Almost Heaven Saunas Bluestone Operating instructions

In addition to reading this manual through to the end before proceeding with assembly
you may nd our instruction video helpful.
You can nd it at: youtube.com/user/almostheavensauna
Bluestone Sauna
Installation & Owner’s Manual
®

Read this entire manual through to the end before proceeding with the assembly.
BLUESTONE SAUNA INSTALLATION MANUAL
page 1
®
Thank you for your purchase of your Bluestone sauna! Should you have any questions during assembly, please
feel free to call us at 888.355.3050, or email [e-mail]. Regular business hours are 9-5 EST, M-F.
Your Bluestone Indoor Sauna is specically designed to utilize your existing oor. As such, assembly is made very
simple since the entire sauna sits on pre-fabricated rails and risers. Your sauna can be assembled on any surface
that is rm and at, including concrete, ceramic, vinyl, laminate or tile. (Installation on a carpeted surface is not
recommended.)
Your Bluestone kit should include the following:
c 4 oor risers
c 4 Wall Support Rails
c 4 Roof Support Rails
c 2 Roof Panels
c 2 Pieces of Roof Trim
c Wall Panel A
c Wall Panel B
c Wall Panel C
c Wall Panel D
c Wall Panel E
c Window Panel F
c Door Panel G
c Window Panel H
c Window Panel I
c Upper Long Bench
c Lower Side Bench
c Long Backrest w/LED light
c Short Backrest
c LED Power Supply
c Door handle Assembly
c Bucket and Ladle
c Heater
c Stones
c Thermometer/Hydrometer
c Wall Sensor Cover
c Hardware Bag containing 2” screws, 2.5”Bench Screws, and Trim nails
c Heater Fence Kit
These tools are required to assemble yourBluestone sauna:
c Cordless drill
c Tape measurer
c Rubber mallet
c Hammer
c 1/2” or 5/8” Forstner Bit
c Utility Knife
c Screwdriver (Phillips and Flathead)
c Level
c Step stool or ladder

BLUESTONE SAUNA INSTALLATION MANUAL
page 2
Step 1. Connect the 4 Floor Risers
Fasten the 4 oor risers together using the pre-drilled holes as a guide. (1-4)
Step 2. Position Wall Support Rails
Align each wall support so that the angled cuts make a corner (5). Each wall support has a predrilled hole. Fasten the
front, back, and sides together (6 & 7) and lay the assembly squarely on top of the oor risers with the groove facing
up (8). The rails should overlap both sides of the riser by approximately 1” (9). Secure the assembly to the oor risers
using 3 screws evenly spaced on each wall support rail (10 & 11).
Step 3. Position wall panels A & B
Position wall panel A in the groove of the left rail and push it ush against the back rail. Having a helper hold wall
panel A, orient wall panel B so that the vent holes are on top and place it in the groove of the back rail (12). Push
the at edge against wall panel A. Align the 2 panels so they are ush and fasten them together using the 2” screws
through the predrilled holes (13 & 14).
Image 1 Image 2 Image 3 Image 4
Image 5 Image 6 Image 7 Image 8
Image 9 Image 10 Image 11
Image 12 Image 13 Image 14

BLUESTONE SAUNA INSTALLATION MANUAL
page 3
Step 4. Position Wall Panels C & D
Position wall panel C into the groove of the back rail. Attach it to wall panel B by way of the tongue and groove t (15
& 16). Secure it by tapping it into place with a rubber mallet. Position wall panel D into the groove to the right-side rail
and push ush against the back rail (17). Being sure panels D & C are ush with each other, fasten them together using
the 2” screws (18).
Step 5. Finish Wall Panels
Position wall panel E into the groove of the right-side rail. Slide wall panel E into place with wall panel D (19). Panel
E connects to panel D via tongue and groove so there is no need to use screws. Use a rubber mallet to secure the t.
Place window panel F in the groove on the front rail (20) and push the at end against wall panel E. Being sure the two
panels are ush, fasten them together using 2”screws through the pre-drilled holes on panel E (21).
Now place door panel G onto the front rail, being sure to snip the twine holding the door to the frame (22). Push the
door panel into window panel F to secure the tongue and groove t. Now place window panel H on the front rail and
push into door panel G (23). Finally, place window panel I on the left-side rail and push into wall panel A (24). Panels
I and A connect via tongue and groove t. Now, being sure window panels I and H are ush with each other, secure
them together using 2” screws through the pre-drilled holes on window panel I (25).
Image 15 Image 16 Image 17 Image 18
Image 19 Image 20 Image 21
Image 22 Image 23 Image 24 Image 25

BLUESTONE SAUNA INSTALLATION MANUAL
page 4
Step 6. Assemble and Position Roof Support Rails
Align each roof support rail so the angled cuts join together to make a 90-degree angle placing the longer supports
on the sides and the shorter supports on the front and back. Fasten them together using 2”screws through the pre-
drilled holes (26, 27 & 28). This is the same assembly you performed in Step 2.
Place the assembly on top of the wall panels so that the wall panels t snugly into the groove. When in place, secure
the assembly to the walls using three 2”screws on each rail (29 & 30).
Step 7. Bench and LED Backrest Installation
Note: You may choose to install all the benches and backrests after the sauna is completed, but you may nd it easier
to install with the extra space and light aorded at this step.
Place the upper bench on the pre-installed upper bench supports and push ush against the back wall, being sure the
side of the bench with the screws showing is oriented towards the back (31). Secure the bench to the back and side
panels using 2.5” bench screws and the pre-drilled holes in the bench frame supports (32).
Repeat this process for the lower side bench (33), securing it to the panel A and B.
Image 26 Image 27 Image 28
Image 29 Image 30
Image 31 Image 32
Image 33

BLUESTONE SAUNA INSTALLATION MANUAL
page 5
Step 7. Bench and LED Backrest Installation continued . . .
Center the LED Backrest between the two sides being sure it’s oriented so the shorter slat is down and position
it vertically at a height most comfortable for you (typically 8-12” from the bench). Using a level to ensure proper
installation, fasten the backrest into place using the 2”screws (34 & 35). Repeat this process for the lower side bench
backrest (36).
To connect the LED light to the power source, bore a 5/8”hole through the back of the panel at the bottom right
corner of the backrest and push the LED pigtail through (37 & 38). Now mount the power supply to the back of the
sauna at the base of panel C, underneath the hole you just bored (39). Connect the power supply and LED pigtail (40),
and plug in the supply to an outlet. You are able to turn on the LED light and adjust its brightness from within the
sauna using the control mounted to the side of the backrest (41).
Image 34 Image 35 Image 36
Image 37 Image 38 Image 39 Image 40
Image 41

BLUESTONE SAUNA INSTALLATION MANUAL
page 6
Step 8. Position Roof Panels
Position the two roof panels on top of the roof support rails with the pre-drilled holes facing up (42 & 43). The roof
panels connect via tongue and groove t. Align the connected roof panels on the rails so that approximately 1” of
the support rails extend past each side of the roof panels (44). Once evenly spaced, secure the panels with 2” screws
through the predrilled holes (45). Install the provided trim pieces with the 1” trim nails to cover the raw edges of the
roof panels (46).
Step 9. Accessories
1. Install the vent hole cover using the provided screw and washer (47 & 48)
2. Hang the thermometer/hydrometer on the opposite wall of the heater 12-15 inches below the ceiling (49)
3. Unwrap bucket and ladle and set in sauna (50).
4. Install doorknob (51-52)
5.
6.
7.
8.
9.
10.
11.
12.
Image 42 Image 43 Image 44
Image 45 Image 46
Image 47 Image 48 Image 49
Image 50 Image 51 Image 52

BLUESTONE SAUNA INSTALLATION MANUAL
page 7
After the sauna has been installed, sweep down the inside to remove any sawdust and wood shavings, and
then vacuum completely. Using a damp cloth with warm water, wipe down the entire sauna including the
benches to remove any remaining dirt, dust and debris.
Step 11. Heater Installation
Please consult your heater manual for all heater installation information. All electrical connections must be
done by a qualied licensed electrician.
TRADITIONAL SAUNA USE
Congratulations! You are ready to enjoy your sauna! You may use your sauna in a wet or dry fashion. A dry sauna
means you do not sprinkle any water onto the stones, while wet means you increase the humidity of the room by
sprinkling water on the stones. Please note that not much water is needed to achieve a wet sauna experience!
The sauna as we know it originates in Finland. The typical sauna experience follows the steps below, but you may
enjoy your sauna in any way that you like!
• Set your heater so your sauna achieves the desired temperature. This is typically 160 - 185+ degrees F. Please
note, novice sauna users should begin at the lower end of that range and increase their high temperature over
time.
• Take a quick shower or a quick dip in a hot tub or pool.
• Step into the sauna and enjoy for 5-15 minutes, bringing a towel to sit or lay on. Leave the sauna once you are
perspiring freely.
• Take a plunge in a pool, shower, snowbank, lake – anything that will relax and cool you down for 10 – 20
minutes.
• Step into the sauna again. During this visit, you may wish to sprinkle small amounts of water onto the stones
to create bursts of steam. If water spills through the heater to the oor, you are using too much water, though
this will not hurt the heater or the sauna.
• Continue repeating this process. After your nal visit to your sauna, relax for 20 minutes. Shower with warm
water initially, nishing with cool water to close your skin pores.
• Prepare to feel refreshed for the day or to have an amazing night’s sleep!
Whatever your sauna routine, it is imperative that you STAY HYDRATED!