Alphamount APPSLTK1 User manual
Model: APPSLTK1
Large Tilting TV Wall Mount
Instruction Manual V2.0
Thank you for choosing this Alphamount product! At Alphamount we strive
to provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact us at
1
IMPORTANT SAFETY INFORMATION
Check the VESA Pattern of TV before the Installation
Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete block
and brick walls. -
DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.
600 mm ≈ 23 5/8 in.
400 mm ≈ 15 3/4 in.
Minimum VESA pattern: 200mm/8 in.(W)x100mm/4 in.(H)
If your TV VESA is greater than 600x400 mm/24x16in. or less than
VESA 200x100mm/8x4 in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
MAX: 600mm/23.6 in.
MAX: 400mm/16 in.
Weight Restrictions
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only
within the maximum weights indicated. Use with
products heavier than the maximum weights
indicated may result in failure of the mount and
its accessories, causing damage and or injury.
If your TV weighs more, this
mount is NOT compatible.
132lbs/
60kg
WARNING
2
Verify Your Wall Construction
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
If you are not sure the
wall construction, please
contact our customer
service at
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, please contact our
• Please note: Not all hardware included in this package will be used.
Left TV Bracket x1
03
Right TV Bracket x1
04
Stud Finder Tape Measure Pencil Drill
7/32in. (5.5mm)
Wood Drill
3/8 in. (10mm)
Concrete Drill
1/2in. (13mm)
Socket Wrench
Philips
Screwdriver
Hammer 5/16 in. (8mm)
Wrench
Awl
Washer with
3 holes x4
I
Spacer
L10mm
Spacer
L2.5mm
Spacer
L22mm
x4
L
x4
K
x8
J
Note: The spacers are
shown in accordance
with the actual size
x4 Wall
Anchor
Lag Screw
ST8x65 mm
x4
3
Right Wall Plate x1
01
Left Wall Plate x1
02
Note: The lag screw is shown in accordance with the actual size
These anchors are for
concrete or brick walls
ONLY. DO NOT use them in
drywall or wood studs.
CAUTION!
Supplied Parts and Hardware for Step 2 and 3
G
O
x4
A
x4
B
x4
C
x4
D
x4
F
Washer
M8
x4
H
M4x30mm
Bolt
M6x15mm
Bolt
M6x35mm
Bolt
M8x15mm
Bolt
x4
E
M8x35mm
Bolt
M8x50mm
Bolt
Note: The bolts are shown in accordance with the actual size
Level
04
03
I
A/B/D
J/K
(If needed)
Only one bolt size fits your TV.
4
Step 1 Secure the TV Brackets to TV
Select TV Bolts
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Note: If necessary, the spacers can be used in multi-layer. If the installation
fails after trying various methods, please contact customer service at
Too Long
Correct Correct
Too Short
CAUTION: Ensure the TV brackets
[03 and 04] are EQUALLY CENTERED
on your TV AND securely fastened in
place.
Option A (For Flat Back TV)
04 03
Alternate
Spacer
Setups
M4 M6 M8
04
03
04
03
I
A/C/E/F
J/K/L
03
A/B/D
I
J/K
(If needed)
03
I
A/C/E/F
J/K/L
Option D
5
04
A/ C/ E/ F
J/ K/ L
I
Option B (For Round Back TV)
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
04
For cable interference or inset holes, use spacers [ J ], [ K ] and [ L ] to create
extra space between the TV and TV brackets
Alternate
Spacer
Setups
Alternate
Spacer
Setups
Alternate
Spacer
Setups
Alternate
Spacer
Setups
6
Step 2 Assemble the Wall Plate
Step 3 Attach Wall Plate to Wall
For wood stud installation, follow STEP 3A
For concrete installation, follow STEP 3B
2-1 Loosen the four preassembled bolts using screwdriver and keep for the
use in 2-2
2-2 Secure the right wall plate [01] to the left wall plate [02] by tightening
the pre-assembled bolts.
Tighten
Loosen
2-1
2-2
DO NOT overtighten.
Tighten only until snug.
7
3A-1
3A-2
Position the wall plate at your
desired height and line up the
holes with your stud center line.
Level the wall plate and mark
the holes.
Use a stud finder (not included)
to locate wood studs or use an
awl (not included) to verify the
edges. Mark the edge and
center locations.
24in. (610mm)
16in. (406mm)
awl
(not included)
Wall
Anchor
O
X
01
02
Step 3A Wood Stud Option
WARNING:
Ensure the wall plate is securely fastened to the wall before
continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm)
minimum 1.5 x 3.5 in. (38 x 89 mm)
● Stud center must be verified
Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [G]. Tighten the lag screws [G] only until the washers [H]
are pulled firmly against the wall plate [01 and 02].
DO NOT USE ANCHOR FOR THIS STEP
8
3A-3
3A-4
Step 3B Solid Concrete or Concrete Block Option
WARNING:
Ensure the wall plate is securely fastened to the wall before
continuing to the next step.
● Mount the wall plate [01 and 02] directly onto the concrete
surface
● Anything covering the wall must not exceed 5/8 in. (16 mm)
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [G]. Tighten the lag screws [G] only until the washers [H] are pulled
firmly against the wall plate [01 and 02].
Wall
Anchor
O
Drill 4 pilot holes using a
7/32 in. (5.5 mm) diameter
drill bit. Make sure the depth
is not less than 2.56 in.
(65mm)
Install the wall plate [01 and
02] using lag screws [G] and
washer [H]. Tighten the lag
screws [G] only until the
washers [H] are pulled firmly
against the wall plate [01
and 02] .
1/2 in. (13mm)
Socket Wrench
（Not Included）
01
02
GH
ø7/32 in. (5.5mm)
2 9/16 in. (65mm)
9
3B-3
3B-1 3B-2
1/2 in. (13mm)
Socket Wrench
O
Position the wall plate at your
desired height, level the wall plate
and mark the pilot hole locations.
Drill 4 pilot holes using a 3/8 in.
(10mm) diameter drill bit. Make sure
the depth is not less than 2 3/4 in.
(70mm). Never drill into the mortar
between blocks.
Install wall plate using lag screws [G]
and washers [H] only until the washers
[H] are pulled firmly against the wall
plate. DO NOT over-tighten the lag
screws [G].
Use the hammer to knock
anchors [O] into the wall.
Be sure the anchors [O] are
seated flush with the
concrete surface.
GH
ø3/8 in. (10mm)
2 3/4 in. (70mm)
10
Step 4 Adjust Tilt Angles of TV
Step 5 Hang TV to the Wall Plate [01 and 02]
5/16in. (8mm)
Wrench
(Not Included)
Note: Do not over-tighten
or over-loosen the bolts [S]
03
04
Loosen the four preassembled tilt tension bolts [S] on both brackets. Adjust
the hooks of the brackets to the desired angle, then tighten tilt tension bolts
with a wrench (not included) and a screwdriver (not included) to fix the tilting
angle of the TV.
Note: The tilt angles of the hooks on the TV brackets must be the same
HEAVY! You may need
assistance with this step.
01
02
03
04
Top of TV
Bottom of TV
S
S
Loosen
Tighten
S
Step 6 Secure TV
Step 7 Remove the TV
11
Unlocking
Disconnect all cables, pull down and hold both cords [R] while gently pulling the bottom
of the TV away from the wall.
CAUTION: Avoid potential personal injury or property damage! To prevent breaking the locking
latches: always pull and hold the cords [R] down while pulling the TV away from the wall.
Then lift the TV up and off of wall plate assembly [01 and 02]. Place the TV on cardbard
or other protective surface to avoid damage.
NOTE: To rehang the TV, follow the procedures in Step 5 and 6.
R
Locking
Pull down and hold both cords [R], press the bottom of the TV into the wall
plate [01 and 02] until the latches lock the TV in place.
Press
R
HEAVY! You may need
assistance with this step.
01
02
Table of contents
Other Alphamount TV Mount manuals
