Alliance Laundry Systems HFNKCASG113TN01 User manual

Programming
Frontload Washer
Refer to Page 9 for Model Identification
Insert
Coins/Ca rd
Wash Rinse Spin Door
Warm
Hot Cold
Delicate
Warm
Blankets
Cold
START
Extra
Rinse
Extra
Delicate
Cold
Wash
FLW2433N_SVG
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 806147ENR3
January 2019

WARNING
Failure to install, maintain, and/or operate this ma-
chine according to the manufacturer's instructions
may result in conditions which can produce bodily
injury and/or property damage.
W030
WARNING
For your safety and to reduce the risk of fire or an
explosion, do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or
any other appliance.
W022
NOTE: The WARNING and IMPORTANT instructions ap-
pearing in this manual are not meant to cover all possi-
ble conditions and situations that may occur. It must
be understood that common sense, caution, and care-
fulness are factors which cannot be built into these
washers. These factors MUST BE supplied by the per-
son(s) installing, maintaining, or operating the unit.
Always contact the distributor, service agent, or the manufacturer
about any problems or conditions you do not understand.
Read all instructions before using unit.
Hazardous voltage inside. Disconnect power before serv-
icing.
This product uses FreeRTOS V7.2.0 (www.freertos.org).
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3 Part No. 806147ENR3

Table of Contents
Model Identification............................................................................... 9
Preliminary Information.......................................................................10
About the Control......................................................................................... 10
Glossary of Terms.........................................................................................10
Power Failure Recovery................................................................................ 10
Communications...........................................................................................10
Infra-red Communications..........................................................................10
Serial Card Reader Communications (Card Models Only)............................. 10
Network Communications..........................................................................10
Control Identification............................................................................11
Select Cycle Pads..........................................................................................11
Select Cycle Modifier Pads............................................................................ 11
Display Identification............................................................................12
Light Emitting Diodes (LEDs)....................................................................... 12
CYCLE LED............................................................................................ 12
WASH LED..............................................................................................12
RINSE LED..............................................................................................12
SPIN LED................................................................................................ 12
Insert Coins/Card LED...............................................................................12
DOOR LED..............................................................................................12
Extra Wash LED....................................................................................... 12
Extra Rinse LED....................................................................................... 12
7-Segment Digits.......................................................................................... 12
Washer Operation.................................................................................13
Power Up.....................................................................................................13
Ready Mode.................................................................................................13
Partial Vend Mode........................................................................................ 13
Additional Vend Mode.................................................................................. 13
Start Mode................................................................................................... 13
End of Cycle Mode....................................................................................... 13
Door Locking Mode......................................................................................13
Door Unlocking Mode...................................................................................13
Cycle Sequence............................................................................................ 13
Closing Washer Door.................................................................................... 14
Signals.........................................................................................................14
Changing Cycles...........................................................................................14
© Copyright 2019, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4 Part No. 806147ENR3

Pause Mode..................................................................................................14
Delayed Start Setup (OPL Only).................................................................... 14
Delayed Start (OPL Only)..............................................................................14
Auto Flush Mode.......................................................................................... 15
Overflow Mode............................................................................................ 15
Power Failure Display Mode..........................................................................15
Special Features ...................................................................................16
Programming Control....................................................................................16
Collecting Audit Information......................................................................... 16
Testing Machine and Control Functions.......................................................... 16
Rapid Advance Feature................................................................................. 16
Clearing the Vend Feature .............................................................................16
Communications Mode..................................................................................16
Coin Drop.................................................................................................... 16
Start Pulse Operation.....................................................................................16
Service Door and Coin Vault Openings........................................................... 16
Special Vend.................................................................................................17
OPL Mode................................................................................................... 17
Out of Order Mode........................................................................................17
Error Display Mode...................................................................................... 17
Opening the Service Door..................................................................... 18
Stacked Washers and Dryers, 10 Degree Front Control Washers and Coin Rear
Control Washers........................................................................................18
Rear Control Washers with Card Reader......................................................... 18
Entering the Manual Mode................................................................... 20
How to Enter the Manual Mode......................................................................20
Manual Mode Navigation.............................................................................. 20
Programming Control...........................................................................22
What Can Be Programmed.............................................................................22
Programmable Options Available................................................................... 22
Vend Price 1 AtS 1........................................................................................36
Vend Price 2 AtS 2........................................................................................37
Vend Price 3 AtS 3........................................................................................37
Vend Price 4 AtS 4........................................................................................37
Vend Price 5 AtS 5........................................................................................37
Vend Price 6 AtS 6........................................................................................38
Cycle Modifier Key 1 Extra Wash Vend Price Adder ACNP 1...........................38
Cycle Modifier Key 2 Extra Rinse Vend Price Adder ACNP 2.......................... 38
Vend Price Decimal Point Ats dP....................................................................39
Coin 1 Value dEn 1....................................................................................... 39
Coin 2 Value dEn 2....................................................................................... 39
Start Pulse Value PLSE..................................................................................39
Start Pulse Mode PLSNod............................................................................. 40
Programmable Output Type AtyPE.................................................................40
Default Cycle dFtCyC................................................................................... 41
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5 Part No. 806147ENR3

Card Reader Display Control CArd................................................................ 41
Audio Signal AUdio......................................................................................41
How to Program the Audio Signal...............................................................42
How to Read Audio Signal Table................................................................ 42
Network Node Number nodE......................................................................... 43
Error Code Programming Error-..................................................................... 44
Low Water Level FL Lo................................................................................ 47
Medium Water Level FL NEd........................................................................ 47
High Water Level FL Hi................................................................................ 47
Flush Out Time for Fill Step FLSH t............................................................... 48
No Refill After Time for Agitate Step norF t....................................................48
Set Real-Time Clock rtC-...............................................................................48
Set Daylight Savings Time dLS-.....................................................................49
Special Vend 1 Days Enable SP1 1................................................................. 49
How to Read the Days Enable Value Table...................................................50
How to Program Special Vend 1 Start Minute SP1 2..................................... 55
How to Program Special Vend 1 Start Hour SP1 3........................................ 55
How to Program Special Vend 1 Start Date SP1 4.........................................55
How to Program Special Vend 1 Start Month SP1 5......................................55
How to Program Special Vend 1 Length in Hours SP1 7................................56
How to Program Special Vend 1 End Date SP1 8..........................................56
How to Program Special Vend 1 End Month SP1 9.......................................56
How to Program Special Vend 1 Vend Price 1 SP1 11................................... 56
How to Program Special Vend 1 Vend Price 2 SP1 12................................... 56
How to Program Special Vend 1 Vend Price 3 SP1 13................................... 56
How to Program Special Vend 1 Vend Price 4 SP1 14................................... 57
How to Program Special Vend 1 Vend Price 5 SP1 15................................... 57
How to Program Special Vend 1 Vend Price 6 SP1 16................................... 57
How to Program Special Vend 1 Wash Status Agitate Steps Added Minutes SP1
20.........................................................................................................57
How to Program Special Vend 1 Wash Status Agitate Steps Subtracted Minutes
SP1 21.................................................................................................. 58
How to Program Special Vend 1 Cycle Modifier Default Value SP1 22.......... 58
How to Program Special Vend 1 Cycle Modifier Extra Wash Key #1 Vend Price
SP1 23.................................................................................................. 58
How to Program Special Vend 1 Cycle Modifier Extra Rinse Key #2 Vend Price
SP1 24.................................................................................................. 58
How to Program Special Vend 1 Cycle Modifier Extra Wash Key #1 Options
SP1 25.................................................................................................. 58
How to Program Special Vend 1 Cycle Modifier Extra Rinse Key #2 Options
SP1 26.................................................................................................. 58
Special Vend 2 Days Enable SP2.................................................................... 59
Cycle Modifier Programming CNP-................................................................59
How to Program Default Cycle Modifier CNP 1...........................................59
How to Program Cycle Modifier Extra Wash Key #1 Options CNP 2............. 59
How to Program Cycle Modifier Extra Rinse Key #2 Options CNP 3.............61
How to Program Cycle Modifier Extra Wash Additional Wash Time CNP 4... 62
How to Program Cycle Modifier Extra Rinse Additional Rinse Time CNP 7...62
How to Enter Cycle Programming CyCLE-..................................................... 62
Programming the Fill Step Type..................................................................64
Programming the Supply Step Type............................................................ 65
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 Part No. 806147ENR3

Programming the Agitate Step Type............................................................ 67
Programming the Soak Step Type............................................................... 68
Programming the Drain Step Type.............................................................. 69
Programming the Extract Drain (Spin) Step Type......................................... 70
Programming the Audio Step Type..............................................................71
Programming the Hold Step Type............................................................... 72
Hold Step Custom Messages CNESS-.............................................................73
Programmable Cycle Time Display PCyCtd.................................................... 73
No Cycle Time Display nCyCtd..................................................................... 73
Number of Balance Attempts with No Loss of Time bAL At.............................73
Cycle Pause Resume CyCPAU....................................................................... 74
IR Access IrA En..........................................................................................74
Manual Rapid Advance rAPdEn.....................................................................74
Manual Diagnostics diAgEn.......................................................................... 74
Factory Test Ft En.........................................................................................75
Speed Units SUnitS.......................................................................................75
Vend Price Display Override AtS do............................................................... 75
OPL Parameters oPL-....................................................................................75
OPL Mode Enable oPL 1........................................................................... 76
OPL Delayed Start oPL 2...........................................................................76
OPL Display Power Save oPL 3................................................................. 76
Out of Order oUt...........................................................................................76
Collecting Audit Information................................................................ 78
How to Enter Audit Feature........................................................................... 78
Entering the Audit Feature by Manual Mode................................................... 78
Entering the Audit Feature with the Coin Vault Open....................................... 78
How to Read Audit Data................................................................................78
How to Exit Audit Feature............................................................................. 78
Manual Reset........................................................................................79
How to Enter Manual Reset .......................................................................... 79
Testing Machine and Electronic Control Functions............................... 80
How to Enter Testing Feature.........................................................................80
How to Start Tests.........................................................................................80
How to Exit Testing Feature ..........................................................................80
Diagnostic (Testing) Mode – Quick Reference Chart........................................ 80
Diagnostic Test Descriptions..........................................................................82
Control Software Version Number Test d 1.................................................. 83
Drive Board #1 Software Test d 3............................................................... 83
Water Level Trim Test d 7.......................................................................... 83
Service Door Opening Test d 8................................................................... 83
Coin Vault Opening Test d 9.......................................................................83
Coin Drop 1 Input Test d 10....................................................................... 83
Coin Drop 2 Input Test d 11........................................................................83
Vend Connection Header Present Test d 12.................................................. 83
Start Pulse Test d 13.................................................................................. 83
Door Switch Input Test d 15....................................................................... 84
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 Part No. 806147ENR3

Door Lock Input Test d 16..........................................................................84
Show Fill Time Test d 17........................................................................... 84
Show Drain Time Test d 18........................................................................ 84
Out of Balance Switch Test d 22................................................................. 84
External Outputs Test d 23......................................................................... 84
Water Purge Test d 24................................................................................ 84
Water Leak Detection Test d 25.................................................................. 84
Water Level Test d 26................................................................................ 85
DC Bus Voltage Test d 27...........................................................................85
AC Mains Voltage Test d 28....................................................................... 85
Configuration 1 Display Test d 29...............................................................85
Configuration 2 Display Test d 30...............................................................88
Configuration 3 Display Test d 31...............................................................88
Configuration 4 Display Test d 32...............................................................88
Configuration 5 Display Test d 33...............................................................89
Factory Test..................................................................................................89
To Enter Factory Test.................................................................................89
To Exit Factory Test...................................................................................90
................................................................................................................90
Error Codes .........................................................................................93
Rapid Advance Feature.......................................................................100
How to Enter Rapid Advance....................................................................... 100
How to Exit Rapid Advance Feature............................................................. 100
Clear Vend Feature............................................................................. 101
How to Clear Vend......................................................................................101
Power Fail Recovery........................................................................... 102
Communications Mode....................................................................... 103
Infra-red Communications........................................................................... 103
How to Begin Communications with an External Device.............................103
Card Reader Communications - Card Models Only........................................ 103
Network Communications............................................................................103
Default Cycle Time .............................................................................104
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8 Part No. 806147ENR3

Model Identification
Information in this manual is applicable to these washer models:
HFNKCASG113TN01 HFNKXASG113CN32
HFNKCASG113TN31 HFNKXASG113CW01
HFNKCASG113TN32 HFNKXASP113CN01
HFNKCASG113TW01 HFNKXASP113CN31
HFNKCASP113TN01 HFNKXASP113CN32
HFNKCASP113TN31 HFNKXASP113CW01
HFNKCASP113TN32 HFNKYASG113CN01
HFNKCASP113TW01 HFNKYASG113CN31
HFNKDASG113CN01 HFNKYASG113CN32
HFNKDASG113CN31 HFNKYASG113CW01
HFNKDASG113CN32 HFNKYASP113CN01
HFNKDASG113CW01 HFNKYASP113CN31
HFNKDASP113CN01 HFNKYASP113CN32
HFNKDASP113CN31 HFNKYASP113CW01
HFNKDASP113CN32 HFNZCASP113TN01
HFNKDASP113CW01 HFNZCASG113TN01
HFNKXASG113CN01 HFNZCASP113TN31
HFNKXASG113CN31 HFNZCASG113TN31
Model Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9 Part No. 806147ENR3

Preliminary Information
About the Control
This control is an advanced, programmable computer that lets the
owner control most machine features by pressing a sequence of
keypads.
The control allows the owner to program custom cycles, set vend
prices, retrieve audit information, run diagnostic tests, program
special vend features and set other programmable features. Wash-
ers shipped from the factory have a default cycle setting of Cold
built in. However, the owner can change the default cycle, or any
cycle, as needs permit.
IMPORTANT: In the event of a power failure, the control
will not have to be reprogrammed. It is designed with a
memory system that will remember how it was pro-
grammed until the electrical power is restored.
IMPORTANT: It is extremely important that the washer
has a good ground connection and that all mechanical
and electrical connections to the control are made be-
fore applying power to or operating the washer.
Glossary of Terms
The following are a few terms and abbreviations to learn. These
are referred to throughout the instructions.
Display – This term refers to the window area of the control that
displays words and values.
LED (Light Emitting Diode) – This term refers to the lights next
to the keypads and status words of the control.
FEC – Front End Control
I/O Board – Input/Output Board
OPL – On Premises Laundry
Power Failure Recovery
If a cycle is in progress and the power fails, the cycle status is
saved in memory. When the power recovers, the washer will re-
sume into the previously active cycle.
Communications
The control may be programmed manually or by infra-red with
an external device. A limited number of features can be program-
med by a card reader.
Infra-red Communications
An external device, such as a PDA, allows the owner to program
and retrieve information from the control without touching the
keypad. An external device greatly expands the programming op-
tions available to the owner. However, the external device is not
required to program and operate the machine. The operation of an
external device and the advanced features available are covered
separately in the instructions included with the external device
software. Contact Alliance Laundry Systems for a list of ap-
proved PDAs and other external devices.
Serial Card Reader Communications (Card Models
Only)
The control will accept communication with a serial card reader
in order to perform vending transactions when a card is inserted
to pay for cycles. The card reader can also allow the owner to
program a limited number of features and collect audit informa-
tion.
For detailed information on serial card reader communications,
refer to instructions included with card reader.
Network Communications
Network communication is available on models with Serial Num-
bers beginning 1706.
The control will also accept communication with a network inter-
face board which allows the control to be linked to a personal
computer. This network link allows an owner to program, collect
data and run diagnostics on any machine.
For detailed information on network communications, refer to the
network instructions.
Preliminary Information
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10 Part No. 806147ENR3