Almost Heaven Saunas Radiant Series Operating instructions

Radiant Series Infrared
Sauna Installaon &
Owner’s Manual
April 2016

Read this enre manual through to the end before beginning assembly.
Thank you for your purchase of your Radiant Series Infrared Sauna. Should you have any quesons during assembly, please feel
free to give us a call at 888.355.3050, or e-mail [e-mail]. (Regular business hours 9-5 EST, M-F.)
This manual applies to the LX1, LX2, and LX3 infrared sauna models. The panels and bench sizes will be dierent, but assembly is
the same. We recommend watching the provided assembly video too.
To get started, you’ll nd all necessary assembly hardware under the Dust Cover aached
to the Roof Panel.

2. Posion the Floor Panel
Place the Floor Panel on a level surface. The Floor Panel is
labeled to indicate front vs. back. To avoid damaging your
oor, do not move the sauna aer assembly; prior to
assembly, select a locaon within reach of a power outlet
and pay aenon to the orientaon of the door to make
sure nothing will block it.
3. Place the Back and Le Panels
The Back Panel is disnguished by the Bench Support mount.
Have someone hold the Back Panel in place while you
posion the Le Panel. (The Le Panel should sit all the way
back and overlap the edge of the Back Panel.) Using the
provided screws and the pre-drilled holes, screw the Le
Panel into the Back Panel.
1. Lay out All Sauna Components
Package includes Floor Panel, mulple Wall Panels, pre-
assembled Bench Secons, Roof Panel with Dust Cover, and
Top Front Plate. Make sure that the Wall Panels are right
side up. The top of each panel is disnguished by the Roof
Panel Support edge; addionally, the pre-posioned cords
supplying power to the carbon ber heang panels will
emerge from the sauna at the top.
4. Place the Right Panel
The Right Panel is disnguished by its decorave groove at
the top. It is also thicker than the le panel and has a small
groove on the outside-facing wall. Posion the Right Panel
so that it sits all the way back and overlaps the edge of the
Back Panel. Using the provided screws and the pre-drilled
holes, screw the Right Panel into the Back Panel.
NOTE: You may choose to do Step 5 or Step 6 rst according
to your personal preference.
5. Place the Front Panel
The Le Panel will overlap the edge of the Front Panel, and
the Front Panel will overlap the edge of the Right Panel.
Using the provided screws and the pre-drilled holes, screw
the Le Panel into the Front Panel and the Front Panel into
the Right Panel.
Separate the door handles and reaach to the door, one
handle on each side.
Bench Support mount
Roof Panel Support edge

6. Install the Bench
The Bench comes in two porons: the Front Bench Secon
and the Top Bench Secon. Insert the Front Bench Secon
into the notch in the Le and Right Panels to hold it in place.
Connect the power supply for the lower carbon ber heang
panel pre-installed on the Front Bench Secon.
Next, take the Top Bench Secon and slide it into place so
that the front edge sits rmly on the Front Bench Secon
and the back edge sits on the Rear Bench Support mount
(referenced in Step 3). Secure the Top Bench Secon by
using (4) provided screws and the pre-drilled holes.
7d. Install the Roof Panel
Next, connect the heater plugs to their correspondingly
labeled plugs as well as the labeled light and audio plugs.
8. Install the Roof Front Plate
The Roof Front Plate will pop into posion in the gap
remaining between the Front Panel and the Roof Panel.
(Arrows indicate which side should be facing the front.)
Connect the front pre-posioned power cord. Replace the
Dust Cover that you removed in Step 7.
7a. Install the Roof Panel
First, make sure all of the top pre-posioned cords are
draped so that they hang outside the sauna.
7b. Install the Roof Panel
If you haven’t done so already, completely remove the Dust
Cover from the Roof Panel and place it to one side.
7c. Install the Roof Panel
Posion the Roof Panel so that it’s resng on the Roof Panel
Support edge (referenced in Step 1). On the inside of the
sauna, you’ll noce a decorave gap between the Top and
Wall Panels.

9. Install Screw Covers (oponal)
Use a hammer to tap the provided screw covers into the pre-
drilled holes in the Wall Panels to give the sauna a seamless
nish.
10. Connect to Power Source
Your sauna plugs directly into a 110V, 20 Amp dedicated
outlet.
Operang Instrucons
Follow these instrucons for operaon of your Radiant Infrared Sauna.
CONTROL PANEL
All functions of the
Radiant Sauna will be
accessed through the
control panel. There is a
control panel on the
interior and exterior of
the sauna, and both are
identical and perform the
same functions as well as
simultaneously display
the same information. You can operate the sauna
from either the interior or exterior control panels.
POWERING UP THE HEATERS
Press the POWER button and hold until the control
panel beeps, then release the button. The control
panel will now light up and the heaters are on.
Press the POWER button a second time for 5
seconds until the control panel beeps, and when you
release the button the control panel lights will turn
off . The heaters are now off. When the control
panel is lit up, the TEMP and TIME displays will
show the temperature and time settings last used in
the sauna.
SETTING THE TEMPERATURE
When heaters are on you can adjust the sauna
temperature. The temperature can be adjusted in
increments of 5F and can be set as high as 165F.
Press the TEMP+ or TEMP- to adjust the heater
temperature. The temperature will appear in the
display. After 5 seconds the display will reflect the
current sauna temperature. If the ambient
temperature in the outside room is under 65F, the
temperature display will read “LO” until the sauna
gets warm. It will display the actual temperature
once the sauna gets up to about 75F.
SETTING THE TIME
You can adjust the operating time of the heaters
from 5-60 minutes. The heaters will automatically
turn off after 60 minutes, at which time you can
turn them back on if you choose. Press the TIME+
or TIME- to change the time setting in increments
of 5 minutes. The system will beep 3 times when 5
minutes remain for the heater cycle.

LIGHT CONTROL
Press the LIGHT button to turn on both the interior light
and the therapy light. To operate just one of either the
interior light or therapy light, press the LIGHT button for 5
seconds until you see “2n” on the TIME display. While in
the “2n” mode, pressing the TIME+ button turns the interior
light on and off, and the TIME- turns the high intensity light
therapy fixture on and off. The exterior accent light
function operates along with the light therapy fixture. The
sauna will stay in the “2n” mode for 8 seconds before it will
transition back to the heat and temperature-setting mode.
To change colors for the therapy light, enter the “2n” mode
(press the LIGHT button for 5 seconds until you see “2n” in
the TIME display.) You will also see “L1” in the TEMP
display. You are now in the light therapy settings function
and it will remain in this function for 8 seconds before
reverting back to the normal heat and temperature-setting
mode. While in the “L1” function you can now push the
LIGHT button to change the colors to one of nine different
settings, L1-L9. A different color light is assigned to each
of the first 7 settings, and L8 will sequence through all the
light therapy colors rapidly, and L9 will sequence through
them slowly.
AUDIO CONTROL
Press the AUDIO button once so the indicator light is on.
By pushing the AUDIO button multiple times you will
sequence through Bluetooth (BLU), USB hookup (USB)
and FM radio (frequency station is displayed). Note: You
will not be able to sequence through to the next option until
the decibel (db) volume indicator appears in the display for
each setting.
BLUETOOTH
Push the AUDIO button until you get the BLU function in
the temperature display. Go to your personal device and
sync to the BTxxxx setting. Once your device says
“connected” you can play music through the sauna
sound system. When BLU is displayed on the control
panel you can control the volume through the
temperature display. Push the AUDIO button until you
are in BLU function and “Db” appears in the TIME
display. Press TIME+ or TIME- to adjust the volume. You
can sequence to the next or previous song on your playlist
by pressing TEMP+ or TEMP-. After 8 seconds the display
will revert to the sauna heater settings.
USB
Press the AUDIO button until you see USB function in the
temperature display. Plug in your device with a USB cable
to play music through the sauna sound system. When USB
is displayed on the control panel you can control the volume
through the Temperature display. Push the AUDIO button
until you are in the USB function and “Db” appears in the
time display. Press TIME+ or TIME- to adjust the volume.
Press TEMP+ or TEMP- to sequence to next or previous
song. After 8 seconds the displays will revert back to the
heater mode.
FM RADIO
Press the AUDIO button until you see radio station
frequency shown in the temperature display. Press TIME+
or TIME- to adjust the volume. Press TEMP+ or TEMP- to
change the radio frequency. You can also press the AUDIO
button for 5 seconds to search for the next available
frequency. After 8 seconds the displays will revert back to
the heater mode.
FAHRENHEIT VS CELSIUS
You can switch from Fahrenheit to Celsius by pressing
TEMP- and LOCK simultaneously for 5 seconds until you
hear two beeps. Repeat the process to revert to the previous
setting.
LOCK CONTROL
When the indicator light is on in any function you can press
the LOCK button for 5 seconds to keep the system in that
mode. Unlock by holding the LOCK button for 5 seconds.
OVERHEATING PROTECTION
If the sauna reaches a temperature of approximately
176F, the system will shut down and HH will show in
the digital display. The sauna will remain inoperable
until the temperature is down to 160F.