Almost Heaven Saunas Rainelle Operating instructions

Almost Heaven Saunas
THE AUTHENTIC SAUNA EXPERIENCE
®
Rainelle Sauna
Installation &
Owner’s Manual

Read this entire manual through to the end before proceeding with the assembly.
RAINELLE SAUNA INSTALLATION & OWNER’S MANUAL
Thank you for your purchase of your Rainelle Sauna. Should you have any questions during assembly,
please feel free to give us a call at 888.355.3050, or email [e-mail].
Regular business hours are 9-5 EST, M-F.
Your Rainelle Indoor Sauna is specically designed to utilize your existing oor. As such, assembly is made
very simple since the entire sauna sits on pre-fabricated rails and risers rather than on a oor platform. Your
sauna can be assembled on any surface that is rm and at, including concrete, ceramic, vinyl, laminate or
tile. (Installation on a carpeted surface is not recommended.) If you prefer a wood oor inside your sauna,
please visit our website at almostheaven.com to investigate our red cedar oor kits!
Almost Heaven Saunas
THE AUTHENTIC SAUNA EXPERIENCE
®
c4 oor risers
c 4 Wall Support Rails
c 4 Roof Support Rails
c 2 Roof Sections
c Wall Section A
c Wall Section B
c Wall Section C
c Wall Section D
c Wall Section E
c Window Section F
c Door Section G
c Wall Section H
c Upper Bench
c Lower Bench
c Backrest w/LED light
c LED Power Supply
c Doorknob Assembly
c Bucket and Ladle
c Heater
c Stones
c Thermometer/Hydrometer
c Wall Sensor Cover
c Hardware Bag containing:
2” screws, 2.5”Bench Screws, and Trim nails
c Heater Fence Kit
Your Rainelle kit should include the following:
RAINELLE SAUNA INSTALLATION MANUAL
page 1
These tools are required to assemble your Rainelle sauna:
cCordless drill
cTape measurer
cRubber mallet
cHammer
c1/2” or 5/8” Forstner Bit
cUtility Knife
cScrewdriver (Phillips and Flathead)
cLevel
cStep stool or ladder
cFraming square

Step 1. Connect the 4 Floor Risers
Fasten the 4 oor risers together using the pre-drilled holes as a guide, being sure the 2 shorter boards are located on the sides and the 2 longer
boards are on the front and back. (Images 1-4) Use a framing square to ensure the assembly is square.
Step 2. Position Wall Support Rails
Align each wall support so that the angled cuts make a corner, placing the shorter supports on the sides and the longer supports on the front and
back. Each wall support has one angled predrilled hole. Fasten the front, back, and sides together (Image 5 -7) and lay the assembly squarely on
top of the oor risers with the groove facing up (Image 8). The rails should overlap both sides of the riser by approximately 1” (Image 9). Secure the
assembly to the oor risers using 3 screws evenly spaced on each wall support rail (Image 10).
Step 3. Position Wall Sections A & B
Position wall section A in the groove of the left rail and push it ush against the back rail (Image 11). Having a helper hold wall section A, orient
wall section B so that the vent holes are on top and place it in the groove of the back rail. Push the at edge ush against wall section A. Align
the two panels so their edges are ush (Image 12) and fasten them together using the 2”screws (Image 13).
Image 1 Image 2 Image 3 Image 4
RAINELLE SAUNA INSTALLATION MANUAL
page 2
Image 5 Image 6 Image 7
Image 8 Image 9 Image 10
Image 11 Image 12 Image 13

Step 4. Position wall sections C & D
Position wall section C into the groove of the back rail. Attach it to wall section B by way of the tongue and groove t (Image 14). Secure it into place
by tapping section C with a rubber mallet (Image 15). Position wall section D onto the side rail (Image 16), pushing it ush against the back rail so
that it overlaps the at end of wall section C. Fasten wall section D to C using 2” screws and pre-drilled holes (Images 17 & 18)
Step 5. Bench & LED Backrest Installation
Note: You may choose to install benches and backrest after the sauna is completed, though you may nd it easier to install with the extra space
and light aorded at this step.
Place the wider upper bench on the pre-installed upper bench supports and push it against the back wall, being sure the side of the bench with
the screws showing is oriented towards the back (Images 19 & 20). Secure the bench to the back and side panels using the 2.5”bench screws and
the predrilled holes in the bench frame supports (Image 21). Repeat this process for the lower bench, aligning the face of the bench frame ush
with the front edge of the pre-installed lower bench supports (Images 22& 23). Fasten the lower bench to the side panels using the 2.5”fasteners.
Center the LED backrest between the two side panels being sure it’s oriented so the shorter slat is down and position it vertically at the height
most comfortable to you. Using a level to ensure proper installation, fasten the backrest into place using the 2” fasteners (Images 24 & 25).
To connect the LED light to the power source, bore a 5/8”hole through the back panel at the bottom right corner of the backrest and push the
LED pigtail through (Images 26 & 27). Mount the power supply to the back of your sauna at the base of panel C, directly underneath the hole you
just bored. Connect the power supply and LED pigtail, and plug in the supply to an outlet. (Images 28 & 29) You are able to turn on the LED light
and adjust its brightness from within the sauna using the control mounted to the side of the backrest.
RAINELLE SAUNA INSTALLATION MANUAL
page 3
Image 14 Image 15 Image 16 Image 17 Image 18
Image 19 Image 20 Image 21 Image 22
Image 23 Image 24 Image 25 Image 26 Image 27
Image 28 Image 29
orient to
back

Step 6. Position Wall Section E & H
Position wall section E into the groove of the side rail, orienting it so the 4 heater vent holes are located at the bottom (Image 30). Wall section E
attaches to wall section D by means of a tongue and groove t so there is no need for screws. Slide securely into place, tapping it in with a rubber
mallet (Image 31). Position wall section H into the groove on the opposite side rail (Image 32). Wall section H attaches to wall section A by means
of a tongue and groove t so there is no need for screws. Slide it securely into place, tapping it in with a rubber mallet (Image 33).
Step 7. Position Wall Sections F & G
Gently position wall section F into the front rail, orienting it so the faded glass is at the bottom. Push wall section F ush against wall section E
(Image 34). Being sure there is no overlap between sections E & F, fasten them together with 2”screws and predrilled holes located on the outside
of wall section E (Image 35).
Gently position wall section G (door) onto the wall support, orienting it so the faded glass is at the bottom. Slide the tongue of section G into the
groove of section F until the panel drops into the groove of the wall support (Image 36). Being sure there is no overlap between sections G & H,
fasten them together with 2”screws through the pre-drilled holes on the exterior of wall section H (Image 37).
Step 8. Position Roof Support Rails
Align each roof support rail so that the angled cuts make a corner, placing the shorter supports on the sides and the longer supports on the front
and back. Each roof support has one angled predrilled hole; use this to fasten the front, back, and sides together just as you did in step 2 for the
wall support rails (Images 38 & 39). Use a framing square to ensure the assembly is square. Lay the assembly on top of the sauna walls with the
groove facing down. Align the assembly on top of the sauna so that the tops of the wall sections t snugly in the groove. When in place, fasten the
roof support to the walls using three 2” screws for each rail (Image 40).
RAINELLE SAUNA INSTALLATION MANUAL
page 4
Image 30 Image 31 Image 32 Image 33
Image 34 Image 35 Image 36 Image 37
Image 38 Image 39 Image 40

Step 9. Position Roof Panels
Place the roof panels on top of the ceiling supports being sure the pre-drilled holes are facing up (Image 41). Insert the tongue of one panel into
the groove of the other (Image 42). Measure around the roof support rails to be sure the panels are spaced evenly around the top of the sauna;
approximately 1” of the support rails should extend past each side of the roof panels (Image 43). Secure them to the roof support rails using the 2”
screws through the pre-drilled holes (Image 44).
Using the 1” trim nails, secure the decorative trim pieces to the front and back of the ceiling panels (Image 45).
Step 10: Accessories
1. Install the vent-hole cover using the provided screw and washer (Images 46 & 47).
2. Hang the thermometer/hydrometer on the opposite wall of the heater 12 to 15 inches below the ceiling (Image 48).
3. Unwrap bucket and ladle and set in sauna (Image 49) .
4. Install the optional trim pieces to cover the joint between panels F & G by gently nailing the board in place using the 1”nails (Image 50).
5. Install doorknob (Image 51)
After the sauna has been installed, sweep down the inside to remove any sawdust and wood shavings, and then vacuum completely. Using a
damp cloth and warm water, wipe down the entire sauna including the benches to remove any remaining dirt, dust and debris.
Step 11: Heater Installation
Please consult your heater manual for all heater installation information. All electrical connections must be done by a qualied licensed
electrician.
RAINELLE SAUNA INSTALLATION MANUAL
page 5
Image 41 Image 42 Image 43 Image 44 Image 45
Image 46 Image 47
Image 48
Image 49
Image 50 Image 51

TRADITIONAL SAUNA USE
Congratulations! You are ready to enjoy your sauna! You may use your sauna in a wet or dry fashion. A dry sauna means
you do not sprinkle any water onto the stones, while wet means you increase the humidity of the room by sprinkling
water on the stones. Please note that not much water is needed to achieve a wet sauna experience.
The sauna as we know it originates in Finland. The typical sauna experience follows the steps below, but you may enjoy
your sauna in any way you like!
• Setyourheatersoyoursaunaachievesthedesiredtemperature.Thisistypically150-170+degreesF.Pleasenote,
novice sauna users should begin at the lower end of that range and increase their high temperature over time.
• Takeaquickshoweroraquickdipinahottuborpool.
• Step into the sauna and enjoy for 5-15 minutes, bringing a towel to sit or lay on. Leave the sauna once you are
perspiring freely.
• Takeaplungeinapool,shower,snowbank,lake-anythingthatwillcoolyoudown!Afterthat,relaxandcooldown
for 10-20 minutes.
• Stepintothesaunaagain.Duringthisvisit,youmaywishtosprinklesmallamountsofwaterontothestonesto
create bursts of steam. If water spills through the heater to the oor, you are using too much water, though this will
not hurt the heater or the sauna.
• Continuerepeatingthisprocess.Afteryournalvisittoyoursauna,relaxforatleast20minutes.Showerwithwarm
water initially, nishing with cool water to close your skin pores.
• Preparetofeelrefreshedforthedayortohaveanamazingnight’ssleep!
Whatever your sauna routine, it is imperative that you STAY HYDRATED!
Almost Heaven Saunas
THE AUTHENTIC SAUNA EXPERIENCE
®
RAINELLE SAUNA INSTALLATION MANUAL
page 6