Allnet ALL02761 User manual

ALL02761
802.11g/802.11b Wireless Access Point
Broadband Internet Access
WPS
4-Port Switching Hub
Quick Install Guide
LThis guide covers only the most common
situations. Please refer to the full User Manual
on the CD-ROM if your LAN has any of the
following:
• Router
• Existing DHCP Server
• PCs using Fixed (Static) IP Addresses
P/N 957YGH0030 version1.1

Requirements
• DSL or Cable modem for broadband Internet access.
• Standard Network cables.
• TCP/IP network protocol installed on each PC.
• Wireless Access Point requires Wireless devices compli-
ant with the IEEE802.11b or IEEE802.11g specifications.
Setup
nPhysical Installation
1. Select a suitable place on the network to install the Wire-
less Router. Ensure the Wireless Router and the
DSL/Cable modem are powered OFF.
2. Use standard LAN cables to connect PCs to the Switching
Hub ports on the Wireless Router. Both 10BaseT and
100BaseT connections can be used simultaneously.
Page 1

3. Connect the DSL or Cable modem to the WAN port on
the Wireless Router. Use the cable supplied with your
DSL/Cable modem. If no cable was supplied, use a stan-
dard cable.
4. Power on the Cable or DSL modem.
Connect the supplied power adapter to the Wireless
Router and power up.
5. Check the LEDs
• The Power LED should be ON.
• For each LAN (PC) connection, the LAN LED should be
ON (provided the PC is also ON.)
• The WAN LED should be ON.
• The WLAN LED should be ON
oConfiguration
1. Start your PC. If it is already started, restart it.
It will then obtain an IP Address from the Wireless
Router's DHCP Server.
2. Start your WEB browser. In the Address box, enter the
following: HTTP://192.168.0.1
3. When prompted, use the following username and pass-
word.
• User name: admin
• Password: password
4. Click Setup Wizard on the menu.
5. Step through the Wizard until finished. Refer to the data
from your ISP, and the table below, to ensure your
choices are correct.
Page 2

Connection Type Data required.
Dynamic IP Address Usually, none.
But some ISP may require a par-
ticular Hostname, Domain name,
or MAC (physical) address.
Specified (Fixed)
IP Address IP Address allocated to you, and related information.
PPPoE Login name and password.
PPTP, Big Pond,
L2TP Login name and password,
Server Address
6. On the final screen of the Wizard, run the test and check
that an Internet connection can be established.
If the connection fails, check both your data and the
ADSL connection.
PC Setup - Windows
nTCP/IP Setup
• If using the default Wireless Router settings, and the
default Windows TCP/IP settings, no changes need to
be made.
• If using a specified (fixed) IP address on your PC, refer to
the user manual for details of the required changes:
• The Gateway must be set to the IP address of the
Wireless Router
• The DNS should be set to the address provided by
your ISP.
Page 3

oInternet Access
For Windows 98/ME/2000
1. Select Start Menu - Settings - Control Panel - Internet
Options.
2. Select the Connection tab, and click the Setup button.
3. Select "I want to set up my Internet connection manually,
or I want to connect through a local area network (LAN)"
and click Next.
4. Select "I connect through a local area network (LAN)"
and click Next.
5. Ensure all of the boxes on the following Local area net-
work Internet Configuration screen are unchecked.
6. Check the "No" option when prompted "Do you want to
set up an Internet mail account now?".
7. Click Finish to close the Internet Connection Wizard.
Setup is now completed.
For Windows XP
1. Select Start Menu - Control Panel - Network and Internet
Connections.
2. Select Set up or change your Internet Connection.
3. Select the Connection tab, and click the Setup button.
4. Cancel the pop-up "Location Information" screen.
5. Click Next on the "New Connection Wizard" screen.
6. Select "Connect to the Internet" and click Next.
7. Select "Set up my connection manually" and click Next.
8. Check "Connect using a broadband connection that is al-
ways on" and click Next.
9. Click Finish to close the New Connection Wizard.
Setup is now completed.
Page 4

Macintosh Setup
1. Open the TCP/IP Control Panel.
2. Select Ethernet from the Connect via pop-up menu.
3. Select Using DHCP Server from the Configure pop-up
menu. The DHCP Client ID field can be left blank.
4. Close the TCP/IP panel, saving your settings.
If using manually assigned IP addresses instead of DHCP, the
required changes are:
• Set the Router Address to the Wireless Router's IP Ad-
dress.
• Ensure your DNS settings are correct.
Linux Setup using X Windows
Follow this procedure to set your system to act as a DHCP
client and obtain an IP Address from the Wireless Router:
1. Start your X Windows client.
2. Select Control Panel - Network
3. Select the "Interface" entry for your Network card. Nor-
mally, this will be called "eth0".
4. Click the Edit button, set the "protocol" to "DHCP", and
save this data.
5. To apply your changes
• Use the "Deactivate" and "Activate" buttons
• OR, restart your system.
Page 5

Wireless Setup
In order to use the Access Point in the Wireless Router, other
Wireless devices must use the same SSID and Wireless Se-
curity settings as the Wireless Router.
The Wireless Router's default settings are as follows.
Setting Wireless Router
SSID Default value: default
This may be changed on the Wireless
screen, on the Wireless Router's main
menu.
Wireless
Security Default value: Disabled
Use the Wireless screen on the main menu
to change this as required.
Ensure the Wireless Router and the other Wireless Sta-
tions are using the same settings.
• Use the Wireless screen to configure the Wireless Access
Point in the Wireless Router.
• Configure the Wireless stations (PCs) using your normal
method for configuring the Wireless interface.
• Wireless Stations must also be set to use Infrastructure
mode.
• By default, the Wireless Router will automatically accept
both 802.11b and 802.11g connections.
Page 6