ALOGO MOVE PRO User manual

The most accurate
technology ever implemented
in an equine sensor.
SYNCHRONISATIONADDITIONAL
INFORMATION
QUICK START
3.
In order to view them, please open
the “Alogo” application so that your
sessions are synchronized with your
smartphone and sent to our Cloud.
Your phone needs to have an active
internet connection.
Wifi / 3G
1. Training
Once your session(s) are over, the recordings
are stored in the memory of your Move sensor.
4. Data saved
on the cloud
2. Sensor
Splash, shock and
dust resistant.
Your Alogo Move Pro sensor has a built-in GPS chip. The accuracy of the
GPS depends on several environmental factors such as weather, location
and whether you are indoors or outdoors. If GPS reception is poor, for
example in an indoor arena, some data will not be displayed. For more
information, please refer to the instruction manual.
Safety instructions:
Do not expose your Alogo Move sensor to any violent impacts, such as
dropping or throwing the device. Do not place magnetized objects near the
Alogo Move sensor for long periods of time, as this may cause irreversible
damage to the sensor.
After use, store the product in a dry place. Never attempt to disassemble
or reassemble your product yourself. All repairs must be carried out by a
representative certified by Alogo Analysis SA.
We recommend that you use your Alogo Move sensor in a temperature
range between -20°C and +50°C (-4°F and 122°F). Prolonged use outside
of this temperature range may cause irreversible damage to components,
especially the battery, and provide inaccurate data.
The sensor is equipped with an internal lithium polymer battery (3V,
3000mAh). If used improperly, the internal battery may explode or
release dangerous chemicals. Never disassemble, crush or puncture
the battery. Do not dispose of it in fire or water.
Communication is wireless via Bluetooth Low Energy 4.2+, 2.4Ghz Pro-
tocol. The transmission speed and range of the sensor with your smart-
phone depends on the distance between them and any other obstacles in
between, such as the horse, a person or a wall.
•We recommend to switch on your sensor before the riding session
and to begin recording it when you start to work the horse.
• The recording length of a session will have an impact on the Bluetooth
transfer time.
Alogo Analysis SA
Switzerland
www.alogo.io
•In order to obtain the most accurate data, don’t place any metallic or
magnetic accessories around the sensor when in use.
• Do not immerse the sensor in water or any other liquid.
Cloud
Alogo
5. Display on a
Smartphone / PC / Tablette
Indicator:
Blinking Yellow LED
RECOMMENDATIONS
version 1
SWISS TECHNOLOGY
TM

GUIDE
Front
Back
INSTALLATION
USE
CAUTION
Before starting to use your Move sensor, please read the complete
instructions manual carefully, especially the safety instructions on
our website: www.alogo.io/docs.
Before using for the first time, please charge your Move sensor
for 3.5 hours with the supplied USB cable.
To start recording a session.
Without smartphone
1. Turning ON: Press the power button for 1.5 seconds until the red LED
lights up. You can start recording when you see the pink LED.
2. Recording: Press the power button once. The LED turns green
and blinking, indicates the start of the recording.
3. Stop: You can stop the recording by pressing once the
power button of your Move sensor.
4. Turning OFF:The sensor automatically turns o after 2 minutes
if no movement is detected. You can switch it o by pressing
the power button for 1.5 seconds until the red LED lights up.
To start recording a session.
With smartphone
Please note:Bluetooth must be active on your smartphone.
1. Turning ON:
Press the power button for 1.5 seconds until the red LED lights up.
2. Launch the “Alogo” app:
Or download it from the AppStore or Google Play.
• Create an account if you haven’t already done so or log in
with your credentials.
• Settings tab
Press “Sensor management” and select your Move sensor.
The LED will blink blue once the connection is established.
The next time the phone is used, it will automatically
connect to the sensor that was last selected.
3. Recording:
Press the “Recording” button in the interface.
4. Stop:
Press the “Stop” button in the interface. You can also stop the
session by directly pressing the power button on your Move sensor.
5. Turning OFF:
The sensor automatically turns o after 2 minutes if no movement
is detected. You can switch it o by pressing the button for 1.5 seconds
until a red LED lights up.
To turn it o from the app, go to Settings > Sensor management
> Select your sensor > Turn o.
Included in the Box
Sensor: Alogo Move Pro.
USB cable: To charge your sensor.
Hook: To attach your martingale or your training aids to your girth.
Measuring tape : To measure the distance between the sensor and the
ground the first time the sensor is used on a new horse.
(More info in the complete manual).
Quick Start guide.
Sensor holder supplied separately.
1. Fasten to the girth
Positioning of the sensor
(make sure that the sensor is
facing in the right direction)
Ground :
Face toward the ground
Horse :
Face against the horse
LED, Button and USB :
View on the left side of the horse
2. The sensor must be placed underneath the horse at the center,
and facing in the correct direction.
Attention: Any adjustments to the girth should be done equally on
both sides so that the sensor remains in a central position.
USE PICTOGRAM
LED
POWER BUTTON
Start or stop recording
For charging
GROUND
HORSE
Red LED Blinks for a few seconds when switching ON or OFF.
If it remains constantly lit, the memory is full.
Pink LED Blinks while searching for a GPS satellite
connection. Constantly lit means that the GPS
is connected.
Green LED Blinking: recording a current session.
Blue LED Fast blinking: Bluetooth sensor connection
available.
Steady blinking: Sensor connected via Bluetooth.
LED Blue Blinking alternately: The Bluetooth connection has
and Red been lost. It continues for 30 seconds.
Yellow LED Blinking: The Move sensor is in sync with the
smartphone.
When the sensor is connected to a power source, the LED displays the charging
status in green. If the battery level is low, the blinking will become slower.
The LED will turn OFF when the battery of your sensor is fully charged.
Sensor holder
Sensor
centered
Front Back
Reset
Disconnection during recording
Your Move sensor works independently from the mobile app.
In case you lose your Bluetooth connection, your session continues to be
recorded on the internal memory of your sensor.
GROUND

GUIDE
Front
Back
INSTALLATION
USE
CAUTION
Before starting to use your Move sensor, please read the complete
instructions manual carefully, especially the safety instructions on
our website: www.alogo.io/docs.
Before using for the first time, please charge your Move sensor
for 3.5 hours with the supplied USB cable.
To start recording a session.
Without smartphone
1. Turning ON: Press the power button for 1.5 seconds until the red LED
lights up. You can start recording when you see the pink LED.
2. Recording: Press the power button once. The LED turns green
and blinking, indicates the start of the recording.
3. Stop: You can stop the recording by pressing once the
power button of your Move sensor.
4. Turning OFF:The sensor automatically turns o after 2 minutes
if no movement is detected. You can switch it o by pressing
the power button for 1.5 seconds until the red LED lights up.
To start recording a session.
With smartphone
Please note:Bluetooth must be active on your smartphone.
1. Turning ON:
Press the power button for 1.5 seconds until the red LED lights up.
2. Launch the “Alogo” app:
Or download it from the AppStore or Google Play.
• Create an account if you haven’t already done so or log in
with your credentials.
• Settings tab
Press “Sensor management” and select your Move sensor.
The LED will blink blue once the connection is established.
The next time the phone is used, it will automatically
connect to the sensor that was last selected.
3. Recording:
Press the “Recording” button in the interface.
4. Stop:
Press the “Stop” button in the interface. You can also stop the
session by directly pressing the power button on your Move sensor.
5. Turning OFF:
The sensor automatically turns o after 2 minutes if no movement
is detected. You can switch it o by pressing the button for 1.5 seconds
until a red LED lights up.
To turn it o from the app, go to Settings > Sensor management
> Select your sensor > Turn o.
Included in the Box
Sensor: Alogo Move Pro.
USB cable: To charge your sensor.
Hook: To attach your martingale or your training aids to your girth.
Measuring tape : To measure the distance between the sensor and the
ground the first time the sensor is used on a new horse.
(More info in the complete manual).
Quick Start guide.
Sensor holder supplied separately.
1. Fasten to the girth
Positioning of the sensor
(make sure that the sensor is
facing in the right direction)
Ground :
Face toward the ground
Horse :
Face against the horse
LED, Button and USB :
View on the left side of the horse
2. The sensor must be placed underneath the horse at the center,
and facing in the correct direction.
Attention: Any adjustments to the girth should be done equally on
both sides so that the sensor remains in a central position.
USE PICTOGRAM
LED
POWER BUTTON
Start or stop recording
For charging
GROUND
HORSE
Red LED Blinks for a few seconds when switching ON or OFF.
If it remains constantly lit, the memory is full.
Pink LED Blinks while searching for a GPS satellite
connection. Constantly lit means that the GPS
is connected.
Green LED Blinking: recording a current session.
Blue LED Fast blinking: Bluetooth sensor connection
available.
Steady blinking: Sensor connected via Bluetooth.
LED Blue Blinking alternately: The Bluetooth connection has
and Red been lost. It continues for 30 seconds.
Yellow LED Blinking: The Move sensor is in sync with the
smartphone.
When the sensor is connected to a power source, the LED displays the charging
status in green. If the battery level is low, the blinking will become slower.
The LED will turn OFF when the battery of your sensor is fully charged.
Sensor holder
Sensor
centered
Front Back
Reset
Disconnection during recording
Your Move sensor works independently from the mobile app.
In case you lose your Bluetooth connection, your session continues to be
recorded on the internal memory of your sensor.
GROUND

GUIDE
Front
Back
INSTALLATION
USE
CAUTION
Before starting to use your Move sensor, please read the complete
instructions manual carefully, especially the safety instructions on
our website: www.alogo.io/docs.
Before using for the first time, please charge your Move sensor
for 3.5 hours with the supplied USB cable.
To start recording a session.
Without smartphone
1. Turning ON: Press the power button for 1.5 seconds until the red LED
lights up. You can start recording when you see the pink LED.
2. Recording: Press the power button once. The LED turns green
and blinking, indicates the start of the recording.
3. Stop: You can stop the recording by pressing once the
power button of your Move sensor.
4. Turning OFF:The sensor automatically turns o after 2 minutes
if no movement is detected. You can switch it o by pressing
the power button for 1.5 seconds until the red LED lights up.
To start recording a session.
With smartphone
Please note:Bluetooth must be active on your smartphone.
1. Turning ON:
Press the power button for 1.5 seconds until the red LED lights up.
2. Launch the “Alogo” app:
Or download it from the AppStore or Google Play.
• Create an account if you haven’t already done so or log in
with your credentials.
• Settings tab
Press “Sensor management” and select your Move sensor.
The LED will blink blue once the connection is established.
The next time the phone is used, it will automatically
connect to the sensor that was last selected.
3. Recording:
Press the “Recording” button in the interface.
4. Stop:
Press the “Stop” button in the interface. You can also stop the
session by directly pressing the power button on your Move sensor.
5. Turning OFF:
The sensor automatically turns o after 2 minutes if no movement
is detected. You can switch it o by pressing the button for 1.5 seconds
until a red LED lights up.
To turn it o from the app, go to Settings > Sensor management
> Select your sensor > Turn o.
Included in the Box
Sensor: Alogo Move Pro.
USB cable: To charge your sensor.
Hook: To attach your martingale or your training aids to your girth.
Measuring tape : To measure the distance between the sensor and the
ground the first time the sensor is used on a new horse.
(More info in the complete manual).
Quick Start guide.
Sensor holder supplied separately.
1. Fasten to the girth
Positioning of the sensor
(make sure that the sensor is
facing in the right direction)
Ground :
Face toward the ground
Horse :
Face against the horse
LED, Button and USB :
View on the left side of the horse
2. The sensor must be placed underneath the horse at the center,
and facing in the correct direction.
Attention: Any adjustments to the girth should be done equally on
both sides so that the sensor remains in a central position.
USE PICTOGRAM
LED
POWER BUTTON
Start or stop recording
For charging
GROUND
HORSE
Red LED Blinks for a few seconds when switching ON or OFF.
If it remains constantly lit, the memory is full.
Pink LED Blinks while searching for a GPS satellite
connection. Constantly lit means that the GPS
is connected.
Green LED Blinking: recording a current session.
Blue LED Fast blinking: Bluetooth sensor connection
available.
Steady blinking: Sensor connected via Bluetooth.
LED Blue Blinking alternately: The Bluetooth connection has
and Red been lost. It continues for 30 seconds.
Yellow LED Blinking: The Move sensor is in sync with the
smartphone.
When the sensor is connected to a power source, the LED displays the charging
status in green. If the battery level is low, the blinking will become slower.
The LED will turn OFF when the battery of your sensor is fully charged.
Sensor holder
Sensor
centered
Front Back
Reset
Disconnection during recording
Your Move sensor works independently from the mobile app.
In case you lose your Bluetooth connection, your session continues to be
recorded on the internal memory of your sensor.
GROUND

GUIDE
Front
Back
INSTALLATION
USE
CAUTION
Before starting to use your Move sensor, please read the complete
instructions manual carefully, especially the safety instructions on
our website: www.alogo.io/docs.
Before using for the first time, please charge your Move sensor
for 3.5 hours with the supplied USB cable.
To start recording a session.
Without smartphone
1. Turning ON: Press the power button for 1.5 seconds until the red LED
lights up. You can start recording when you see the pink LED.
2. Recording: Press the power button once. The LED turns green
and blinking, indicates the start of the recording.
3. Stop: You can stop the recording by pressing once the
power button of your Move sensor.
4. Turning OFF:The sensor automatically turns o after 2 minutes
if no movement is detected. You can switch it o by pressing
the power button for 1.5 seconds until the red LED lights up.
To start recording a session.
With smartphone
Please note:Bluetooth must be active on your smartphone.
1. Turning ON:
Press the power button for 1.5 seconds until the red LED lights up.
2. Launch the “Alogo” app:
Or download it from the AppStore or Google Play.
• Create an account if you haven’t already done so or log in
with your credentials.
• Settings tab
Press “Sensor management” and select your Move sensor.
The LED will blink blue once the connection is established.
The next time the phone is used, it will automatically
connect to the sensor that was last selected.
3. Recording:
Press the “Recording” button in the interface.
4. Stop:
Press the “Stop” button in the interface. You can also stop the
session by directly pressing the power button on your Move sensor.
5. Turning OFF:
The sensor automatically turns o after 2 minutes if no movement
is detected. You can switch it o by pressing the button for 1.5 seconds
until a red LED lights up.
To turn it o from the app, go to Settings > Sensor management
> Select your sensor > Turn o.
Included in the Box
Sensor: Alogo Move Pro.
USB cable: To charge your sensor.
Hook: To attach your martingale or your training aids to your girth.
Measuring tape : To measure the distance between the sensor and the
ground the first time the sensor is used on a new horse.
(More info in the complete manual).
Quick Start guide.
Sensor holder supplied separately.
1. Fasten to the girth
Positioning of the sensor
(make sure that the sensor is
facing in the right direction)
Ground :
Face toward the ground
Horse :
Face against the horse
LED, Button and USB :
View on the left side of the horse
2. The sensor must be placed underneath the horse at the center,
and facing in the correct direction.
Attention: Any adjustments to the girth should be done equally on
both sides so that the sensor remains in a central position.
USE PICTOGRAM
LED
POWER BUTTON
Start or stop recording
For charging
GROUND
HORSE
Red LED Blinks for a few seconds when switching ON or OFF.
If it remains constantly lit, the memory is full.
Pink LED Blinks while searching for a GPS satellite
connection. Constantly lit means that the GPS
is connected.
Green LED Blinking: recording a current session.
Blue LED Fast blinking: Bluetooth sensor connection
available.
Steady blinking: Sensor connected via Bluetooth.
LED Blue Blinking alternately: The Bluetooth connection has
and Red been lost. It continues for 30 seconds.
Yellow LED Blinking: The Move sensor is in sync with the
smartphone.
When the sensor is connected to a power source, the LED displays the charging
status in green. If the battery level is low, the blinking will become slower.
The LED will turn OFF when the battery of your sensor is fully charged.
Sensor holder
Sensor
centered
Front Back
Reset
Disconnection during recording
Your Move sensor works independently from the mobile app.
In case you lose your Bluetooth connection, your session continues to be
recorded on the internal memory of your sensor.
GROUND

The most accurate
technology ever implemented
in an equine sensor.
SYNCHRONISATIONADDITIONAL
INFORMATION
QUICK START
3.
In order to view them, please open
the “Alogo” application so that your
sessions are synchronized with your
smartphone and sent to our Cloud.
Your phone needs to have an active
internet connection.
Wifi / 3G
1. Training
Once your session(s) are over, the recordings
are stored in the memory of your Move sensor.
4. Data saved
on the cloud
2. Sensor
Splash, shock and
dust resistant.
Your Alogo Move Pro sensor has a built-in GPS chip. The accuracy of the
GPS depends on several environmental factors such as weather, location
and whether you are indoors or outdoors. If GPS reception is poor, for
example in an indoor arena, some data will not be displayed. For more
information, please refer to the instruction manual.
Safety instructions:
Do not expose your Alogo Move sensor to any violent impacts, such as
dropping or throwing the device. Do not place magnetized objects near the
Alogo Move sensor for long periods of time, as this may cause irreversible
damage to the sensor.
After use, store the product in a dry place. Never attempt to disassemble
or reassemble your product yourself. All repairs must be carried out by a
representative certified by Alogo Analysis SA.
We recommend that you use your Alogo Move sensor in a temperature
range between -20°C and +50°C (-4°F and 122°F). Prolonged use outside
of this temperature range may cause irreversible damage to components,
especially the battery, and provide inaccurate data.
The sensor is equipped with an internal lithium polymer battery (3V,
3000mAh). If used improperly, the internal battery may explode or
release dangerous chemicals. Never disassemble, crush or puncture
the battery. Do not dispose of it in fire or water.
Communication is wireless via Bluetooth Low Energy 4.2+, 2.4Ghz Pro-
tocol. The transmission speed and range of the sensor with your smart-
phone depends on the distance between them and any other obstacles in
between, such as the horse, a person or a wall.
•We recommend to switch on your sensor before the riding session
and to begin recording it when you start to work the horse.
• The recording length of a session will have an impact on the Bluetooth
transfer time.
Alogo Analysis SA
Switzerland
www.alogo.io
•In order to obtain the most accurate data, don’t place any metallic or
magnetic accessories around the sensor when in use.
• Do not immerse the sensor in water or any other liquid.
Cloud
Alogo
5. Display on a
Smartphone / PC / Tablette
Indicator:
Blinking Yellow LED
RECOMMENDATIONS
version 1
SWISS TECHNOLOGY
TM

The most accurate
technology ever implemented
in an equine sensor.
SYNCHRONISATIONADDITIONAL
INFORMATION
QUICK START
3.
In order to view them, please open
the “Alogo” application so that your
sessions are synchronized with your
smartphone and sent to our Cloud.
Your phone needs to have an active
internet connection.
Wifi / 3G
1. Training
Once your session(s) are over, the recordings
are stored in the memory of your Move sensor.
4. Data saved
on the cloud
2. Sensor
Splash, shock and
dust resistant.
Your Alogo Move Pro sensor has a built-in GPS chip. The accuracy of the
GPS depends on several environmental factors such as weather, location
and whether you are indoors or outdoors. If GPS reception is poor, for
example in an indoor arena, some data will not be displayed. For more
information, please refer to the instruction manual.
Safety instructions:
Do not expose your Alogo Move sensor to any violent impacts, such as
dropping or throwing the device. Do not place magnetized objects near the
Alogo Move sensor for long periods of time, as this may cause irreversible
damage to the sensor.
After use, store the product in a dry place. Never attempt to disassemble
or reassemble your product yourself. All repairs must be carried out by a
representative certified by Alogo Analysis SA.
We recommend that you use your Alogo Move sensor in a temperature
range between -20°C and +50°C (-4°F and 122°F). Prolonged use outside
of this temperature range may cause irreversible damage to components,
especially the battery, and provide inaccurate data.
The sensor is equipped with an internal lithium polymer battery (3V,
3000mAh). If used improperly, the internal battery may explode or
release dangerous chemicals. Never disassemble, crush or puncture
the battery. Do not dispose of it in fire or water.
Communication is wireless via Bluetooth Low Energy 4.2+, 2.4Ghz Pro-
tocol. The transmission speed and range of the sensor with your smart-
phone depends on the distance between them and any other obstacles in
between, such as the horse, a person or a wall.
•We recommend to switch on your sensor before the riding session
and to begin recording it when you start to work the horse.
• The recording length of a session will have an impact on the Bluetooth
transfer time.
Alogo Analysis SA
Switzerland
www.alogo.io
•In order to obtain the most accurate data, don’t place any metallic or
magnetic accessories around the sensor when in use.
• Do not immerse the sensor in water or any other liquid.
Cloud
Alogo
5. Display on a
Smartphone / PC / Tablette
Indicator:
Blinking Yellow LED
RECOMMENDATIONS
version 1
SWISS TECHNOLOGY
TM

The most accurate
technology ever implemented
in an equine sensor.
SYNCHRONISATIONADDITIONAL
INFORMATION
QUICK START
3.
In order to view them, please open
the “Alogo” application so that your
sessions are synchronized with your
smartphone and sent to our Cloud.
Your phone needs to have an active
internet connection.
Wifi / 3G
1. Training
Once your session(s) are over, the recordings
are stored in the memory of your Move sensor.
4. Data saved
on the cloud
2. Sensor
Splash, shock and
dust resistant.
Your Alogo Move Pro sensor has a built-in GPS chip. The accuracy of the
GPS depends on several environmental factors such as weather, location
and whether you are indoors or outdoors. If GPS reception is poor, for
example in an indoor arena, some data will not be displayed. For more
information, please refer to the instruction manual.
Safety instructions:
Do not expose your Alogo Move sensor to any violent impacts, such as
dropping or throwing the device. Do not place magnetized objects near the
Alogo Move sensor for long periods of time, as this may cause irreversible
damage to the sensor.
After use, store the product in a dry place. Never attempt to disassemble
or reassemble your product yourself. All repairs must be carried out by a
representative certified by Alogo Analysis SA.
We recommend that you use your Alogo Move sensor in a temperature
range between -20°C and +50°C (-4°F and 122°F). Prolonged use outside
of this temperature range may cause irreversible damage to components,
especially the battery, and provide inaccurate data.
The sensor is equipped with an internal lithium polymer battery (3V,
3000mAh). If used improperly, the internal battery may explode or
release dangerous chemicals. Never disassemble, crush or puncture
the battery. Do not dispose of it in fire or water.
Communication is wireless via Bluetooth Low Energy 4.2+, 2.4Ghz Pro-
tocol. The transmission speed and range of the sensor with your smart-
phone depends on the distance between them and any other obstacles in
between, such as the horse, a person or a wall.
•We recommend to switch on your sensor before the riding session
and to begin recording it when you start to work the horse.
• The recording length of a session will have an impact on the Bluetooth
transfer time.
Alogo Analysis SA
Switzerland
www.alogo.io
•In order to obtain the most accurate data, don’t place any metallic or
magnetic accessories around the sensor when in use.
• Do not immerse the sensor in water or any other liquid.
Cloud
Alogo
5. Display on a
Smartphone / PC / Tablette
Indicator:
Blinking Yellow LED
RECOMMENDATIONS
version 1
SWISS TECHNOLOGY
TM