ALLOMATIC SL-175DC User manual

SL-175DC

TABLE OF CONTENTS
SAFETY AND INTRODUCTION
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
UL 325 Class Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INSTALLATION
Concrete Pad Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front and Rear Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Entrapment Protection Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Loop Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Gate Travel Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
BOARD FEATURES
Gate Opening Direction Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Programmable Relay and Leaf Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electronic Reversing Device (ERD) Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 14
Timer Adjustment and Radio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dip Switch Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LED Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
WIRING ACCESSORIES TO CONTROL BOARD
Accessory Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Monitored Entrapment Protection Device Connection. . . . . . . . . . . . . . . . . . 19-20
Loop Rack Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Three Button Station Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Master/Slave Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Magnetic/Solenoid Lock Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Radio Receiver Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
EMERGENCY RELEASE INSTRUCTIONS
Emergency Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SOLAR INSTALLATION
Solar Panel Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
External Solar System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ACCESSORIES AND PARTS BREAKDOWN
Pad Lock Tabs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

1
IMPORTANT SAFETY INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF :INJURY
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. DO NOT START INSTALLATION UNTIL
YOU HAVE READ AND UNDERSTAND THESE DIRECTIONS. IF THERE IS SOMETHING YOU DO NOT
UNDERSTAND, PLEASE CALL US.
NEVER let children operate or play with gate controls.
Locate the control station and make sure it is (a) within sight of the gate and (b) at a minimum height of 5
feet so small children cannot reach it.
Install the enclosed entrapment warning signs next to the control station and in a prominent location.
For operators equipped with a manual release, instruct the end user on the correct operation of the manual
release. Use the manual release only when the gate is not moving. It is advised that the power be turned
off.
Always keep people and objects away from the gate. No one should cross the path of a moving gate.
The gate operator must be tested monthly. The gate must reverse on contact with a rigid object, or stop
when an object activates the non-contact sensor(s). Always re-test the operator after adjusting the limits
and/or force. Failure to adjust and re-test the gate operator properly may cause sever injury or death.
Keep gate(s) properly maintained. Have a qualified service technician make repairs to gate hardware and
make proper adjustments to gate operator.
This gate entrance/exit is for vehicles only. Pedestrians must use a separate entrance.
There is nothing on a gate operator that is easily repaired or adjusted without a great deal of experience.
Call a qualified gate service technician who knows your gate operator.
SAVE THESE INSTRUCTIONS

2
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED)
BEFORE GATE OPERATOR INSTALLATION
ŸConfirm that the gate operator being installed is
appropriate for the application.
ŸConfirm that the gate is designed and built
according to the current published industry
standards.
ŸConfirm that all appropriate safety features and
safety accessory devices are being installed,
including all entrapment protection devices.
ŸMake sure that the gate opens and closes freely
(by hand) before installing the operator.
ŸRepair or replace worn or damaged gate
hardware before installing the gate operator.
ŸEliminate all gaps in the sliding gate below a 6
foot height that permits a 2 1/4” sphere to pass
through any location. This includes the area of
the adjacent fence covered when the gate is in
the open position
ŸEliminate all gaps in a swing gate below a 4 foot
height that permits a 4” sphere to pass through
any location. This includes the hinge area of the
gate.
GATE OPERATOR INSTALLATION
ŸOperator must be disconnected from the power
source before attempting any installation of
accessories.
ŸInstall gate operator according to the installation
instructions in this manual.
ŸAdjust the operator clutch or load sensing device
to the minimum force setting that will allow for
reliable gate operation.
ŸInstall the operator inside the fence line. Do not
install the operator on the public side of the fence
line.
ŸInstall a proper electrical ground to the gate
operator.
ŸControls intended for user activation must be
located at least 6 feet away from any moving part
of the gate, and where the user is prevented
from reaching over, under, around, or through
the gate to operate the controls.
ŸOutdoor or easily accessible controls shall have
a security feature to prevent unauthorized use.
ŸThe stop and/or reset button must be located in
the line of sight of the gate. Activation of the
operator reset control shall not cause the
operator to move.
ŸInstall a minimum of 2 warning signs, one on
each side of the gate where they are easily
visible.
ŸTake pictures of the installation.
ŸTest all safety features for proper function before
placing the automatic vehicular gate in
operation.
MAINTENANCE
ŸTrain owners/users on the basic functions and
safety features of the gate system, including
how to turn off the power and operate the
manual disconnect feature.
ŸLeave safety instructions, product literature,
installation manual, and maintenance manual
with the owner or end user.
ŸExplain to the owner or end user the importance
of routine service and operator testing on a
monthly basis.
INSTALL THE GATE OPERATOR ONLY WHEN YOU
HAVE READ THE FOLLOWING

3
UL 325 CLASS TYPES AND OBSTRUCTIONS SENSING SYSTEMS
UL 325 CLASS TYPES
CLASS ONE: RESIDENTIAL
ŸA vehicular gate operator intended for use in
garages or parking areas associated with a
residence of one to four single families.
CLASS TWO: COMMERCIAL OR GENERAL
PUBLIC ACCESS
ŸA vehicular gate operator intended for use at a
commercial location or building, such as a
multi-family housing unit (five or more single
family units), hotel, garages, retail stores, or
other buildings accessible by or servicing the
general public.
CLASS THREE: INDUSTRIAL OR LIMITED
ACCESS
ŸA vehicular gate operator intended for use at
an industrial location or building, such as a
factory, loading dock area, or other locations
not accessible by or intended to service the
general public.
CLASS FOUR: RESTRICTED ACCESS
ŸA vehicular gate operator intended for use at a
guarded industrial location or building, such as
airport security areas or other restricted
access locations not servicing the general
public and where unauthorized access is
prevented via supervision by security
personnel.
THE SIX TYPES OF OBSTRUCTION
SENSING SYSTEMS
TYPE A:
ŸInherent entrapment protection system. This
system must sense and initiate the reverse of
the gate within 2 seconds of contact with a
solid object.
TYPE B1:
ŸNon-contact sensor (photoelectric sensor or
equivalent). This system shall, upon sensing
an obstruction in the direction of the gate
travel, reverse the gate within a maximum of 2
seconds.
TYPE B2:
ŸContact sensor (edge device or equivalent).
This system shall, upon sensing an obstruction
in the direction of the gate travel, initiate the
reversal of the gate within a maximum of 2
seconds.
TYPE C:
ŸInherent force limiting, inherent adjustable
clutch, or pressure relief valve.
TYPE D:
ŸActuating device requiring continuous pressure
to maintain opening or closing motion of the
gate.
Each class must have (2) monitored entrapment protection devices in each entrapment zone to sense and react
to obstructions within 2 seconds.
All-O-Matic’s gate operators conform to the most rigid Class One.

4
6 11/16”
6 11/16”
SIX RED HEAD
BOLTS 1/2” X 3 1/2”
17.25”
20”
20”
30”
14”
27 3/4”
10”
SL-175 DC CONCRETE PAD

5
FRONT MOUNT INSTALLATION
DRIVEWAY
GATE CLOSED
GATE OPERATOR TRACK FOOTING
OPERATOR FOOTING
FRONT VIEW
OVERHEAD VIEW
TRACK FOOTING
OPERATOR FOOTING
GATE IN OPEN POSITION

6
27 3/4”
14”
TOTAL COVER
HEIGHT
DRIVE CHAIN
LEVEL
TOP OF
OPERATOR PAD
FRONT MOUNT INSTALLATION (CONTINUED)

7
REAR MOUNT INSTALLATION
DRIVEWAY
GATE IN OPEN POSITION GATE CLOSED
GATE OPERATOR
OPERATOR FOOTING
OPERATOR FOOTING
TRACK FOOTING
TRACK FOOTING
FRONT VIEW
OVERHEAD VIEW
GATE OPERATOR
FOOTING
MOVE ONE IDLER
TO THE BOTTOM
CENTER HOLE AND
FOLLOW THE
CHAIN PATH
AS SHOWN
CHAIN PATH
GATE POST
FRONT IDLER
SAFETY GUARD
GATE
CHAIN CONNECTION TO GATE

8
ENTRAPMENT PROTECTION INSTALLATION
ŸA minimum of (2) monitored entrapment protection devices are REQUIRED for each entrapment zone.
ŸAn entrapment zone is a location or point of contact where a person can become entrapped between a moving
gate and a rigid object.
ŸThe operator is equipped with an inherent entrapment protection system (ERD).
ŸThe gate operator requires an external monitored entrapment protection device (non-contact photoelectric
sensor or contact edge) for each entrapment zone prior to gate operation. The operator cycles power to the
external entrapment protection device and checks for device signals. If the operator does not receive the
correct feedback from the device, the gate will not operate.
ENTRAPMENT ZONE
ENTRAPMENT ZONE
ENTRAPMENT ZONE
INSIDE PROPERTY
INSIDE PROPERTY
OUTSIDE PROPERTY
OUTSIDE PROPERTY
OVERHEAD VIEW
FRONT INSTALLATION
REAR INSTALLATION
OVERHEAD VIEW
PHOTOELECTRIC
SENSOR
PHOTOELECTRIC
SENSOR
CONTACT EDGE
SENSOR
CONTACT EDGE
SENSOR
PHOTOELECTRIC
SENSOR
PHOTOELECTRIC
SENSOR
ENTRAPMENT ZONE

9
LOOP LAYOUT
1/4 IN
1 1/2 IN
SAFETY LOOP
WHEN USED
EXIT LOOP
4 FT 4 FT
8 FT
8 FT
4 FT4 FT
4 FT
GATE OPERATOR
GATE
GATE TRACK
TWISTED 6 TURNS
PER FOOT
NOTE: IF WIRES ARE
NOT TWISTED, LOOP
WILL MALFUNCTION.
WIRED IN SERIES
OUTSIDE PROPERTY
SAFETY LOOP
— Below is a typical loop layout. When connecting to an All-O-Matic circuit board, use the following:
— Safety Loop - Normally Closed (N.C) Contacts
— Exit Loop - Normally Open (N.O.) Contacts
— Wires MUST be twisted from the exit point of the loop saw cut to the gate operator.
—Twist loop wires 6 turns per foot, as shown below. Improper twisting of wires can cause loop issues.
— When using an inside and outside safety loop, loops must be WIRED IN SERIES.
INSIDE PROPERTY

10
ELECTRICAL CONNECTION
ŸAll gate operators MUST be properly grounded. This minimizes or prevents damage due to electrical charge,
such as a near lightening strike or an electrical static discharge.
ŸUse a single wire for the ground. DO NOT splice two wires for the ground. If the wire breaks or is cut, replace it
with a single length wire. NEVER use two wires for the ground.
ŸCheck the local city code for proper earth ground rod type and grounding procedures.
OPERATORS MUST BE PROPERLY GROUNDED!
230V
115V
GRD LINE 1 LINE 2
ŸUse a minimum of a 20-amp, dedicated circuit for power.
Power Connection
115 VAC
220 VAC Single Phase
LINE 1
115V HOT
220V LINE 1
LINE 2
115V NEUTRAL
220V LINE 2
GND
GROUND
GROUND
POWER AND BATTERY
SWITCHES
NOTE: WHEN APPLYING
230V TO THE OPERATOR,
MAKE SURE VOLTAGE
SWITCH IS FLIPPED TO 230V
POWER BOARD

11
GATE TRAVEL ADJUSTMENT
EACH NOTCH
EQUALS ABOUT
1/2” OF TRAVEL
LIMIT NUTS
LIMIT SWITCH
LIMIT NUT LOCK PLATE
Locate the limit switches (limit switches will be in the limit box on SL-150 DC) and follow the steps below:
1: Turn the power OFF on the operator.
2: Push the limit lock plate down (on the SL-45 DC, SL-90 DC, and SL-100 DC) or outwards (on the
SL-150 DC)
3: Turn the limit nut in the desired direction.
(Toward the switch to decrease travel and away from the switch to increase travel)
4: Place limit plate back to its locked position. (MUST be done for gate to hold its limits)
5: Turn the power ON on the operator.
6: Run the gate operator open and close. If additional adjustment is needed, repeat the steps.

12
GATE OPENING DIRECTION SETTING
LEDs WILL SHOW
OPENING OR
CLOSING DIRECTIONS
WHEN THE GATE IS
RUNNING
Ÿ Use OPEN L/R” dipswitch (#8) to change the opening direction of the operator.
Ÿ The direction of gate opening is determined from behind the gate operator.
Ÿ LEDs will show opening and closing direction when the gate is moving.
ŸOPEN L/R switch “OFF” is for left hand opening
ŸOPEN L/R switch “ON” is for right hand opening
OPEN TO THE RIGHT OPEN TO THE LEFT
1001 1001 1001 1001
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
C8RB
LMC64
82AIM
C8RB
LMC64
82AIM
58ADC1K G4
Ls07
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001 1001 1001
1001 1001
1001
1001
1001
00
00
1001
1001
1001 1001
1002 1002 1002 1002 1002 1002 1002 1002 1002 1002 1002
1002
1002
1002
1002
2262
2262
2262
2262
2262
2262
2402
2402
2402
2402
2402
2402
2402
20M
90R9
10R0
1000
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
476E
900R3
476E
900R3
5W
.01
I0615
I/
O
710
710
710
710
710
710
710
710
710
710
SS
14
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
602
S26
S
602
S26
S
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
ATMEL
ATMEGA168
20AU 0743
MAAF
S21B
101. we
100
HFK.
7J2
100
HFK.
7J2
33
HFK
5GN
DR127-330
43CL07 E
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
C8RB
LMC64
82AIM
1001
0022
1001
1001 1001
1001 1001
1001
1001
1001
1001
0022
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
1 2
OPEN
3
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
VAGEO 1442
10W 11R J
30

13
PROGRAMMABLE RELAY AND LEAF DELAY
Board model ALL-BLDC-REV-X6 includes a programmable relay (N.O.) with four different configurations.
See table below for switch settings. Use the “Leaf Delay” potentiometer to adjust the delay time from
0 to 6 seconds.
(1) 1 second pulse for every open start cycle
- Typically used for a cycle counter
(2) “ON” when the gate is in motion
- Typically used for an audible alarm or strobe light to warn when the gate is in motion
(3) Alarm system output
- Activates the relay when the gate is forced open
(4) “ON” when gate is not fully closed
- Typically used for an indicator
S1
S2
RELAY FUNCTION
OFF
OFF
ONE SECOND PULSE FOR EVERY OPEN START CYCLE
ON
OFF
ON WHEN GATE IS IN MOTION
OFF
ON
ALARM SYSTEM OUTPUT
ON
ON
ON WHEN GATE IS NOT FULLY CLOSED
1 2
OPEN
3
DEVICE
DEVICE
POWER SUPPLY
13
DELAY
0 TO 6 SECOND DELAY ADJUSTMENT
DIP SWITCH 3
DELAY FUNCTION SETTING
C8RB
LMC64
82AIM
C8RB
LMC64
82AIM
58ADC1K G4
Ls07
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001 1001 1001
1001 1001
1001
1001
1001
00
00
1001
1001
1001 1001
1002 1002 1002 1002 1002 1002 1002 1002 1002 1002 1002
1002
1002
1002
1002
2262
2262
2262
2262
2262
2262
2402
2402
2402
2402
2402
2402
2402
20M
90R9
10R0
1000
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
476E
900R3
476E
900R3
5W
.01
I0615
I/
O
710
710
710
710
710
710
710
710
710
710
SS
14
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
602
S26
S
602
S26
S
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
ATMEL
ATMEGA168
20AU 0743
MAAF
S21B
101. we
100
HFK.
7J2
100
HFK.
7J2
33
HFK
5GN
DR127-330
43CL07 E
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
C8RB
LMC64
82AIM
1001
0022
1001
1001 1001
1001 1001
1001
1001
1001
1001
0022
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
1 2
OPEN
3
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
VAGEO 1442
10W 11R J
30

14
ELECTRONIC REVERSING DEVICE (ERD) ADJUSTMENT
All DC boards are equipped with an Electronic Reversing Device (ERD), which will cause the gate to reverse
direction when it comes into contact with an obstruction.
The amount of force required to reverse the gate’s direction depends on the ERD sensitivity setting and
motor rating. Make sure that the ERD jumper is set to the correct pin setting (see chart below).
If the gate reverses direction on its own without hitting an obstruction, the ERD is too sensitive. If the gate
does not reverse when it hits an obstruction, the ERD is not sensitive enough.
COUNTER CLOCKWISE
MAXIMUM SENSITIVITY
(LESS FORCE TO STOP GATE)
CLOCKWISE
MINIMUM SENSITIVITY
(MORE FORCE TO STOP GATE)
C8RB
LMC64
82AIM
C8RB
LMC64
82AIM
58ADC1K G4
Ls07
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001 1001 1001
1001 1001
1001
1001
1001
00
00
1001
1001
1001 1001
1002 1002 1002 1002 1002 1002 1002 1002 1002 1002 1002
1002
1002
1002
1002
2262
2262
2262
2262
2262
2262
2402
2402
2402
2402
2402
2402
2402
20M
90R9
10R0
1000
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
476E
900R3
476E
900R3
5W
.01
I0615
I/
O
710
710
710
710
710
710
710
710
710
710
SS
14
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
602
S26
S
602
S26
S
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
ATMEL
ATMEGA168
20AU 0743
MAAF
S21B
101. we
100
HFK.
7J2
100
HFK.
7J2
33
HFK
5GN
DR127-330
43CL07 E
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
C8RB
LMC64
82AIM
1001
0022
1001
1001 1001
1001 1001
1001
1001
1001
1001
0022
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
1 2
OPEN
3
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
VAGEO 1442
10W 11R J
30
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
1001
1001
1001 1001

15
TIMER ADJUSTMENT AND RADIO SETTING
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
TIMER
RADIO
OSC
LOCK
1-PASS
SLAVE
BRAKE
OPEN L/R
OFF ON
RADIO “ ” = ON ALLOWS THE
TRANSMITTER TO CLOSE
THE GATE BEFORE THE TIMER
TIMER “ ” TO ON
ACTIVATE THE TIMER
TIMER ON: Automatic timer to close can be set from 1 to 60 seconds
TIMER OFF: Gate operation is “push button to open, push button to close”
RADIO ON: To override the timer and allow the radio receiver to close the gate before the timer
Turn potentiometer counter clockwise for more time
Turn potentiometer clockwise for less time
60
SEC
0
SEC
60
SEC
0
SEC
NOTE: The timer may not activate to close the gate if the potentiometer is turned all the way counter clockwise
C8RB
LMC64
82AIM
C8RB
LMC64
82AIM
58ADC1K G4
Ls07
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001 1001 1001
1001 1001
1001
1001
1001
00
00
1001
1001
1001 1001
1002 1002 1002 1002 1002 1002 1002 1002 1002 1002 1002
1002
1002
1002
1002
2262
2262
2262
2262
2262
2262
2402
2402
2402
2402
2402
2402
2402
20M
90R9
10R0
1000
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
476E
900R3
476E
900R3
5W
.01
I0615
I/
O
710
710
710
710
710
710
710
710
710
710
SS
14
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
602
S26
S
602
S26
S
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
ATMEL
ATMEGA168
20AU 0743
MAAF
S21B
101. we
100
HFK.
7J2
100
HFK.
7J2
33
HFK
5GN
DR127-330
43CL07 E
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
C8RB
LMC64
82AIM
1001
0022
1001
1001 1001
1001 1001
1001
1001
1001
1001
0022
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
1 2
OPEN
3
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
VAGEO 1442
10W 11R J
30
13

16
DIP SWITCH FUNCTIONS
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
TIMER
RADIO
OSC
LOCK
1-PASS
SLAVE
BRAKE
OPEN L/R
OFF ON
NOTE: IF ANY CHANGES ARE
MADE TO THE DIPSWITCHES
WITH THE POWER ON, PRESS
THE MAIN RESET BUTTON TO
RECOGNIZE THE CHANGE.
TIMER
TIMER switch “ON” activates the automatic close
timer.
RADIO
RADIO switch “ON” allows the radio receiver to
override the automatic close timer.
OSC
OSC switch “ON” allows the radio receiver to stop
and reverse the gate in any direction. During a cycle,
the first signal stops the gate. A second signal
reverses the gate.
LOCK
LOCK switch “ON” is used when a mag lock is
installed. “OFF” is used when a solenoid lock is
installed or no lock is installed.
1-PASS
1-PASS switch “ON” allows the gate to open until
one vehicle goes over the safety loop. Once the
vehicle has cleared the loop, the gate will stop and
close. If a second vehicle goes over the loop while
the gate is closing, the gate will stop. The vehicle
must get off of the loop before the gate continues to
close, forcing the second vehicle to present valid
credentials. This is a true one pass, anti-tailgating
feature to be used with safety loops.
SLAVE
This feature is used in dual gate applications. The
SLAVE switch will be “ON” only on the slave
operator. All other dip switches will be “off”. SLAVE
switch will be “OFF” on the master operator. Set
desired dip switch settings on the master operator
only.
BRAKE
BRAKE switch “ON” assists in stopping the gate at
the moment of contact between the limit nut and
limit switch. This function should only be used on
uphill or downhill applications. A 20-amp dedicated
circuit breaker should be used when this switch is on.
OPEN L/R
OPEN L/R switch “ON” is used for right hand
opening of the gate. The “OFF” position is used
for left hand opening of the gate.
C8RB
LMC64
82AIM
C8RB
LMC64
82AIM
58ADC1K G4
Ls07
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001
1001 1001 1001 1001
1001 1001
1001
1001
1001
00
00
1001
1001
1001 1001
1002 1002 1002 1002 1002 1002 1002 1002 1002 1002 1002
1002
1002
1002
1002
2262
2262
2262
2262
2262
2262
2402
2402
2402
2402
2402
2402
2402
20M
90R9
10R0
1000
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
1501
476E
900R3
476E
900R3
5W
.01
I0615
I/
O
710
710
710
710
710
710
710
710
710
710
SS
14
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
90R9
10R0
1000
SS
14
829B
R616
602
S26
S
602
S26
S
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
IR2110S
0618 IOR
ATMEL
ATMEGA168
20AU 0743
MAAF
S21B
101. we
100
HFK.
7J2
100
HFK.
7J2
33
HFK
5GN
DR127-330
43CL07 E
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
CMX-309FB C
8.0000 M
535202
C8RB
LMC64
82AIM
1001
0022
1001
1001 1001
1001 1001
1001
1001
1001
1001
0022
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
F
MOC8050
629Q
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
O
U
R
N
3
8
6
B
S
3
13
1 2
OPEN
3
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
710
KE.
1 2 3 4 5 6 7 8
-----------------------OPEN------------------------
VAGEO 1442
10W 11R J
30
RESET

17
LED DIAGNOSTICS
MODE
Blinks slowly (about every 2 seconds) when an
overload or over current occurs. Blinks rapidly (about
every 1/2 second) when the gate is jammed or the
motor sensors are not responding or are disconnected.
RADIO
ON when the RADIO input is activated (closed circuit
to common).
EXIT
ON when the EXIT input is activated (closed circuit to
common).
PHANTOM LOOP
ON when the PHANTOM LOOP input is activated
(closed circuit to common).
SAFETY LOOP
ON when the SAFETY LOOP input is activated (open
circuit to common)
STOP CMD
ON when the STOP CMD input is activated (open
circuit to common)
MON_OPEN
ON when the MON-OPEN input is activated (open
circuit to open) or when a device is not installed.
MON_CLOSE
ON when the MON_CLOSE input is activated (open
circuit to common) or when a device is not installed.
TIMER
Blinks when the timer is counting down to close
automatically.
CLOSE-CMD
ON when the CLOSE-CMD input is activated (closed
circuit to common).
CLOSING
ON while the gate is in the close cycle.
OPENING
ON while the hate is in the open cycle.
CLOSE-LIMIT
ON while the limit nut is activating the close limit
switch.
OPEN-LIMIT
ON while the limit nut is activating the open limit
switch.
LOW-BATTERY
ON when the batteries are low.
ALARM
Blinks every 30 seconds (alarm will also beep) when
the batteries are low, bad, or disconnected. Turns on
for 5 minutes (alarms also goes off) when the operator
goes into shut down mode due to the gate hitting an
obstruction (ERD).
M/S LINK
ON when master/slave communication is active.
AC/PWR ON
ON when AC power is on.