Almost Heaven Saunas Infralux Operating instructions

Infralux Sauna
Installation & Owner’s Manual
®
Thank you for the purchase of your beautiful Almost Heaven Infralux infrared sauna! Should you have
any questions about assembly or operation of this unit, please do not hesitate to call our support team at
888.355.3050, or email us at [e-mail].
This manual applies to all three sizes of the Infralux infrared sauna. The panels and bench sizes will be dierent,
but the assembly process is the same for all three units.
An Electrical Note - Your Infralux infrared sauna must run on a dedicated 20 amp circuit. No other electrical
device should be used on the sauna’s circuit.

Getting Started
To get started, remove the dust cover from the roof panel and nd the cardboard box which includes the door handle and assembly
hardware.
Note: You will have hardware left over after assembly - not all the provided hardware is used.
Step 1 - Inventory
Lay out all the sauna components. The kit includes the oor and roof panel, a back and door panel, and two side wall panels. It will
also come with the bench and bench support.
Step 2 - Placing the Floor Panel
Place the oor panel on a level surface. The oor heater should be positioned so that it sits at the front of the sauna.
Note: To avoid damaging the fully assembled sauna, it is recommended you install the sauna as close to the nal location as possible.
The sauna can be slid in place once fully assembled.
Step 3 - Placing the Back, Left, and Right Panels
Locate the back panel and center it atop the oor panel. While someone holds the backpanel upright, locate the left wall panel and
orient it so that the heater power cord is positioned upright, and the side window is at the front of the sauna. Line up the tongue
of the side wall panel so that it ts snugly into the groove of the back wall panel. After ensuring a snug t, secure the two panels
together with the brass clips. Repeat this process for the right side wall.
INFRALUX SAUNA INSTALLATION MANUAL - PAGE 1

Step 4 - Placing the Bench
Locate the bench support and position it in the notches on the left and right wall panels. You may have to bend the wall panels
out slightly to t the bench support in place - this is normal. Once the bench support is in place, connect the bench support power
cord to the outlet on the left wall panel, and connect the oor heating panel power cord to the outlet on the right wall panel.
Place the bench on top of the bench support and push it back so that it rests comfortably over top the back wall bench support.
Secure the bench to the bench support and back wall supports using the four 2”screws in the pre-drilled holes.
Step 5 - Placing the Door Panel
It is imperative that you use two people to install the door panel! Locate the door panel and orient it so the key hole in the mount-
ing bracket is positioned at the bottom. Lift the panel up and rest it on the brass notches on the wall panels. Once the notches are
nested into the key holes, rmly pull the door panel down to lock the t. You may need to use a rubber mallet to make the top of
the door panel ush with the wall panels.
Helpful Hint: If one of the notches is not nesting in its corresponding key hole, use a crowbar to gently lift the door panel up to
ne-tune the alignment.
INFRALUX SAUNA INSTALLATION MANUAL - PAGE 2

Step 6 - Securing the Door Handle
The door handle mounts to the glass door with the provided hardware according to the image below. Secure the exterior handle
rst, with the mounting screw protruding into the inside of the sauna. Secure the interior door handle to the mounting screw us-
ing the Alan screws.
Step 7 - Securing the Roof Panel
Loosely the roof panel on top of the sauna. Push the wall panel power and data cords through the corresponding holes in the roof
panel. Once all the power and data cords are through the roof panel, rmly pull it down so that it sits snug and level atop the sauna.
Secure the roof panel to the wall panels using the provided 2” screws through the pre-drilled holes in the frame of the roof panel.
Step 8 - Connecting the Power Cords and Data Cables
Connect the plugs for the heater panels to their cooresponding outlets on top of the sauna. Also, connect the data cables to their
corresponding connections. (Images 26 & 27)
Operating Your Sauna
It is imperative that your infrared sauna run on a dedicated 20 amp circuit. No other elec-
trically powered device should be used on the sauna’s circuit. Please note the plug that
comes with your sauna - you should have a corresponding outlet for the sauna. If you do
not already have this conguration on the outlet for your sauna, it is a simple swap out for
any licensed electrician.
®
INFRALUX SAUNA INSTALLATION MANUAL - PAGE 3