Allen-Bradley 140G-R Series User manual

WARNING:
WARNUNG:
AVERTISSEMENT:
To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
140G-R
LSIG
LSIG microprocessor-based electronic release for 140G-R
Sganciatore elettronico a microprocessore LSIG
Elektronischer Mikroprozessor-Auslöser LSIG
Déclencheur électronique à microprocesseur LSIG
Relé electrónico con microprocesador LSIG
Bul. 140G
DIR 1000650R0502 Version 00
140G-R
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）物
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。（NFPA70Eの要件に従ってください）
Retaining
plug tool
Screw
Label
Locking
cover
LENGT H dia.
20 mm (0.79" ) 4
OPTIONAL
x2
OPTIONAL
See DIR 1000529R0510
21
Screw
LENGTH dia.
10 mm (0.39" ) 3
Screw
LENGTH dia.
8 mm (0.31") 3
LENGTH dia.
6 mm (0.24" ) 3
If not part of
replacement kit, a
catalog number
have to be listed

(2)
1 2
34
DIR 1000650R0502 Version 00
LENGTH dia.
6 mm (0.24" ) 3
LENGTH dia.
10 mm (0.39" ) 3
5
torque?

6
(3)
DIR 1000650R0502 Version 00
121
2
LENGTH dia.
8 mm (0.31") 3
1
2
7
9
8
10 11
torque?
torque?

(4)
DIR 1000650R0502 Version 00
13
12
T5 T6 T7 T8 T9
T10 W4
W3
K1
K2 K11
K21
K15
K14
K13
K12 95P
98P
W2
W1
T5 T6 T7 T8 T9 T10 W3 W4 K1 K2 K21 K11 K12 K13 K14 K15 95P 98P W1 W2

(5)
DIR 1000650R0502 Version 00
14

DIR 1000650R0502 Version 00 (L8482) - Preliminary
Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN133A-EN-P - April 2015
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page
15
In ≤ Iu
9.7 lb in
1.1 Nm
LENGT H dia.
20 mm (0.79" ) 4