARY
TIMER
COUNTER
CONTROL
INTEGER
FLOATING–POINT
$O:0
$O:30
$I:0
$I:30
$S:0
$S:n
$B3:0
$B3:255
$T4:0
$T4:255
$C5:0
$C5:255
$R6:0
$R6:255
$N7:0
$N7:255
$F8:0
$F8:255
$x10:0
$x255:255
NETWORK
USER DEFINED
File
Number File Type Logical Address Comments
$x9:0
$x9:255
See Note 1
See Note 2
See Note 3
See Note 4
0
1
2
3
4
5
6
7
8
9
10
thru
255
to
to
to
to
to
to
to
to
to
to
to
Notes
1 Address range is processor specific; see Logical Addressing for the Status Elements section.
2 Only the SLC 5/03 series B processor supports floating-point data type. Do not use this area for
processors that do not support floating-point data.
3 If non SLC 500 devices exist on the DH-485 link, use this area for network transfer. You can use
either binary (B) or integer (N) file types by specifying the appropriate letter for x. Otherwise, you can
use file 9 for user-defined files.
4 Use this area when you need more binary, timer, counter, control, integer, floating-point, or network
files that will fit in the reserved files. You can use binary (B), timer (T), counter (C), control (R), integer
(N), floating-point (F), or transfers (B and/or N) file types by specifying the appropriate letter for
x . You
cannot use this area for output image, input image, and/or status files.
Memory Map

Addressing Reference
SLC 500 Family of Programmable Controllers
4
Figure 1 illustrates the general format for logical addressing in the data
table.
Figure 1
General Format for Logical Addressing
File Type
A = ASCII
B = Binary
C = Counter
D = Decimal (BCD)
F = Floating-point2
I = Input
N = Integer
O = Output
R = Control Block
S = Status
ST = ASCII String2
T = Timer
File Number
0 = Output
1 = Input
2 = Status
3 = Binary
4 = Timer
5 = Counter
6 = Control Block
7 = Integer
8 = Floating-point
10-255 = User-defined
Bit Number
0 – 15 decimal
Element or Structure Number
0 – 255 for all files except Status1
Logical Address Identifier
File Separator
Bit Separator (if addressing a bit)
$ B 123 : 123 / 15
Notes:
1The number of elements (words) in the status file is processor dependent;
see Logical Addressing for the Status Element section.
2ASCII string, floating-point, and network file types are not available on
SLC 500, SLC 5/01, SLC 5/02, SLC 5/03 processors.
You can address individual bits for the following elements in a data table
file by absolute bit number (0 thru 4095):
binary
control block
input image
integer
output image
status
General Format for Logical
ASCII Addressing

Addressing Reference
SLC 500 Family of Programmable Controllers
5
The file for output image elements is file 0 of the data table. This file
accommodates up to 256 output image elements.
The file for input image elements is file 1 of the data table. This file
accommodates up to 256 input image elements.
Each I/O image element consists of one 16-bit word. You can address an
I/O image element in its entirety of you can address any particular input or
output bit of an element individually.
Figure 2
Logical Addressing for I/O Image Elements
File Type
O = Output
I = Input
I/O Slot Number
0 – 30 decimal
Bit Number**
0 – 15 decimal
Word Number**
0 – 255 decimal
Logical Address Identifier
File Separator
Bit Separator**
$ I : 12 . 1 / 12
Word Separator**
* Required only when addressing to the bit level.
** Required only when addressing 24- and 32-bit I/O.
Figure 3
Bit Map of I/O Image Element for 8-bit Discrete I/O
151413121110987654321 0
X = Not Used
XXXXXXXX7654321 0 I/O Bit Number
Figure 4
Bit Map of I/O Image Element for 16-bit Discrete I/O
151413121110987654321 0
7654321 0 I/O Bit Number
14 13 12 11 10 9 815
Logical Addressing for the
Input/Output Image
Elements

Addressing Reference
SLC 500 Family of Programmable Controllers
6
Figure 5
Bit Map of I/O Image Element for 24-bit Discrete I/O
151413121110987654321 0
7654321 0 I/O Bit Number
14 13 12 11 10 9 815
X X X X X X X X 23 22 21 20 19 18 17 16 I/O Bit Number
W
ord 0
W ord 1
Figure 6
Bit Map of I/O Image Element for 32-bit Discrete I/O
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
7654321 0 I/O Bit Number
14 13 12 11 10 9 815 23 22 21 20 19 18 17 16
30 29 28 27 26 25 2431 I/O Bit Number
W
ord 0
W ord 1
T able B
Parameters of I/O Elements
Description PLC Data Type Valid Range
Input Element signed word –32,768 thru +32,767
Output Element signed word –32,768 thru +32,767
T able C
Examples for I/O Element 3 in Slot 5
To address the Use this form
Entire Input Element $I:5.3
Input Bit 6 $I:5.3/6
Entire Output Element $O:5.3
Output Bit 6 $O:5.3/6

Addressing Reference
SLC 500 Family of Programmable Controllers
7
The file for status elements is file 2 of the data table. The number of status
elements in this file (n) is processor dependent, see Figure 8.
Figure 7
Logical Addressing for Status Elements
Bit Number*
0 – 15 decimal
Word Number
0 – n decimal
Logical Address Identifier
File Separator
Bit Separator*
$ S : 12 / 12
*Required only when addressing to the bit level..
File Type
S = Status
For specific information about status elements, refer to the Advanced
Programming Software (APS) User’s Manual, publication 1747-NM002.
T able D
Parameters of Status W ords
Description PLC Data Type Valid Range
Status Element signed word –32,768 thru +32,767
T able E
Examples for Status Element 3 in the Default File (File 2)
To address the Use this form
Entire Element $S:3 or $S2:3
Tenth Data Bit $S:3/9 or $S2:3/9
Logical Addressing for the
Status Elements

Addressing Reference
SLC 500 Family of Programmable Controllers
8
Figure 8
Status file Memory Map for SLC Processors
1
Word Description Word Description
0Arithmetic and Scan Stat Flags 42 Time-of-Day Seconds
1Processor Mode, Status, and Control 43 Reserved
2Processor Alternate Mode, Status, and Control 44 Reserved
3Current and Watchdog Scan Timers 45 Reserved
4 Timebase 46 DII File Number
5Minor Error Bits 47 DII Input Slot
6Major Error Bits 48 DII Mask
7Suspend Code 49 DII Compare Value
8Suspend File 50 DII Down Count
9Network – Active Node Table word 0 51 DII Return Mask
10 Network – Active Node Table word 1 52 DII Accumulator
11 I/O Slot Enable/Disable Flags word 0 53 Reserved
12 I/O Slot Enable/Disable Flags word 1 54 Reserved
13 Math Register word 0 55 Last DII ISR Scan Time
14 Math Register word 1 56 Maximum DII ISR Scan Time
15 Node Address and Baud Rate 57 Processor Operating System Catalog Number
16 Test Single Step – Start at Rung Number 58 Processor Operating System System Series
17 Test Single Step – Start at File Number 59 Processor Operating System Release Number
18 Test Single Step – Stop Before Rung Number 60 Hardware Catalog Number
19 Test Single Step – Stop Before File Number 61 Hardware Series
20 Test Report – Fault/Powerdown Rung Number 62 Hardware Revision
21 Test Report – Fault/Powerdown File Number 63 User Program Type
22 Maximum Observed Scan Time 64 User Program Functional Index
23 Average Scan Time 65 User RAM Size
24 Index Register 66 Flash EEPROM Size
25 I/O Interrupt Pending word 0 67 Channel 0 Active Node Table word 0
26 I/O Interrupt Pending word 1 68 Channel 0 Active Node Table word 1
27 I/O Interrupt Enabled word 0 69 Channel 0 Active Node Table word 2
28 I/O Interrupt Enabled word 1 70 Channel 0 Active Node Table word 3
29 User Fault Routine File Number 71 Channel 0 Active Node Table word 4
30 STI (selectable timed interrupt) Time Interval 72 Channel 0 Active Node Table word 5
31 STI (selectable timed interrupt) File Number 73 Channel 0 Active Node Table word 6
32 I/O Interrupt Executing 74 Channel 0 Active Node Table word 7
33 Extended Processor Mode, Status, and Control 75 Channel 0 Active Node Table word 8
34 Reserved 76 Channel 0 Active Node Table word 9
35 Current Scan Time 1 msec 77 Channel 0 Active Node Table word 10
36 Extended Minor Error Bits 78 Channel 0 Active Node Table word 11
37 Calendar Year 79 Channel 0 Active Node Table word 12
38 Calendar Month 80 Channel 0 Active Node Table word 13
39 Calendar Day 81 Channel 0 Active Node Table word 14
40 Time-of-Day Hours 82 Channel 0 Active Node Table word 15
41 Time-of-Day Minutes
1 Not all processors support all status words. SLC 500 and SLC 5/01 processors only support words 0 – 15. SLC 5/02 processors only support words 0 – 32.
SLC 5/03 processors support words 0 – 82