Alliance Laundry Systems H011C User manual

Installation
Tumble Action
Washers
H011C
NOTA: El manual en
español aparece después
del manual en inglés.
Part No. 685980R3
March 2000
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

© Copyright 2000, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
685980 1
Table of
Contents
Replacement Parts .............................................................................. 2
Roughing In Dimensions .................................................................... 3
Before You Start ................................................................................. 5
Tools ..................................................................................................... 5
Electrical............................................................................................... 5
Water..................................................................................................... 5
Accessories Bag.................................................................................... 5
Installing the Washer ......................................................................... 7
Step 1: Position Washer Near Installation Area ................................... 7
Step 2: Connect Water Inlet Hoses....................................................... 7
Step 3: Connect Drain Hose to Drain Receptacle................................. 8
Standpipe Installation....................................................................... 8
Sink Installation ............................................................................... 9
In-the-Wall Installation.................................................................... 9
Laundry Tub Installation.................................................................. 9
Step 4: Position and Level the Washer................................................. 10
Step 5: Remove the Shock Sleeves and Shipping Brace...................... 11
Step 6: Wipe Out Inside of Wash Drum............................................... 11
Step 7: Plug In the Washer ................................................................... 11
Step 8: Check Installation..................................................................... 11
Moving Washer to a New Location................................................... 13
Electrical Requirements..................................................................... 15
Water Supply Requirements ............................................................. 17
Water Temperature ............................................................................... 17
Water Pressure...................................................................................... 17
Risers .................................................................................................... 17
Installer Check....................................................................... Back Cover

2685980
Replacement Parts
If replacement parts are required, contact the source
from where you purchased your washer, or contact:
Alliance Laundry Systems
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
Phone [phone]
for the name and address of the nearest authorized
parts distributor.

3
685980
Roughing In Dimensions
H327I
H327I
28"
(71.1 cm) 2" (5.1 cm)
17.5"
(44.8 cm)
36.6" (93 cm)
14.9"
(37.9 cm)
43" (109.2 cm)
31.1" (79 cm)
29.6" (75.1 cm)
26.9"
(68.3 cm)

685980
4
Notes

5
685980
Before You Start
Tools
For most installations, the basic tools you will need
are:
Electrical
Refer to Serial Plate for specific electrical
requirements. For more detailed information refer to
section on Electrical Requirements.
Water
Washer needs two standard 3/4 inch (19.1 mm) water
supply faucets with a pressure between 20 and 120
pounds per square inch (138 to 827 kPa). For more
detailed information refer to section on Water Supply
Requirements.
Accessories Bag
An accessories bag has been shipped inside your
washer. It includes:
●Two inlet hoses with washers. Refer to Step 2 of
Installing the Washer.
●Four rubber feet. Refer to Step 4 of Installing the
Washer.
●Beaded tie-down strap. Refer to Step 3 of
Installing the Washer.
●Installation instructions.
●Use and Care Guide.
●Operating insert.
●Warranty bond.
●Helpful Hints insert.
●Bag for storing shipping materials.
D798I
D798i
9
/
1
6
"
Wrench Pliers
Level
Screwdriver Socket Wrench

685980
6
Notes

7
685980
Installing the Washer
Step 1: Position Washer Near
Installation Area
IMPORTANT: Install dryer before washer. This
allows room for attaching exhaust duct.
Move washer as close to the desired area of
installation as possible.
Step 2: Connect Water Inlet
Hoses
NOTE: Refer to section on Water Supply
Requirements before connecting water inlet hoses.
Remove the four plain rubber washers from
accessories bag, and install them according to the
illustration.
Turn on the water supply faucets and flush the lines for
approximately two minutes to remove any foreign
materials that could clog the screens in the water
mixing valve.
NOTE: When installing in newly constructed or
renovated building, it is very important to flush the
lines since build-up may have occurred during
construction.
IMPORTANT: Thread hose couplings onto valve
connections finger-tight, then approximately 1/4
turn with pliers. DO NOT cross thread or
overtighten couplings.
Turn water on and check for leaks. If leaks are found,
retighten the hose couplings. Continue tightening and
rechecking until no leaks are found.
D772I
D772I
W528I
1Rubber Washer (Plain)
2Install This End of Hose to Water Supply
Faucet
3Install This End of Hose to Valve
Connections at Rear of Washer
4Inlet Hose
H328I
1Water Supply Faucets
2Cold Water Connection
3Hot Water Connection
4Water Inlet Hoses
1
2
3
4
H328I
123
Water
Mixing
Valve
4

Installing the Washer
685980
8
Step 3: Connect Drain Hose to
Drain Receptacle
Remove the drain hose from its shipping position on
the rear of the washer by unhooking the hose from the
retainer clamp.
Find the instructions, on the following pages, that are
appropriate for your type of drain receptacle
(standpipe, sink, wall, or laundry tub). Follow these
instructions to properly install the drain hose.
IMPORTANT: Drain receptacle must be capable of
handling a minimum of 1-1/4 inch (32 cm) outside
diameter drain hose.
Standpipe Installation
Place the drain hose into the standpipe.
Remove the beaded tie-down strap from accessories
bag and place around standpipe and drain hose and
tighten strap to hold hose to standpipe. This will
prevent the drain hose from dislodging from drain
receptacle during use.
H329I
1Retainer Clamp
H329I
1
H330I
124" to 36" (91.44 cm Recommended Height)
2Standpipe 2" (5.08 cm) or 1-1/2" (4 cm)
3Beaded Tie-Down Strap
1
23