Allen-Bradley PowerFlex 755 IP00 User manual

Installation Instructions
Original Instructions
PowerFlex 755 IP00, NEMA/UL Open Type Drive Frames 8…10
Catalog Numbers 200…1500 kW (250…2000 Hp)
This document provides instructions for the installation of an IP00, Open Type PowerFlex® 755 drive (Frames 8…10) in
a user supplied enclosure.
The information provided in this publication supplements the PowerFlex 750-Series AC Drives Installation Instructions,
publication 750-IN001, and is intended for qualified drive service personnel only.
Topic Page
Summary of Changes 2
General Precautions 2
Certifications 3
Overview 4
Installation Overview 6
AC Input Drives 8
Common DC Input Drives 12
Installation Tools 16
Enclosure Requirements 16
CE Conformity 23
Horizontal Mounting Guidelines – Single Drive Unit Only 26
Dimensions 28
Lifting 36
Drive Installation 38
Selecting/Verifying Control Transformer Voltage 41
Installing the Control Pod in the Drive 42
Power Wiring 45
Kit Installation Guidelines 49
Cable Routing 58
I/O Wiring 59
Fuse and Circuit Breaker Ratings 67
Additional Resources 76

2Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Summary of Changes This publication contains new and updated information as indicated in the
following table.
General Precautions Qualified Personnel
Personal Safety
Topic Page
Removed the footnote from Table G. 5
Corrected catalog numbers in the AC Input Drive Installation Kits table,
corrected footnote 8, and added footnote 9. 10
Corrected catalog numbers in the Common DC Input Drive Installation Kits
table, corrected footnote 6, and added footnote 7. 14
Updated the Additional Resources table. 76
ATTENTION: Only qualified personnel familiar with adjustable frequency AC
drives and associated machinery should plan or implement the installation,
start-up and subsequent maintenance of the system. Failure to comply may
result in personal injury and/or equipment damage.
ATTENTION: To avoid an electric shock hazard, ensure that all power to the
drive has been removed before proceeding. In addition, before servicing, verify
that the voltage on the bus capacitors has discharged. Measure the DC bus
voltage on Frame 8 drives at the DC+ and DC- TESTPOINT sockets on the front of
the power module (see page 47). The voltage must be zero.
ATTENTION: Hazard of personal injury or equipment damage exists when
using bipolar input sources. Noise and drift in sensitive input circuits can cause
unpredictable changes in motor speed and direction. Use speed command
parameters to help reduce input source sensitivity.
ATTENTION: Risk of injury or equipment damage exists. DPI™ or SCANport™
host products must not be directly connected together via 1202 cables.
Unpredictable behavior can result if two or more devices are connected in this
manner.
ATTENTION: The drive start/stop/enable control circuitry includes solid state
components. If hazards due to accidental contact with moving machinery or
unintentional flow of liquid, gas or solids exists, an additional hardwired stop
circuit may be required to remove the AC line to the drive. An auxiliary braking
method may be required.

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 3
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Personal Safety (continued)
Product Safety
Class 1 LED Product
Certifications See the PowerFlex 750-Series AC Drives Technical Data, publication
750-TD001, for detailed specifications and certifications.
ATTENTION: Hazard of personal injury or equipment damage due to
unexpected machine operation exists if the drive is configured to automatically
issue a Start or Run command. Do not use these functions without considering
applicable local, national and international codes, standards, regulations or
industry guidelines.
ATTENTION: An incorrectly applied or installed drive can result in component
damage or a reduction in product life. Wiring or application errors such as under
sizing the motor, incorrect or inadequate AC supply, or excessive surrounding air
temperatures may result in malfunction of the system.
ATTENTION: This drive contains ESD (Electrostatic Discharge) sensitive parts
and assemblies. Static control precautions are required when installing, testing,
servicing or repairing this assembly. Component damage may result if ESD
control procedures are not followed. If you are not familiar with static control
procedures, reference Guarding Against Electrostatic Damage, publication
8000-4.5.2 or any other applicable ESD protection handbook.
ATTENTION: Configuring an analog input for 0-20 mA operation and driving it
from a voltage source could cause component damage. Verify proper
configuration prior to applying input signals.
ATTENTION: A contactor or other device that routinely disconnects and
reapplies the AC line to the drive to start and stop the motor can cause drive
hardware damage. The drive is designed to use control input signals that will
start and stop the motor. If an input device is used, operation must not exceed
one cycle per minute or drive damage will occur.
ATTENTION: Hazard of permanent eye damage exists when using optical
transmission equipment. This product emits intense light and invisible
radiation. Do not look into module ports or fiber optic cable connectors.
IMPORTANT
To meet UL certification, the Field Termination and Control Pod kits described
on page 10 or page 14 must be used.

4Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Overview Selecting and Integrating an IP00 System
The following steps will guide you in planning and installing a PowerFlex 755
IP00, NEMA/UL Open Type drive.
1. Considerations
•Drive size (Hp & V AC), required accessories/options (HIM, comms, etc.)
•Ingress protection of system
•Mounting orientation of drive
•Cooling method, venting orientation, alignment of venting
•Control pod mounting location
•Cabling entry/exit scheme and cable routing provisions
•Roll-out cart required
•Personnel safety and necessary tooling
2. Selection
•Select and purchase enclosure with sub-panel and ingress accessories (page 16)
•Select and purchase drive and corresponding drive options (see 750-TD001)
•Select and purchase pod and corresponding cables (page 10 or page 14)
•Select and purchase field termination kits (page 10 or page 14)
•Select and purchase appropriate mounting kits (drive mounting & floor - page 10
or page 14)
•Select and purchase door fans (pages 20…21)
•Select and purchase necessary wire and cabling (pages 45 & 59)
3. Prepare the Enclosure
•Create ventilation openings, mount door fans (pages 17…21)
•Provisions for accessories (HIM cradle, etc. - see 750-TD001)
•Fabricate and mount inlet and outlet plenums (pages 17…19)
•Drill sub-panel(s) (page 39 & page 40)
•Mount field termination kit, mounting brackets, and floor kit (page 39 & page 40)
•Mounting of customer specified accessories
•Remote mounting of control pod (if specified - see 750-IN015)
•Mount sub-panel(s)
4. Power and Ground Wiring
•Ensure proper grounding (page 45)
•Position & secure movable L-brackets (page 49)
•Properly terminate power cables (page 48)
•Attach power cabling (page 48)
5. Roll-in and Secure the Drive Unit
•Raise drive unit to vertical orientation (page 37)
•Position roll-out cart (see 750-IN001)
•Lift drive unit onto cart (see 750-IN001)
•Roll drive unit into cabinet and secure (see 750-IN001)
6. Control Wiring
•Mount control pod into drive (if specified - page 42)
•Verify control transformer voltage (page 41)
•Ensure proper cable routing (page 58)
•Attach pod power and fiber optic cables (page 58)
•Install real time clock battery and HIM cable (page 60)
•Install remaining control wiring (pages 59…66)
•Verify correct torque on all fasteners and connectors
7. Commission the System

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 5
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Catalog Number Explanation
Position
1…345678…10 11 12 13 14 1516 17 18
20G 1 1 T D 485 A N 0 N NNNN
a b c d e f1…f2 g h
a
Drive
Code Type
20G PowerFlex 755
b
Future Use
c
Input Type
Code Description
1 AC Input w/Precharge
4 DC Input w/Precharge
d
Enclosure
Code Description
T IP00, UL Open Type without Control POD
e
Voltage Rating
Code Voltage
C 400V AC / 540V DC
D 480V AC / 650V DC
E 600V AC / 810V DC
F 690V AC / 932V DC (not UL listed)
f1
ND Rating
400V AC / 540V DC, 50 Hz Input
Code Amps kW Quantity
Required
Equivalent
Frame Size
C460 460 250 1
8
C540 540 315 1
C567 567 315 1
C650 650 355 1
C750 750 400 1
C770 770 400 1
C460 910 500 2
9
C540 1040 560 2
C567 1090 630 2
C650 1175 710 2
C750 1465 800 2
C770 1480 850 2
C567 1590 900 3 10
C770 2150 1250 3
To achieve the extended ratings listed for Frames 9 and 10, the base
Frame 8 drive must be paralleled 2 or 3 times. Refer to the Drive
Rating tables on pages 8, 9, 12, and 13 for detailed information.
f2
ND Rating
480V AC / 650V DC, 60 Hz Input
Code Amps Hp Quantity
Required
Equivalent
Frame Size
D430 430 350 1
8
D485 485 400 1
D545 545 450 1
D617 617 500 1
D710 710 600 1
D740 740 650 1
D430 800 700 2
9
D485 960 800 2
D545 1045 900 2
D617 1135 1000 2
D710 1365 1100 2
D740 1420 1250 2
D545 1525 1350 3 10
D740 2070 1750 3
To achieve the extended ratings listed for Frames 9 and 10, the base
Frame 8 drive must be paralleled 2 or 3 times. Refer to the Drive
Rating tables on pages 8, 9, 12, and 13 for detailed information.
f3
ND Rating
600V AC / 810V DC, 60 Hz Input
Code Amps Hp Quantity
Required
Equivalent
Frame Size
E295 295 300 1
8
E355 355 350 1
E395 395 400 1
E435 435 450 1
E460 460 500 1
E510 510 500 1
E295 595 600 2
9
E355 630 700 2
E395 760 800 2
E435 825 900 2
E460 900 950 2
E510 980 1000 2
E395 1110 1100 3 10
E510 1430 1400 3
To achieve the extended ratings listed for Frames 9 and 10, the base
Frame 8 drive must be paralleled 2 or 3 times. Refer to the Drive
Rating tables on pages 8, 9, 12, and 13 for detailed information.
f4
ND Rating
690V AC / 932V DC, 60 Hz Input (not UL listed)
Code Amps kW Quantity
Required
Equivalent
Frame Size
F265 265 250 1
8
F330 330 315 1
F370 370 355 1
F415 415 400 1
F460 460 450 1
F500 500 500 1
F265 590 560 2
9
F330 650 630 2
F370 710 710 2
F415 765 750 2
F460 795 800 2
F500 960 900 2
F370 1040 1000 3 10
F500 1400 1400 3
To achieve the extended ratings listed for Frames 9 and 10, the base
Frame 8 drive must be paralleled 2 or 3 times. Refer to the Drive
Rating tables on pages 8, 9, 12, and 13 for detailed information.
g
Filtering and CM Cap Conguration
Code Filtering Default CM Cap Connection
A Yes Jumper Removed
J Yes Jumper Installed
h
Dynamic Braking §
Code Internal Resistor Internal Transistor
NNo No
§Not available on Frames 8…10.

6Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Installation Overview AC Input Drives
A typical IP00 installation for an AC input drive is shown below. See pages 8…10
for available kits and ratings.
PE
PE
PE
PE
PE
PE
R/L1
S/L2
T/L3
DC(+)
DC(+)
DC(-)
DC(-)
DC
(+)
DC
(-)
U/T1
V/T2
W/T3
PE
PE
Power
755
Converter (ACInput)
Termination Kit
Sub Panel
(for reference only)
IP00 Frame 8 Drive Assembly
(Inverter & Converter)
Mounting Kit
Inverter (DC Bus)
Termination Kit
Optional for a Frame 8
equivalent. Use only if the
application requires.
Inverter (AC Output)
Termination Kit
Mounting Kit
Outlet Ducting Kit
Floor Mounting
Kit
Roll-out Cart
Bottom Duct Kit
Bottom inlet duct mounts inside
of the Floor Mounting kit. Both
kits are required for inlet ducting
from the bottom.
Control Pod
For drive mounting, see page 42.
See publication 750-IN015 for
remote mounting information.

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 7
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Common DC Input Drives
A typical IP00 installation for a common DC input drive is shown below. See
pages 12…14 for available kits and ratings.
PE
PE
Power
755
Control Pod
For drive mounting, see page 42.
See publication 750-IN015 for
remote mounting information.
IP00 Frame 8 Common DC
Input Drive Assembly
(w/Precharge)
Sub Panel
(for reference only)
Control Transformer
Overload Protection
required for Common DC
Input drives, see page 20
Mounting Kit
DC Input for
Common Bus
Precharge
Termination Kit
Inverter (AC Output)
Termination Kit
Mounting Kit
Outlet Ducting Kit
Floor Mounting
Kit
Roll-out Cart
Bottom Duct Kit
Bottom inlet duct mounts inside
of the Floor Mounting kit. Both
kits are required for inlet ducting
from the bottom.

8Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
AC Input Drives Drive Ratings
The following tables provide rating and selection information for the PowerFlex
755 IP00 NEMA/UL Open Type AC input drives.
380…480V AC, Three-Phase, 50 Hz Input
Three-Phase, 0…400 Hz Output
480V AC, Three-Phase, 60 Hz Input
Three-Phase, 0…400 Hz Output
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kWCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V AC
534 540 594 NA 315 455 460 506 693 250 380 385 578 693 200 360…440 20G11TC460 1 8
578 585 644 315 533 540 594 821 315 450 456 684 821 250 360…440 20G11TC540 1 8
604 612 673 355 560 567 624 851 315 466 472 708 851 250 360…440 20G11TC567 1 8
739 750 825 400 640 650 715 975 355 533 540 810 975 315 360…440 20G11TC650 1 8
784 796 876 450 739 750 825 1125 400 577 585 878 1125 315 360…440 20G11TC750 1 8
819 832 915 450 758 770 847 1155 400 634 642 963 1155 355 360…440 20G11TC770 1 8
1024 1040 1144 560 896 910 1001 1365 500 739 750 1125 1365 400 360…440 20G11TC460 2 9
1073 1090 1199 630 1024 1040 1144 1584 560 867 880 1320 1584 500 360…440 20G11TC540 2 9
1157 1175 1293 710 1073 1090 1199 1638 630 896 910 1365 1638 500 360…440 20G11TC567 2 9
1443 1465 1612 800 1157 1175 1293 1872 710 1024 1040 1560 1872 560 360…440 20G11TC650 2 9
1457 1480 1628 850 1443 1465 1612 2198 800 1073 1090 1635 2198 630 360…440 20G11TC750 2 9
1576 1600 1760 900 1457 1480 1628 2220 850 1157 1175 1763 2220 710 360…440 20G11TC770 2 9
1689 1715 1887 1000 1566 1590 1749 2385 900 1305 1325 1988 2385 710 360…440 20G11TC567 3 10
2294 2330 2563 1400 2117 2150 2365 3225 1250 1773 1800 2700 3225 1000 360…440 20G11TC770 3 10
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
HpCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V AC
458 485 534 NA 400 406 430 473 666 350 349 370 555 666 300 432…528 20G11TD430 1 8
514 545 600 450 458 485 534 745 400 391 414 621 745 350 432…528 20G11TD485 1 8
557 590 649 500 514 545 600 818 450 428 454 681 818 350 432…528 20G11TD545 1 8
670 710 781 600 582 617 679 926 500 458 485 728 926 400 432…528 20G11TD617 1 8
722 765 842 650 670 710 781 1065 600 514 545 818 1065 450 432…528 20G11TD710 1 8
755 800 880 700 698 740 817 1110 650 582 617 926 1110 500 432…528 20G11TD740 1 8
906 960 1056 800 755 800 880 1278 700 670 710 1065 1278 600 432…528 20G11TD430 2 9
986 1045 1150 900 906 960 1056 1440 800 750 795 1193 1440 700 432…528 20G11TD485 2 9
1071 1135 1249 1000 986 1045 1150 1568 900 755 800 1200 1568 750 432…528 20G11TD545 2 9
1288 1365 1502 1100 1071 1135 1249 1728 1000 906 960 1440 1728 800 432…528 20G11TD617 2 9
1340 1420 1562 1250 1288 1365 1502 2048 1100 986 1045 1568 2048 900 432…528 20G11TD710 2 9
1453 1540 1694 1350 1340 1420 1562 2130 1250 1071 1135 1703 2130 1000 432…528 20G11TD740 2 9
1562 1655 1821 1500 1439 1525 1678 2288 1350 1199 1270 1905 2288 1100 432…528 20G11TD545 3 10
2114 2240 2464 2000 1953 2070 2277 3105 1750 1633 1730 2595 3105 1650 432…528 20G11TD740 3 10

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 9
PowerFlex 755 IP00, NEMA/UL Open Type Drive
600V AC, Three-Phase, 60 Hz Input
Three-Phase, 0…400 Hz Output
690V AC, Three-Phase, 50 Hz Input
Three-Phase, 0…400 Hz Output
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
HpCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V AC
335 355 391 NA 350 278 295 325 490 300 257 272 408 490 250 540…660 20G11TE295 1 8
373 395 435 400 335 355 391 533 350 278 295 443 533 300 540…660 20G11TE355 1 8
411 435 479 450 373 395 435 593 400 310 329 494 593 350 540…660 20G11TE395 1 8
434 460 506 500 411 435 479 639 450 335 355 533 639 350 540…660 20G11TE435 1 8
481 510 561 500 434 460 506 711 500 373 395 593 711 400 540…660 20G11TE460 1 8
514 545 600 550 481 510 561 765 500 401 425 638 765 450 540…660 20G11TE510 1 8
651 690 759 700 562 595 655 918 600 481 510 765 918 500 540…660 20G11TE295 2 9
717 760 836 800 595 630 693 1071 700 562 595 893 1071 600 540…660 20G11TE355 2 9
788 835 919 900 717 760 836 1140 800 595 630 945 1140 700 540…660 20G11TE395 2 9
849 900 990 950 779 825 908 1260 900 661 700 1050 1260 750 540…660 20G11TE435 2 9
925 980 1078 1000 849 900 990 1368 950 717 760 1140 1368 800 540…660 20G11TE460 2 9
986 1045 1150 1100 925 980 1078 1470 1000 769 815 1223 1470 900 540…660 20G11TE510 2 9
1151 1220 1342 1200 1048 1110 1221 1665 1100 868 920 1380 1665 1000 540…660 20G11TE395 3 10
1444 1530 1683 1500 1350 1430 1573 2145 1400 1123 1190 1785 2145 1250 540…660 20G11TE510 3 10
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kWCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V AC
311 330 363 NA 315 250 265 292 375 250 203 215 323 375 200 621…759 20G11TF265 1 8
349 370 407 355 311 330 363 473 315 250 265 398 473 250 621…759 20G11TF330 1 8
386 410 451 400 349 370 407 555 355 290 308 462 555 300 621…759 20G11TF370 1 8
433 460 506 450 391 415 457 639 400 349 370 555 639 355 621…759 20G11TF415 1 8
471 500 550 500 433 460 506 675 450 353 375 563 675 375 621…759 20G11TF460 1 8
499 530 583 530 471 500 550 750 500 389 413 620 750 400 621…759 20G11TF500 1 8
612 650 715 630 556 590 649 885 560 433 460 690 885 450 621…759 20G11TF265 2 9
669 710 781 710 612 650 715 975 630 471 500 750 975 500 621…759 20G11TF330 2 9
744 790 869 800 669 710 781 1065 710 556 590 885 1065 560 621…759 20G11TF370 2 9
810 860 946 850 721 765 842 1170 750 612 650 975 1170 630 621…759 20G11TF415 2 9
904 960 1056 900 749 795 875 1350 800 706 750 1125 1350 710 621…759 20G11TF460 2 9
961 1020 1122 1000 904 960 1056 1440 900 749 795 1193 1440 800 621…759 20G11TF500 2 9
1083 1150 1265 1100 980 1040 1144 1560 1000 815 865 1298 1560 900 621…759 20G11TF370 3 10
1399 1485 1634 1500 1319 1400 1540 2100 1400 1093 1160 1740 2100 1120 621…759 20G11TF500 3 10

10 Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
AC Input Drive Installation Kits
The following kits are available to assist you with installation of drive
components in your enclosure. Note that certain kits are required for proper
installation and for UL certification.
No. Kit
Frame 8 Equivalent Frame 9 Equivalent Frame 10 Equivalent
Description NotesCatalog Number Qty. Catalog Number Qty. Catalog Number Qty.
1 Converter (AC Input) Field
Termination
20-750-BUS2-F8 1 20-750-BUS2-F9 1 20-750-BUS2-F10 1 Provides power wiring connection. (4) (5)
2 Inverter (AC Output) Field
Termination
20-750-BUS3-F8 1 20-750-BUS3-F9 1 20-750-BUS3-F10 1
3 Inverter (DC Bus) Field
Termination - 400/480V 20-750-BUS4-F8(1)
1 20-750-BUS4-F9(3) 1 20-750-BUS4-F10(3) 1
Inverter (DC Bus) Field
Termination - 600/690V
1 20-750-BUS6-F9(3) 1 20-750-BUS6-F10(3) 1
4 Mounting, Back Panel 20-750-MNT2-F8 1 20-750-MNT2-F9 1 20-750-MNT2-F10 1 Drive mounting kit includes four brackets per
drive unit to mount the drive to the back of the
enclosure.
(5)
5 Mounting, Floor/Rail 20-750-MNT3-F8 1 20-750-MNT3-F9 1 20-750-MNT3-F10 1 Includes bottom rails and hardware to utilize
the roll-out feature of the drive.
(5)
6 Ducting, Outlet Top 20-750-DUCT2-F8 1 20-750-DUCT2-F8 2 20-750-DUCT2-F8 3 A duct adaptor is provided to direct exhaust air
from the top of the drive. Can be used for
horizontal or vertical installations.
(5)
7 Ducting, Bottom Inlet 20-750-DUCT4-F8 1 20-750-DUCT4-F8 2 20-750-DUCT4-F8 3 Provides a duct to direct air flow into the
bottom of the cabinet. Requires the Floor/Rail
kit to secure the duct.
8 Control Pod 20-750-POD1-F8 1 20-750-POD1-F8 1 20-750-POD1-F8 1 Control Pod including Main Control Board and
Fiber Interface Board. Mount in the left most
bay of the drive or remotely (see below).
(4) (6)
Control Pod Remote Harness 20-750-RPD1-F8 1 20-750-RPD1-F8(9) 2 20-750-RPD1-F8(9) 3 Hardware, fiber-optic, and power supply
cables to remotely mount the control pod up
to 23 m (75 ft) from the drive.
(5)
9 24V Harness 20-750-PH1-F8(2) 0 20-750-PH2-F9 1 20-750-PH3-F10 1 For control pod connection in the drive.
Important: Not required if the Remote
Mount kit is ordered.
(7)
10 Fiber-optic Cable, 0.6 m
(22 in.)
20-750-FCBL1-F8 1 (7) (8)
Fiber-optic Cable, 2.8 m
(110 in.)
20-750-FCBL1-F10 2 20-750-FCBL1-F10 3
11 Roll-out Cart 20-750-CART1-F8 1 20-750-CART1-F8 1 20-750-CART1-F8 1 A wheeled roll-out cart that facilitates drive
installation and removal.
(5)
12 EMC Core 20-750-EMCBUS1-F8 1 20-750-EMCBUS1-F8 2 20-750-EMCBUS1-F8 3 Common mode core kit for converter section
input on AC input drives. To be used with 20-
750-BUS2-F8. EN 61800-3 compliant
installations only.
20-750-EMCCM1-F8 1 20-750-EMCCM1-F8 2 20-750-EMCCM1-F8 3 Common mode core kit for inverter section
output. For AC Input or Common DC Input
drives. EN 61800-3 compliant installations
only.
(1) Optional for Frame 8 equivalent applications; only use if application requires connection to the DC bus (such as a brake or chopper).
(2) Frame 8 equivalent 24V DC harness ships with each drive unit.
(3) Fuses are included.
(4) This kit is required for UL installations.
(5) This is a recommended kit.
(6) This kit is required.
(7) Required when mounting control pod in the drive.
(8) 20-750-PH1-F8 and 20-750-FCBL1-F8 are used for a drive mounted control pod. If the control pod is to be remote mounted up to 23m (75ft), order 20-750-RPD1-F8 kit instead.
(9) For frame 9 and 10 installations, remove the two-position connector from the harnesses and combine the leads into one connector that plugs into P14 on the Fiber Interface Board (see page 43).

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 11
PowerFlex 755 IP00, NEMA/UL Open Type Drive
PE
PE
PE
PE
?
Power
755
Frame 8
Frame 9
Frame 10
1
2
4
6
3
5
4
1
2
4
6
3
5
4
1
2
4
6
3
5
4
7
8
11
9
12
10

12 Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Common DC Input Drives Drive Ratings
The following tables provide rating and selection information for the common
DC input PowerFlex 755 IP00 NEMA/UL Open Type drives.
540V DC, 50 Hz Input
Three-Phase, 0…400 Hz Output
650V DC, 60 Hz Input
Three-Phase, 0…400 Hz Output
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kWCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V DC
621 540 594 NA 315 529 460 506 693 250 443 385 578 693 200 486…594 20G14TC460 1 8
673 585 644 315 621 540 594 821 315 525 456 684 821 250 486…594 20G14TC540 1 8
704 612 673 355 652 567 624 851 315 543 472 708 851 250 486…594 20G14TC567 1 8
863 750 825 400 748 650 715 975 355 621 540 810 975 315 486…594 20G14TC650 1 8
916 796 876 450 863 750 825 1125 400 673 585 878 1125 315 486…594 20G14TC750 1 8
957 832 915 450 886 770 847 1155 400 739 642 963 1155 355 486…594 20G14TC770 1 8
1197 1040 1144 560 1047 910 1001 1365 500 863 750 1125 1365 400 486…594 20G14TC460 2 9
1254 1090 1199 630 1197 1040 1144 1584 560 1013 880 1320 1584 500 486…594 20G14TC540 2 9
1352 1175 1293 710 1254 1090 1199 1638 630 1047 910 1365 1638 500 486…594 20G14TC567 2 9
1686 1465 1612 800 1352 1175 1293 1872 710 1197 1040 1560 1872 560 486…594 20G14TC650 2 9
1703 1480 1628 850 1686 1465 1612 2198 800 1254 1090 1635 2198 630 486…594 20G14TC750 2 9
1841 1600 1760 900 1703 1480 1628 2220 850 1352 1175 1763 2220 710 486…594 20G14TC770 2 9
1974 1715 1887 1000 1830 1590 1749 2385 900 1525 1325 1988 2385 710 486…594 20G14TC567 3 10
2681 2330 2563 1400 2474 2150 2365 3225 1250 2071 1800 2700 3225 1000 486…594 20G14TC770 3 10
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
HpCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V DC
533 485 534 NA 400 473 430 473 666 350 407 370 555 666 300 585…715 20G14TD430 1 8
599 545 600 450 533 485 534 745 400 455 414 621 745 350 585…715 20G14TD485 1 8
649 590 649 500 599 545 600 818 450 499 454 681 818 350 585…715 20G14TD545 1 8
781 710 781 600 678 617 679 926 500 533 485 728 926 400 585…715 20G14TD617 1 8
841 765 842 650 781 710 781 1065 600 599 545 818 1065 450 585…715 20G14TD710 1 8
880 800 880 700 814 740 817 1110 650 678 617 926 1110 500 585…715 20G14TD740 1 8
1055 960 1056 800 880 800 880 1278 700 781 710 1065 1278 600 585…715 20G14TD430 2 9
1149 1045 1150 900 1055 960 1056 1440 800 874 795 1193 1440 700 585…715 20G14TD485 2 9
1248 1135 1249 1000 1149 1045 1150 1568 900 880 800 1200 1568 750 585…715 20G14TD545 2 9
1501 1365 1502 1100 1248 1135 1249 1728 1000 1055 960 1440 1728 800 585…715 20G14TD617 2 9
1561 1420 1562 1250 1501 1365 1502 2048 1100 1149 1045 1568 2048 900 585…715 20G14TD710 2 9
1693 1540 1694 1350 1561 1420 1562 2130 1250 1248 1135 1703 2130 1000 585…715 20G14TD740 2 9
1819 1655 1821 1500 1677 1525 1678 2288 1350 1396 1270 1905 2288 1100 585…715 20G14TD545 3 10
2463 2240 2464 2000 2276 2070 2277 3105 1750 1902 1730 2595 3105 1650 585…715 20G14TD740 3 10

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 13
PowerFlex 755 IP00, NEMA/UL Open Type Drive
810V DC, 60 Hz Input
Three-Phase, 0…400 Hz Output
932V DC, 50 Hz Input
Three-Phase, 0…400 Hz Output
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
Hp
Input
Amps
Output Amps
HpCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V DC
391 355 391 NA 350 325 295 325 490 300 300 272 408 490 250 729…891 20G14TE295 1 8
436 395 435 400 391 355 391 533 350 325 295 443 533 300 729…891 20G14TE355 1 8
480 435 479 450 436 395 435 593 400 363 329 494 593 350 729…891 20G14TE395 1 8
507 460 506 500 480 435 479 639 450 391 355 533 639 350 729…891 20G14TE435 1 8
562 510 561 500 507 460 506 711 500 436 395 593 711 400 729…891 20G14TE460 1 8
601 545 600 550 562 510 561 765 500 469 425 638 765 450 729…891 20G14TE510 1 8
761 690 759 700 656 595 655 918 600 562 510 765 918 500 729…891 20G14TE295 2 9
838 760 836 800 695 630 693 1071 700 656 595 893 1071 600 729…891 20G14TE355 2 9
921 835 919 900 838 760 836 1140 800 695 630 945 1140 700 729…891 20G14TE395 2 9
993 900 990 950 910 825 908 1260 900 772 700 1050 1260 750 729…891 20G14TE435 2 9
1081 980 1078 1000 993 900 990 1368 950 838 760 1140 1368 800 729…891 20G14TE460 2 9
1152 1045 1150 1100 1081 980 1078 1470 1000 899 815 1223 1470 900 729…891 20G14TE510 2 9
1345 1220 1342 1200 1224 1110 1221 1665 1100 1015 920 1380 1665 1000 729…891 20G14TE395 3 10
1687 1530 1683 1500 1577 1430 1573 2145 1400 1312 1190 1785 2145 1250 729…891 20G14TE510 3 10
Light Duty Normal Duty Heavy Duty InputVoltage
Range Base Drive
Catalog Number
Quantity
Required
Equivalent
Frame Size
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kW
Input
Amps
Output Amps
kWCont. 1 min 3 s Cont. 1 min 3 s Cont. 1 min 3 s V DC
363 330 363 NA 315 292 265 292 375 250 237 215 323 375 200 839…1025 20G14TF265 1 8
407 370 407 355 363 330 363 473 315 292 265 398 473 250 839…1025 20G14TF330 1 8
451 410 451 400 407 370 407 555 355 339 308 462 555 300 839…1025 20G14TF370 1 8
506 460 506 450 457 415 457 639 400 407 370 555 639 355 839…1025 20G14TF415 1 8
550 500 550 500 506 460 506 675 450 413 375 563 675 375 839…1025 20G14TF460 1 8
583 530 583 530 550 500 550 750 500 454 413 620 750 400 839…1025 20G14TF500 1 8
715 650 715 630 649 590 649 885 560 506 460 690 885 450 839…1025 20G14TF265 2 9
781 710 781 710 715 650 715 975 630 550 500 750 975 500 839…1025 20G14TF330 2 9
869 790 869 800 781 710 781 1065 710 649 590 885 1065 560 839…1025 20G14TF370 2 9
946 860 946 850 842 765 842 1170 750 715 650 975 1170 630 839…1025 20G14TF415 2 9
1056 960 1056 900 875 795 875 1350 800 825 750 1125 1350 710 839…1025 20G14TF460 2 9
1122 1020 1122 1000 1056 960 1056 1440 900 875 795 1193 1440 800 839…1025 20G14TF500 2 9
1265 1150 1265 1100 1144 1040 1144 1560 1000 952 865 1298 1560 900 839…1025 20G14TF370 3 10
1634 1485 1634 1500 1540 1400 1540 2100 1400 1276 1160 1740 2100 1120 839…1025 20G14TF500 3 10

14 Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Common DC Input Drive Installation Kits
The following kits are available to assist you with installation of drive
components in your enclosure. Note that certain kits are required for proper
installation and for UL certification.
No. Kit
Frame 8 Equivalent Frame 9 Equivalent Frame 10 Equivalent
Description NotesCatalog Number Qty. Catalog Number Qty. Catalog Number Qty.
1 DC Input for Common
Bus Precharge
20-750-BUS5-F8 1 20-750-BUS5-F9 1 20-750-BUS5-F10 1 Provides power wiring connection. 20-750-
BUS5 kits include EMC input cores.
(2) (3)
2 Inverter (AC Output)
Field Termination
20-750-BUS3-F8 1 20-750-BUS3-F9 1 20-750-BUS3-F10 1
3 Mounting, Back Panel 20-750-MNT2-F8 1 20-750-MNT2-F9 1 20-750-MNT2-F10 1 Drive mounting kit includes four brackets per
drive unit to mount the drive to the back of the
enclosure.
(3)
4 Mounting, Floor/Rail 20-750-MNT3-F8 1 20-750-MNT3-F9 1 20-750-MNT3-F10 1 Includes bottom rails and hardware to utilize
the roll-out feature of the drive.
(3)
5 Ducting, Outlet Top 20-750-DUCT2-F8 1 20-750-DUCT2-F8 2 20-750-DUCT2-F8 3 A duct adaptor is provided to direct exhaust air
from the top of the drive. Can be used for
horizontal or vertical installations.
(3)
6 Ducting, Bottom Inlet 20-750-DUCT4-F8 1 20-750-DUCT4-F8 2 20-750-DUCT4-F8 3 Provides a duct to direct air flow into the
bottom of the cabinet. Requires the Floor/Rail
kit to secure the duct.
7 Control Pod 20-750-POD1-F8 1 20-750-POD1-F8 1 20-750-POD1-F8 1 Control Pod including Main Control Board and
Fiber Interface Board. Mount in the left most
bay of the drive or remotely (see below).
(2) (4)
Control POD Remote
Harness
20-750-RPD1-F8 1 20-750-RPD1-F8(7) 2 20-750-RPD1-F8(7) 3 Hardware, fiber-optic, and power supply
cables to remotely mount the control pod up
to 23 m (75 ft) from the drive.
(3)
8 24V Harness 20-750-PH1-F8 (1) 0 20-750-PH2-F9 1 20-750-PH3-F10 1 For Control Pod connection in the drive.
Important: Not required if the Remote
Mount kit is ordered.
(5)
9 Fiber-optic Cable, 0.6 m
(22 in.)
20-750-FCBL1-F8 1 (5) (6)
10 Fiber-optic Cable, 2.8 m
(110 in.)
20-750-FCBL1-F10 2 20-750-FCBL1-F10 3
Roll-out Cart 20-750-CART1-F8 1 20-750-CART1-F8 1 20-750-CART1-F8 1 A wheeled roll-out cart that facilitates drive
installation and removal.
(3)
11 EMC Core 20-750-EMCCM1-F8 1 20-750-EMCCM1-F8 2 20-750-EMCCM1-F8 3 Common mode core kit for inverter section
output. For AC Input or Common DC Input
drives. EN 61800-3 compliant installations
only.
12 Circuit Breaker 1489-A2D130 1 1489-A2D130 2 1489-A2D130 3 Control Transformer Overload Protection -
Required for Common DC Input drives, see
page 20.
(2)
Circuit Breaker Lock 1489-AALOA 1 1489-AALOA 2 1489-AALOA 3
(1) Frame 8 equivalent 24V DC harness ships with each drive unit.
(2) This kit is required for UL installations.
(3) This kit is recommended.
(4) This kit is required.
(5) Required when mounting control pod in the drive.
(6) 20-750-PH1-F8 and 20-750-FBCL1-F8 are used for a drive mounted control pod. If the control pod is to be remote mounted up to 23m(75ft), order 20-750-RPD1-F8 kit instead.
(7) For frame 9 and 10 installations, remove the two-position connector from the harnesses and combine the leads into one connector that plugs into P14 on the Fiber Interface Board (see page 43).

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 15
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Power
755
Frame 8
Frame 9
Frame 10
Not Shown
1
3
4
3
5
2
1
4
3
5
2
3
1
4
3
5
2
3
6
7
8
9
10
11
12

16 Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Installation Tools
This list covers the tools needed for drive installation.
Enclosure Requirements The following specifications must be met for proper installation.
Bus Bars
Power wiring is connected to the drive power terminals (see page 47) using the
Field Termination kits shown on page 6 and page 7 or fabricated using material
with the following specifications:
•Material: CDA 110 Copper
•Minimum Cross Section: 80.7mm2(0.125 in.2) per each 100 A of drive
rating.
IMPORTANT
Care must be taken to ensure that tools and/or hardware components do not fall into
open drive assemblies. Do not energize the drive unless all loose tools and/or hardware
components have been removed from the drive assemblies and enclosure.
Tool Description Details
ESD-protected place of work Working surface, Floor covering, seat and ground connections
ESD-protective clothing Wrist wrap, shoes, overall clothing (coat)
Allen socket wrench 5 mm
Allen socket wrench extension 254 mm (10 in.)
Flat nose screw driver 5 mm (0.19 in.), 6.4 mm (0.25 in.), 9.5 mm (0.375 in.), #1, #2
Hexalobular screw driver/bit #15, #20, #25, #40, #45
Hexagonal socket wrench 7 mm, 8 mm, 10 mm, 12 mm, 13 mm, 17 mm, 18 mm
Combination wrench 10 mm, 17 mm
Phillips screw driver/bit #2, 492-C
Pozidriv #2
Torque wrench 1...12 N•m (8.8…106 lb•in)
Torque wrench 6...50 N•m (53…443 lb•in)
Roll-out cart 20-750-CART1-F8
Note: The roll-out cart is required to remove the drive assembly from the
enclosure.
Frame8Frame9Frame10
Width 800 mm (31.5 in.) min. 1600 mm (63.0 in.) min. 2400 mm (94.5 in.) min.
Depth 600 mm (23.6 in.) min.
Height 2200 mm (86.6 in.) min.
Weight Enclosure must be able to support the total equipment weight stated on page 36.
Construction According to EN60439-1
ATTENTION: To guard against drive damage, DO NOT connect power wires
directly to the drive power terminals. Power wiring must be connected to bus
bars which are fastened to the drive power terminals.

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 17
PowerFlex 755 IP00, NEMA/UL Open Type Drive
In addition, the bus bar must be supported as detailed in the figure below.
Environmental Requirements
The drive shall be mounted in an enclosure with 40 °C (104 °F) ambient external
to the enclosure and surrounding airflow as described on pages 17…20.
See the PowerFlex 750-Series AC Drives Technical Data, publication
750-TD001, for detailed specifications and ratings.
Cooling Airflow and Ventilation - IP20, NEMA Type 1 Enclosures
The PowerFlex 755 drive is designed for a dual airflow system consisting of drive
power cooling and enclosure cooling. The drive blower generates a high velocity
airflow for the drive power cooling through a duct network that also serves as the
frame of an open type drive. The enclosure cooling requirements must be
supplied as specified.
When mounting the drive vertically, the enclosure door must be provided with
openings for air intake as shown. To achieve sufficient cooling inside the
enclosure, the dimensions for total area and location of incoming airflow
provided in Figure 1 should be followed. Horizontal mounting details for single
drive units can be found on page 26.
The cooling arrangements inside the enclosure must be such that they
prevent hot output air from mixing with the incoming fresh air.
Heat Dissipation
ATTENTION: To guard against equipment damage caused by excessive heat,
proper airflow must be maintained at all times. See the guidelines on the
following pages.
Frame Enclosure Cooling Drive Power Cooling Total (if drive is fully enclosed)
8 2000 Watts 8200 Watts 10,200 Watts
9 4000 Watts 16,400 Watts 20,400 Watts
10 6000 Watts 24,600 Watts 30,600 Watts
Drive
Power Terminal
Support within 305 mm (12.0 in.)
Bus Bar
T45 - M10 x 35 mm SEMS
22.4 N•m (200 lb•in)

18 Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Figure 1 - Dual Airflow System
Figure 2 - Intake Duct Details
Ventilation Requirements
No. Free Area Description
1780cm
2(120.9 in.2)Enclosure
Cooling
2EnclosureFans
(1)
(1) Enclosure fans are required and must meet or exceed the
performance shown in Figure 5. In addition, the fans should be
mounted as high as possible on the door and aligned with the
front of the drive assembly.
3 See Important statement below Drive Power
Cooling
4811.6cm
2(125.8 in.2)
Enclosure Cooling
Drive Power Cooling
Shown with optional hood and inlet filter.
1
2
3
4
IMPORTANT
For vertical mounting applications a duct section must be fabricated to fit
between the gasket on the drive and the inside of the enclosure door.
Depending on the enclosure used, the drive mounting location in the enclosure
(set-back) can range between 12.7…54.5 mm (0.50…2.13 in.). To assure
sufficient Control Pod access, the maximum set-back of the drive behind the
door is 54.5 mm (2.13 in.). The duct must contact and slightly compress the
gasket to seal the drive power cooling air from the enclosure cooling air.
Reference the dimensions provided in Figure 2.
410.5
(16.16)
451.0
(17.75)
114.3
(4.50)
87.2
(3.43)
46.7
(1.84)
45°
Duct must contact gasket
when door is closed.
Gasket
Duct
(User Supplied)
Upper Vent
Filter not shown for clarity.
Measurements are in mm and (in).

Rockwell Automation Publication 750-IN020D-EN-P - May 2017 19
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Figure 3 - Outlet Ducting Kit (20-750-DUCT2-F8) Details
Figure 4 - Outlet Ducting Kit (20-750-DUCT2-F8) Dimensions
PE
PE
Outlet Ducting kit attaches to top
mounting bracket and should be
installed before the drive unit is
rolled-in.
User supplied ducting is mounted
to enclosure top and matches up
with the ducting kit. Use M6 screws
of suitable length to attach duct to
adapter.
T40 - M8
11.3 N•m (100 lb•in)
0.00 (0.000)
13.00 (0.512) 77.90 (3.067)
168.80 (6.646)
259.70 (10.224) 350.60 (13.803) 428.50 (16.870) 441.50 (17.382)
0.00 (0.000)
13.00 (0.512)
84.00 (3.307)
168.00 (6.614)
181.00 (7.126)
M6 Hole - 14 places
Torque 5.1 N•m (45 lb•in)

20 Rockwell Automation Publication 750-IN020D-EN-P - May 2017
PowerFlex 755 IP00, NEMA/UL Open Type Drive
Enclosure Fans
Enclosure fans are required and must meet or exceed the performance shown in
Figure 5 for two fans operating at 10.76 CMM (380 CFM) each with 1.27 mm
(0.05 in.) H2O static pressure.
Figure 5 - Fan Performance (per bay)
The enclosure fans can be powered from the Control Transformer which is
located in the upper part of the drive assembly. The transformer supplies 230V
AC (±10%) power to the drive and drive blower with sufficient power available
(240 VA/bay) for the enclosure fans. The terminating point for the enclosure fans
is at terminal block TB2 on the right side of the drive assembly (see Figure 6).
•Recommended wire is 1.3 mm2(16 AWG) tinned copper stranded
conductor, PVC insulated, 600V, 105 °C (221 °F).
•Recommended Connector; Phoenix P/N 1757019, 5.08 mm (.2 in.)
pitch, 2 position, 12A, 250V, 24…12 AWG.
To gain access to the Control Transformer, see the PowerFlex 755 AC Drives
Hardware Service Manual, publication 750-TG001. To select or verify
transformer primary voltage, see page 41.
For Common DC Input drives, the user must provide:
1. Electrical power to the drive for the enclosure fans, and
2. overload protection for the drive control transformer. The overload device
must be suitable for 120/240V AC, 50/60 Hz, 8.3/4.2 A, 1 kVA.
Allen-Bradley circuit breaker catalog number 1489-A2D130 is acceptable.
A circuit breaker lock (1489-AALOA) is also available.
For additional information, see the PowerFlex 750-Series AC Drives Installation
Instructions, publication 750-IN001. See the section “120V/240V AC Power
Supply Connections - Common DC Input Drives.”
0.00
25.0
20.0
15.0
10.0
5.0
0.00
0.98
0.78
0.59
0.39
0.20
0.00
2.55 5.09 7.64 10.19 12.75
0.00 90.0 180.0 270.0 360.0 450.0
Flowrate (CMM)
Flowrate (CFM)
Static Pressure (mmAq)
Static Pressure (InAq)
50 Hz 60 Hz
Typical enclosure pressure with
ventilation requirements described in
Figure 1