Alliance Laundry Systems H236I Owner's manual

Installation and Operation
H236I
3
21
OPERATING INSTRUCTIO
Select Wash Temperature
Select Fabric Type
Load Supply Dispenser (See
Insert Coin(s) / Card.
1.
2.
3.
5.
Open Dispenser
Compartment (as
Close Dispenser
1.
2
3
Detergent
Detergent
1.
2.
DISPENSER INSTRUCTION
685942
685557
NOTA: El manual en español aparece después del manual en inglés.
Front Load
Washers
Metered Commercial
Part No. 685945R5
October 1999

685945 1
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If the washer changes ownership,
be sure this manual accompanies the washer.)
© Copyright 1999, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means
without the expressed written consent of the publisher.
For your safety and to reduce the risk of
fire or an explosion, do not store or use
gasoline or other flammable vapors and
liquids in the vicinity of this or any other
appliance.
WARNING

2685945
Replacement Parts . . .
If replacement parts are required, contact the source from
where you purchased your washer, or contact: Alliance Laundry Systems LLC
Shepard Street
P.O. Box 990
Ripon, WI 54971-0990
Phone: [phone]
for the name and address of the nearest authorized parts
distributor.
Table of
Contents
Replacement Parts ...............................................................................2
Important Safety Instructions .............................................................3
Dimensions and Specifications.............................................................5
Additional Security...............................................................................5
Coin Slide Guards.................................................................................5
Washer Slide Extension .......................................................................6
Before You Start....................................................................................7
Installing the Washer
Step 1: Position Washer Near Installation Area..................................7
Step 2: Connect Water Inlet Hoses.....................................................8
Step 3: Connect Drain Hose to Drain Receptacle...............................9
Step 4: Remove the Shock Sleeves and Shipping Brace ..................10
Step 5: Position and Level the Washer .............................................10
Step 6: Wipe Out Inside of Wash Drum...........................................11
Step 7: Plug in the Washer................................................................11
Step 8: Check Installation.................................................................11
Moving Washer to a New Location ..................................................12
Electrical Requirements ....................................................................13
Water Supply Requirements..............................................................14
Operation Instructions for Electromechanical Washers
Step 1: Load Laundry........................................................................15
Step 2: Close Loading Door..............................................................15
Step 3: Add Laundry Supplies..........................................................15
Step 4: Set WASH/RINSE Temperatures.........................................16
Step 5: Select Fabric Selector ...........................................................16
Step 6: Insert Money.........................................................................16
Indicator Lights.................................................................................16
Operation Instructions for Electronic Control Washers
Step 1: Load Laundry........................................................................17
Step 2: Close Loading Door..............................................................17
Step 3: Add Laundry Supplies..........................................................17
Step 4: Set Fabric Selector................................................................18
Step 5: Set Wash Temperature..........................................................18
Step 6: Insert Coin(s) or Card...........................................................18
Step 7: Start Washer..........................................................................18
Indicator Lights.................................................................................19
Maintenance
Cold Weather Care ...........................................................................20
Care of Your Washer .......................................................................20
Vacations and Extended Non-Use ....................................................20
Before You Call For Service ..............................................................21
Information for Handy Reference ....................................................22
Installer Checklist ...............................................................Back Cover

685945 3
IMPORTANT SAFETY INSTRUCTIONS
(SAVE THESE INSTRUCTIONS)
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS
in the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted
with gasoline, dry-cleaning solvents, or other
flammable or explosive substances as they give
off vapors that could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors
that could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not
been used for two weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If the hot water system
has not been used for such a period, before
using a washing machine or combination
washer-dryer, turn on all hot water faucets and
let the water flow from each for several
minutes. This will release any accumulated
hydrogen gas. The gas is flammable, do not
smoke or use an open flame during this time.
6. Do not allow children to play on or in the
washer. Close supervision of children is
necessary when the washer is used near
children. This is a safety rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum
is moving.
9. Do not install or store the washer where it will
be exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer,
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that you understand and have the
skills to carry out.
12. To reduce the risk of an electric shock or fire,
DO NOT use an extension cord or an adapter
to connect the washer to the electrical power
source.
13. Use your washer only for its intended purpose,
washing clothes.
14. ALWAYS disconnect the washer from
electrical supply before attempting any service.
Disconnect the power cord by grasping the
plug, not the cord.
15. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power
and grounding must comply with local codes
and be made by licensed personnel when
required. Do not do it yourself unless you know
how!
16. To reduce the risk of fire, clothes which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc. or anything
containing wax or chemicals such as in mops
and cleaning cloths, must not be put into the
washer.Theseflammablesubstancesmay cause
the fabric to catch on fire by itself.
17. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
18. Keep your washer in good condition. Bumping
or dropping the washer can damage safety
features. If this occurs, have your washer
checked by a qualified service person.
19. If the supply cord is damaged, it must be
replaced by a special cord or assembly
available from the manufacturer or its service
agent.
20. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions: W023E
WARNING
(continued)

4685945
21. Loading door MUST BE CLOSED any time
the washer is to fill, tumble or spin. DO NOT
by-pass the loading door switch by permitting
the washer to operate with the loading door
open.
22. Always read and follow manufacturer’s
instructions on packages of laundry and
cleaning aids. Heed all warnings or
precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of
children at all times (preferably in a locked
cabinet).
23. Always follow the fabric care instructions
supplied by the garment manufacturer.
24. Never operate the washer with any guards
and/or panels removed.
25. DO NOT operate the washer with missing or
broken parts.
26. DO NOT by-pass any safety devices.
27. Failure to install, maintain, and/or operate this
washer according to the manufacturer's
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE:TheWARNINGandIMPORTANTSAFETY
INSTRUCTIONS appearing in this manual are not
meant to cover all possible conditions and situations
that may occur. Common sense, caution and care
must be exercised when installing, maintaining, or
operating the washer.
Always contact your dealer, distributor, service agent or
the manufacturer about any problems or conditions you
do not understand.

685945 5
Dimensions and Specifications . . .
Additional Security . . .
Torx security screws are available (as optional equipment
at extra cost) for securing lower access panel to washer.
Order part number 62853.
A Torx bit, part number 282P4, is available (as optional
equipment at extra cost) for installing the Torx security
screws.
A Torx bit holder, part number 24161, is available (as
optional equipment at extra cost) to be used with the Torx
bit.
Coin Slide Guards . . .
(Coin Slide Models Only)
Using serrated hex head screws from accessories bag,
install coin slide guard to front of control cabinet. See
illustration.
A special security screw kit is available (as optional
equipment at extra cost) for securing the coin slide guard
and front panel to front of washer. Order Security Kit
No. 298P3. A special driver, part number 56217, is
available (as optional equipment at extra cost) for
installing the special security screws.
NOTE: Coin slides and coin drawers are shown for
illustration only. You must obtain them locally.
26.9" (68.3 cm)
28" (71.1 cm)
43" (109.2 cm)
29.6" (75.1 cm)
2"
(5.1 cm)
31.1" (79 cm)
14.3"
(36.3 cm)
17.5"
(44.8 cm)
H270IE3a
3
21
OPERATING INSTRUCTIONS
Select Wash Temperature
HOT, WARM, COLD.
Select Fabric Type
NORMAL, PERM PRESS, DELICATE.
Load Supply Dispenser (See Instructions Below).
Load Clothes.
Insert Coin(s) / Card.
To Start Washer-Close Door and Push Start.
1.
2.
3.
4.
5.
6.
Open Dispenser Door.
Load Supplies in Proper
Compartment (as Indicated).
Close Dispenser Door.
1.
2.
3.
Detergent
Liquid Bleach
Fabric Softener
1.
2.
3.
DISPENSER INSTRUCTIONS
PERMANENT PRESS ALL FABRIC
685942
H174I
685557

6685945
Washer Slide Extension . . .
(Coin Slide Models Only)
Remove slide extension, shoulder screw, plastic boot,
actuator, actuator support, screws and lockwashers from
the accessories bag. Install slide extension as follows:
1. Unlock and open service door. Remove locking rod
holding coin slide to front of security cabinet.
NOTE: Refer to following illustration for Steps 2
through 4.
2. Assemble plastic boot (No. 36165) onto actuator
support (No. 685592).
3. Assemble actuator (No. 36164) to actuator support
(No. 685592) using shoulder screw (No. 36166).
4. Place actuator and support assembly onto slide
extension, and install screw and lockwasher (No.
03950).
5. Install assembed slide extension through coin slide
opening of security cabinet by reaching through
service door opening.
6. Assemble slide extension (No. 685593) to top side
of coin slide using two screws and lockwashers
(No. 03950), and tighten firmly. See illustration
below.
7. Reinstall assembled coin slide in security cabinet.
Close and lock service door.
After slide extension has been installed, check washer
operation as follows:
1. Connect electrical power to washer.
NOTE: To determine if slide functions properly,
allow washer to complete its cycle, and for timer to
stop, before starting evaluation process.
2. Place required number of coins in slide. Push slide in
slowly and listen for coins to drop into coin drawer.
3. Push slide in a little farther and observe through
service door opening that actuator drops beyond
timer clutch. Continue pushing slide all the way in
and pull back. Confirm that the actuator will rotate
timer clutch and wash cycle starts.
NOTE: Washer will not start until Push-to-Start has
been pressed.
To reduce the risk of electric shock, fire,
explosion, serious injury or death:
• Disconnect electric power to the washer
before servicing.
• Never start the washer with any guards/
panels removed.
• Whenever ground wires are removed
during servicing, these ground wires must
be reconnected to ensure that the washer
is properly grounded. W003
WARNING
H067I
H068I

685945 7
Before You Start . . .
Tools
For most installations, the basic tools you will need are:
Electrical Requirements
Refer to serial plate for specific electrical requirements.
For more detailed information, refer to section on
Electrical Requirements.
Water Supply Requirements
Washer needs two standard 3/4 inch (19.1 mm) water
supply faucets with a pressure between 20-120 pounds
per square inch (138 to 827 kPa). For more detailed
information, refer to section on Water Supply
Requirements.
Installing the Washer . . .
Step 1:
Position Washer Near Installation
Area
Move washer so that it is within four feet of the desired
area of installation.
D074IE1H
LEVEL
SCREWDRIVER
PLIERS
WRENCH
SOCKET
WRENCH
9
/
1
6
"
H054IE1A

8685945
Step 2:
Connect Water Inlet Hoses
NOTE: Refer to section on Water Supply
Requirements before connecting water inlet hoses.
Remove the four plain rubber washers from accessories
bag, and install them according to the illustration.
Turn on the water supply faucets and flush the lines for
approximately two minutes to remove any foreign
materials that could clog the screens in the water mixing
valve.
NOTE: When installing in newly constructed or
renovated building, it is very important to flush the
lines since build-up may have occurred during
construction.
IMPORTANT: Thread hose couplings onto valve
connections finger-tight, then approximately 1/4 turn
with pliers. DO NOT cross thread or overtighten
couplings.
Turn water on and check for leaks. If leaks are found,
retighten the hose couplings. Continue tightening and
rechecking until no leaks are found.
RUBBER WASHER
(Plain)
H091IE1A
INSTALL THIS
END OF HOSE
TO WATER
SUPPLY FAUCET
INSTALL THIS END OF HOSE
TO VALVE CONNECTIONS
AT REAR OF WASHER
INLET
HOSE
RUBBER WASHER
(Plain)
H100IE1A
COLD WATER
CONNECTION
HOT WATER
CONNECTION
WATER SUPPLY
FAUCETS
WATER INLET
HOSES