Alpine TME-M790 User manual

EN
DE
FR
ES
ES
SE
R
ALPINE ELECTRONICS, INC.
Tokyo office: 1-1-8 Nishi Gotanda,
Shinagawa-ku,
Tokyo 141-8501, Japan
Tel.: [phone]
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Tel.: 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF CANADA, INC.
Suite 203, 7300 Warden Ave. Markham,
Ontario L3R 9Z6, Canada
Tel.: 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue De La Belle Etoile, Z.I. Paris Nord Il
B.P. 50016 F-95945, Roissy, Charles De Gaulle
Cedex, France
Tel.: [phone]
ALPINE ELECTRONICS OF U.K., LTD.
13 Tanners Drive, Blakelands, Milton Keynes
MK14 5BU, U.K.
Tel.: [phone]
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal De Gamarra 36, Pabellón 32
01013 Vitoria (Alava)-Apdo. 133, Spain
Tel.: [phone]
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
6-8 Fiveways Boulevarde Keysborough,
Victoria 3173, Australia
Tel.: [phone]
ALPINE ELECTRONICS GmbH
Kreuzerkamp 7-11 40878 Ratingen, Germany
Tel.: [phone]
ALPINE ITALIA S.p.A.
Via C. Colombo 8, 20090 Trezzano Sul Naviglio
MI, Italy
Tel.: [phone]
TME-M790
Designed by ALPINE Japan
Printed in Japan (S)
68P30540Y57-A
• OWNER'S MANUAL
Please read before using this equipment.
• MODE D'EMPLOI
Veuillez lire avant d’utiliser cet appareil.
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
MOBILE MULTIMEDIA MONITOR
Sankei Kikaku Co., Ltd.
1-13-38, Hinodai, Hino,Tokyo, Japan

FR
ES
DE
SE
IT
1-EN
Contents
Operating Instructions
WARNING
WARNING.................................................. 2
CAUTION................................................... 3
PRECAUTIONS ......................................... 3
Basic Operations
Using Face Cover...............................................4
Initial System Start-up .......................................4
Raising the Monitor ...........................................4
Lowering the Monitor ........................................4
Turning Power On or Off...................................5
Selecting the Monitor Opening Angle ...............5
Adjusting the Monitor Viewing Angle...............5
Adjusting the Volume ........................................5
Switching the Source .........................................5
Switching Display Modes ..................................6
Other Useful Features
Adjusting Brightness of Picture .........................8
Adjusting Color Density of Picture ...................8
Adjusting Tint of Picture....................................8
Setting the Brightness of the Backlight .............9
Adjusting the Lowest Level of the Backlight ....9
Setting Automatic Opening/
Closing of Monitor.............................................9
Selecting Rear Monitor ....................................10
Setting the External Device Interrupt Mode ....10
Switching the Opening Screen.........................11
Turning Sound Guide Function On or Off.......11
Switching the Video Screen .............................11
Using the External Input Terminal...................11
Operating with the Remote Control Unit
(RUE-4165 Sold Separately) ...........................12
Information
In Case of Difficulty ........................................13
Specifications...................................................13
Installation and Connections
Warning............................................................14
Caution.............................................................14
Precautions.......................................................15
Installation .......................................................16
Connections .....................................................18
System Connections.........................................19
LIMITED WARRANTY
ENGLISH

2-EN
WARNING
This symbol means important instructions.
Failure to heed them can result in serious
injury or death.
DO NOT OPERATE ANY FUNCTION THAT TAKES
YOUR ATTENTION AWAY FROM SAFELY DRIVING
YOUR VEHICLE.
Any function that requires your prolonged attention
should only be performed after coming to a complete stop.
Always stop the vehicle in a safe location before
performing these functions. Failure to do so may result in
an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN
STILL HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
MINIMIZE DISPLAY VIEWING WHILE DRIVING.
Viewing the display may distract the driver from looking
ahead of the vehicle and cause an accident.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Use for other than its designed application may result in
fire, electric shock or other injury.
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF
THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.
DO NOT PLACE HANDS, FINGERS OR FOREIGN
OBJECTS IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the
product.
USE THE CORRECT AMPERE RATING WHEN
REPLACING FUSES.
Failure to do so may result in fire or electric shock.
WARNING
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result
in fire.
DO NOT WATCH VIDEO WHILE DRIVING.
Watching the video may distract the driver from looking
ahead of the vehicle and cause an accident.
INSTALL THE PRODUCT CORRECTLY SO THAT THE
DRIVER CANNOT WATCH TV/VIDEO UNLESS THE
VEHICLE IS STOPPED AND THE EMERGENCY BRAKE
IS APPLIED.
It is dangerous (and illegal in many states) for the driver
to watch TV/Video while driving a vehicle. Installing this
product incorrectly enables the driver to watch TV/Video
while driving. This may cause a distraction, preventing
the driver from looking ahead, thus causing an accident.
The driver or other people could be severely injured.

FR
ES
DE
SE
IT
3-EN
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or
material property damage.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to
the product. Return it to your authorized Alpine dealer or
the nearest Alpine Service Center for repairing.
KEEP FINGERS AWAY WHILE THE MOTORIZED
FRONT PANEL OR MOVING MONITOR IS IN
MOTION.
Failure to do so may result in personal injury or damage
to the product.
PRECAUTIONS
Temperature
Be sure the temperature inside the vehicle is between
+45°C (+113°F) and 0°C (+32°F) before turning your unit
on.
Fuse Replacement
When replacing the fuse(s), the replacement must be of
the same amperage as shown on the fuse holder. If the
fuse(s) blows more than once, carefully check all
electrical connections for shorted circuitry. Also have your
vehicle’s voltage regulator checked.
Maintenance
If you have problems, do not attempt to repair the unit
yourself. Return it to your Alpine dealer or the nearest
Alpine Service Station for servicing.
Installation Location
Make sure the TME-M790 will not be exposed to:
• Direct sun and heat
• High humidity
• Excessive dust
• Excessive vibrations
• After turning the system off, a slight ghost of the image
will remain temporarily. This is an effect peculiar to
LCD technology and is normal.
• Under cold temperature conditions, the screen may
lose contrast temporarily. After a short warm-up
period, it will return to normal.

4-EN
Using Face Cover
NOTES
• If the monitor touches an obstacle while it is
being raised, the unit will stop raising the
monitor immediately. Should this occur, remove the
obstacle and press the OPEN/CLOSE button again to
raise the monitor.
• When the movable monitor is opened, do not place
any object on the monitor and be careful not to bump
or apply any pressure to the monitor while it is open.
This can cause damage to the mechanism.
• Under low ambient temperature conditions, the
display may be dark for a short period of time
immediately after the power is turned on. Once the
LCD has warmed up, the display will return to
normal.
• For your safety, some operation of the unit
cannot be performed while the vehicle is in
motion. In this case, first stop the vehicle and
engage the parking brake, then perform the
operation.
Lowering the Monitor
NOTE
The TME-M790 is a precision device. With careful
handling, its performance can be maintained at a high
level for a long time.
1Press the OPEN/CLOSE button.
The unit will beep 3 times and lower the monitor
automatically.
NOTE
If the monitor touches an obstacle while it is being
lowered, the unit will stop lowering the monitor
immediately.
Should this occur, remove the obstacle and press the
OPEN/CLOSE button again to lower the monitor.
Basic Operations
Initial System Start-up
Immediately after installing or applying power to
the unit, it should be initialized.
1At the lower left corner of the screen front panel,
there is a small button. Using a pencil or other
pointed object, press this RESET switch to
complete the initialization procedure.
Raising the Monitor
NOTE
The TME-M790 is a precision device. With careful
handling, its performance can be maintained at a high
level for a long time.
1Press the OPEN/CLOSE button.
The unit beeps 3 times and raises the monitor
automatically.
RESET switch
OPEN/CLOSE
9 8 / -
PWR AUX
An anti-theft face cover is provided with the TME-
M790.
Put the face cover onto the TME-M790 when you
leave the vehicle.
Be sure to remove the anti-theft face cover when
you drive.

FR
ES
DE
SE
IT
5-EN
Turning Power On or Off
1Press the PWR (Power) button to turn on the unit.
The opening screen appears automatically.
2Press the PWR (Power) button again to turn off
the unit.
NOTES
• The TME-M790 draws minimal current even
when its power switch is turned off. If the
switched power (ignition) lead of the TME-
M790 is connected directly to the positive (+)
post of the vehicle's battery, the battery may be
discharged. If this lead is unswitched, it must
be disconnected from the battery post should
the vehicle be left unused for an extended
period of time.
An SPST (Single-Pole, Single-Throw) switch (sold
separately) can be added to simplify this procedure.
Then, you can simply place it in the OFF position
when you leave the vehicle. Turn the SPST switch
back ON before using the TME-M790. For
connecting the SPST switch, refer to the Installation.
• Some operation of the unit cannot be performed
while the vehicle is in motion. In this case, be sure to
first stop your vehicle and apply the parking brake,
then perform the operation.
• After turning the system off, a slight ghost of the
image will remain temporarily. This is an effect
peculiar to LCD technology and is normal.
• Under cold temperature conditions, the screen may
lose contrast temporarily. After a short warm-up
period, it will return to normal.
Selecting the Monitor Opening
Angle
The monitor opening angle can be set in 2
positions.
1Press and hold the OPEN/CLOSE button for at
least 2 seconds while the monitor is being
raised. Each press changes the monitor angle
back or forth.
NOTE
When the OPEN/CLOSE button is pressed and held for
at least 2 seconds when the neck angle is adjusted, the
neck angle adjustment is canceled.
After doing this, adjust the display in the front/rear
direction.
Adjusting the Monitor Viewing
Angle
Adjust the monitor's angle for better visibility.
1While viewing the screen that is shown press the
9or 8button to adjust the display to the ideal
viewing angle.
The display viewing angle can be adjusted
between 40 and 105 degrees.
2Press the 4or 3button to adjust the right-left
viewing angle. It is possible to adjust the display
viewing angle up to 15 degrees to the left or
right.
Press and hold the OPEN/CLOSE button for at
least 2 seconds to cancel the neck angle
adjustment.
NOTES
• The angle changes continuously if the 9and 8
buttons or the 4and 3buttons are held down.
• If there are any obstructions to the monitor
when adjusting the angle, first remove the
obstruction and then readjust the angle.
• The screen color will vary when viewed at certain
angles. Adjust the screen angle for the best viewing
position.
• If the voltage of the vehicle's battery power is
low, the screen may blink when the screen angle is
changed. This is normal and not a malfunction.
• The adjusted angle is stored in the memory.
Adjusting the Volume
1Press the or button to adjust the volume.
NOTE
The volume changes continuously if the or
button is held down.
Switching the Source
1Press the AUX button.Each press of the button
will cycle through the modes as follows:
NAVIGATION AUX1 AUX2

6-EN
Switching Display Modes
Viewing the switching display modes
To watch a video source, your vehicle must be
parked with the ignition key in the ACC or ON
position.To do this, follow the procedure below.
1. Push the foot brake to bring your vehicle to a
complete stop at a safe location. Engage the
parking brake.
2. Keep pushing the foot brake and release the
parking brake once then engage it again.
3. While the parking brake is being engaged the
second time, release the foot brake.
NOTE
For automatic transmission vehicles, place the
transmission lever in the Park position.
The video lock-out system is now disabled.
Unless ignition is turned OFF, this mode can be
reactivated by simply engaging the parking
brake, without performing the entire procedure
above (1 through 3).
If the ignition is turned OFF position, you must
perform the entire procedure above.
NOTE
Trying to access the switching display modes while
driving will display the warning - PICTURE OFF
FOR YOUR SAFETY.
Basic Operations
DISP
MODE 1 MODE 2 MODE 3 MODE 4
(WIDE) (ZOOM) (CINEMA) (NORMAL)
MODE 1 (WIDE)
MODE 2 (ZOOM)
1Press and hold the DISP button for at least 2
seconds.Each press changes the display modes
as follows:
Stretches the normal image evenly in a
horizontal direction so that it is displayed on the
entire screen.
Stretches the normal image evenly in a
horizontal direction so that it is displayed on the
entire screen. The stretching ratio increases the
closer to the left or right edge of the screen.

FR
ES
DE
SE
IT
7-EN
MODE 3 (CINEMA)
Stretches the normal image horizontally and
vertically.
The top and bottom of the screen is cut slightly
to adapt it to a cinema size image with a
proportion of 16:9.
A normal television broadcasting (4:3) image is
displayed in the center (normal image).
MODE 4 (NORMAL)

8-EN
Other Useful Features
SET UP
9 8 / -
AUX
Adjusting Brightness of Picture
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds and
select BRIGHT.
3Press the 4or 3button within 10 seconds to
adjust the brightness.
4Press the SET UP button to finish adjustments.
NOTE
If the AUX button is pressed and held for 2 seconds or
more while in the adjustment screen, the setting of the
brightness, color density, and tint is reset back to its
center value.
Adjusting Color Density of Picture
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds and
select COLOR.
SET UP
AUX1
BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK
MIN MAX
13
3Press the 4or 3button within 10 seconds to
adjust the color density.
4Press the SET UP button to finish adjustments.
NOTES
• If the AUX button is pressed and held for 2 seconds
or more while in the adjustment screen, the setting of
the brightness, color density, and tint is reset back to
its center value.
• The color density cannot be adjusted in the
NAVIGATION (RGB connection) mode.
Adjusting Tint of Picture
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds and
select TINT.
3Press the 4or 3button within 10 seconds to
adjust the tint.
4Press the SET UP button to finish adjustments.
NOTES
• If the AUX button is pressed and held for 2 seconds
or more while in the adjustment screen, the setting of
the brightness, color density, and tint is reset back to
its center value.
• The tint cannot be adjusted in the NAVIGATION
(RGB connection) mode.
SET UP
AUX1
–+
BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK
13
SET UP
AUX1
RG
BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK
13

FR
ES
DE
SE
IT
9-EN
Setting the Brightness of the
Backlight
It is possible to change the brightness of the LCD
panel's backlighting to more closely conform to
the vehicle's interior lighting.This makes the
screen easier to view.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds and
select DIMMER.
3Press the 4or 3button within 10 seconds to set
the value.
AUTO:
Automatic adjustment of the screen brightness in
conformity with vehicle interior brightness.
HIGH:
Maximum screen brightness.
LOW:
The preset screen brightness that was set when
adjusting the minimum backlight level.
4Press the SET UP button to finish adjustments.
Adjusting the Lowest Level of the
Backlight
It is possible with this equipment to adjust the
minimum brightness level for backlighting (LOW).
This is useful, for matching the screen brightness
to the dashboard for driving at night. This setting
is recalled with the AUTO setting corresponding
to the vehicle's interior lighting.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds and
select DIMMER Lv.
3Press the 4or 3button within 10 seconds to set
the value.
4Press the SET UP button to finish adjustments.
SET UP
AUX1
DIMMER AUTO
DIMMER Lv. -
OPEN/CLOSE OFF
OUT INT. ON
AUTO HIGH LOW
23
SET UP
AUX1
DIMMER AUTO
DIMMER Lv. -
OPEN/CLOSE OFF
OUT INT. ON
LOW HIGH
23
Setting Automatic Opening/
Closing of Monitor
Simply turn the ignition key to ACC ON or OFF to
automatically open or close the TV display.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds to
select OPEN/CLOSE.
3Press the 4or 3button within 10 seconds to set
the value.
AUTO:
Automatic opening or closing of the display in
depending upon whether the ignition switch is ON
or OFF.
OFF:
Manual opening or closing of the display.
4Press the SET UP button to finish adjustments.
SET UP
AUX1
DIMMER AUTO
DIMMER Lv. -
OPEN/CLOSE OFF
OUT INT. ON
AUTO OFF
23

10-EN
Other Useful Features
SET UP
PWR V. SEL
9 8 / -
Selecting Rear Monitor
This unit has controls to switch the video and
audio to a rear monitor if another (rear) monitor
is connected.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds and
select AUX OUT.
3Press the 4or 3button within 10 seconds to
carry out selection.
LINK:
Output the video/audio portion shown on the main
monitor, to the rear monitor.
NAV.:
Output the navigation video/audio to the rear
monitor. (Only when navigation unit is connected).
AUX 1:
Output the AUX 1 video/audio to the rear monitor.
AUX 2:
Output the AUX 2 video/audio to the rear monitor.
4Press the SET UP button to finish adjustments.
SET UP
AUX1
BRIGHT 0
COLOR 0
TINT 0
AUX OUT LINK
LINK NAV. AUX1 AUX2
13
Setting the External Device
Interrupt Mode
When used in conjunction with an Ai interception
box (KCA-801B), the sound of aTV or an
external input sound can be intercepted to an
Alpine head unit. This function may not work
with some combinations of products. For details,
refer to the KCA-801B’s operating instructions.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9or 8button within 10 seconds and
select OUT INT.
3Press the 4or 3button within 10 seconds to
turn ON.
4Press the SET UP button to finish adjustments.
SET UP
AUX1
DIMMER AUTO
DIMMER Lv. -
OPEN/CLOSE OFF
OUT INT. ON
OFF ON
23

FR
ES
DE
SE
IT
11-EN
Switching the Opening Screen
You can change the opening screen to your liking.
NOTE
After carrying out the steps 1 to 3 of "Viewing the
switching display modes" described on page 6, perform
the operation shown below.
1Press the SET UP button.
2Press the 9 or 8 button within 10 seconds and
select H.U. IND.
3Press the
9
or
9
button within 10 seconds to
set the selection.
ON:
Special opening screen.
This setting is used when combining with the
Flagship System model.
OFF:
Normal opening screen.
4Press the SET UP button to finish adjustments.
Turning Sound Guide Function
On or Off
This function will give audible feedback with
varying tones depending upon the button
pressed.
1Press and hold the PWR button for 2 seconds
with the power OFF and turn the Sound Guide
ON or OFF.
SET UP
AUX1
H.U. IND. ON
OFF ON
33
NAVIGATION AUX1 AUX2
Switching the Video Screen
It is possible to change the video source for
display while retaining the present audio portion.
1Press the V.SEL button.
2To release press and hold the V.SEL button for 2
seconds.
Using the External Input Terminal
It is possible to enjoy video and sound from a
video camera, etc. by simply connecting it with
an optional adapter cable.
NOTE
With the above connections, video source switching and
settings and adjustments at adjustment screens are not
possible.
AUDIO OUT RLVIDEO OUT
Optional adapter cable
(RCA pin plugs
[yellow, red, white]
3.5ø miniplugs).
Video camera, etc.
Main unit

12-EN
Operating with the Remote Control
Unit (RUE-4165 Sold Separately)
N/H
DEL OK
123
456
789
0
SOURCE
MENU
BAND
CANC.
POWER V.SEL
DETOUR
DISC PLAN
CHG
DEFEAT MUTE
DISP
LIST
V
O
L
D
N
V
O
L
U
P
A.PROC
VOICE MP/RG
LIST
TUNER
DISP
ON/OFF DEL DEST.
ENT
1
3
7
2
4
6
r
9
q
p
w
e
5
8
t
RUE-4165
Remote Control Signal Transmitter
Signal Transmitter Indicator
DEL
OK
8
9
0
LIST
DISP
SOURCE
MENU
BAND
CANC.
MUTE
MP/RG
POWER
DISP
ON/OFF
NAVI / AUDIO
V.SEL
DEL DEST.
ENT
Power ON/OFF.
Select the item on the adjustment screen.
Moves to the left or right when you press
on the or side.
Moves up and down when you press
on the or side.
Volume increases when turned in a
clockwise direction.
Volume decreases when turned in a
counter-clockwise direction.
Displays the adjustment screen.
Terminates the adjustment screen.
Volume decreases.
Changes continuously when held down.
Volume increases.
Changes continuously when held down.
When operating this equipment,
change to the NAVI side.
The display mode changes.
Display angle adjustment (left).
Changes continuously when held down.
Display angle adjustment (right).
Changes continuously when held down.
Display angle adjustment (down).
Changes continuously when held down.
Display angle adjustment (up).
Changes continuously when held down.
When pressed less than 2 seconds:
OPEN/CLOSE of display.
When pressed at least 2 seconds:
Display slides forward and backward.
1
2
3
4
5
6
7
8
9
Button
No.
p
q
w
e
r
t
RUE-4165 RUE-4165
Button
No.
NAVI / AUDIO
Switch the video source.
When switch 5is set to the AUDIO side.
Other Useful Features
(When the flip cover is open)
• Point the remote control transmitter
toward the remote sensor on theTME-
M790 and use the remote control within
2 meters from the TME-M790.
Remote Sensor
(when the display
is stowed away)
Remote Sensor
(when the display
is raised)
Remote Control Sensor

FR
ES
DE
SE
IT
13-EN
In Case of Difficulty
If you encounter a problem, please review the items in
the following checklist. This guide will help you isolate
the problem if the unit is at fault. Otherwise, make sure
the rest of your system is properly connected or consult
your authorized Alpine dealer.
No function or display.
• Car's ignition is off.
-Turn the ignition on.
• No fuse or blown fuse.
-Check the cause and replace the fuse.
• Incorrect connections.
-Check connection and remedy.
• Vehicle's battery is weak.
-Check the voltage of vehicle's battery.
Unclear picture display.
• Fluorescent tube is exhausted.
-Replace the fluorescent tube.*
No picture display.
• Brightness control is set for minimum brightness control.
-Adjust the brightness.
• Incorrect setting of the VCR mode.
-Switch to the correct mode.
• Protective circuit is on because of high temperature.
-Wait until the temperature inside the vehicle comes
down to the operating temperature range (45°C).
• Incorrect or open connection with the Monitor, AV
interface unit.
-Check the connection and remedy.
Picture color is poor.
• Brightness/Color/Tint control are not set to the proper
positions.
-Check each control.
Spots or dotted lines/stripes appear.
• Caused by neon signs, high-voltage power lines, CB
transmitter, other vehicle's ignition plugs, etc.
-Change the location of your vehicle.
The display angle cannot be adjusted or the
adjustment screen does not appear.
• Mechanism error.
-Press the OPEN/CLOSE button to stow away the
display, and raise the display again.
* The fluorescent tube replacement is not free of charge
even within the warranty period, for the tube is an article
of consumption.
Information
Specifications
MONITOR SECTION
Screen Size 7.0"
LCD Type Transparent type TN LCD
Operation System TFT active matrix
Number of Picture Elements 336,960 pcs. (1,440 x 234)
Effective Number of
Picture Elements 99.99% or more
Illumination System Cold cathode
fluorescent tube
AV-INTERFACE UNIT SECTION
S/N Ratio
Video 45dB
Audio 55dB
Input Level
Video 1Vp-p (75ΩUNBALANCED)
Audio 500mV (RMS)
Output Level
Video 1Vp-p (75ΩUNBALANCED)
Audio 500mV (RMS)
GENERAL
Power Requirement 14.4V DC (11-15 V allowable)
Operating temperature +32ºF to +113º(0ºC to + 45ºC)
Weight
(Monitor Section) 2.0 kg (4 lbs. 7 oz)
(AV-Interface Unit Section) 0.2 kg(7oz)
CHASSIS SIZE (Monitor section)
Width 178 mm (7")
Height 50 mm (2")
Depth 165 mm (6-1/2")
CHASSIS SIZE
(AV-Interface Unit section)
Width 106.6 mm (4-1/4")
Height 32 mm (1-1/4")
Depth 67.8 mm (2-11/16")
NOTES
• Due to continuous product improvement,
specifications and design are subject to change
without notice.
• The LCD panel is manufactured using an
extremely high precision manufacturing
technology. Its effective pixel ratio is over
99.99%. This means that there is a possibility
that 0.01% of the pixels could be either always
ON or OFF.

14-EN
Before installing or connecting the unit, please
read the following and pages 2 and 3 of this
manual thoroughly for proper use.
Warning
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire
or product damage.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE
GROUND.
(Check with your dealer if you are not sure.) Failure to do
so may result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM
THE NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due
to electrical shorts.
DO NOT ALLOW CABLES TO BECOME ENTANGLED
IN SURROUNDING OBJECTS.
Arrange wiring and cables in compliance with the manual
to prevent obstructions when driving. Cables or wiring
that obstruct or hang up on places such as the steering
wheel, gear lever, brake pedals, etc. can be extremely
hazardous.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying
capacity of the wire and result in fire or electric shock.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND
CONNECTIONS.
Bolts or nuts used for the brake or steering systems (or
any other safety-related system), or tanks should NEVER
be used for installations or ground connections. Using
such parts could disable control of the vehicle and cause
fire etc.
KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF
THE REACH OF CHILDREN.
Swallowing them may result in serious injury. If
swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT
HINDER VEHICLE OPERATION, SUCH AS THE
STEERING WHEEL OR GEARSHIFT.
Doing so may obstruct forward vision or hamper
movement etc. and results in serious accident.
Caution
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special
technical skill and experience. To ensure safety, always
contact the dealer where you purchased this product to
have the work done.
USE SPECIFIED ACCESSORY PARTS AND INSTALL
THEM SECURELY.
Be sure to use only the specified accessory parts. Use of
other than designated parts may damage this unit
internally or may not securely install the unit in place.
This may cause parts to become loose resulting in hazards
or product failure.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Route the cables and wiring away from moving parts (like
the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes
through a hole in metal, use a rubber grommet to prevent
the wire’s insulation from being cut by the metal edge of
the hole.
DO NOT INSTALL IN LOCATIONS WITH HIGH
MOISTURE OR DUST.
Avoid installing the unit in locations with high incidence
of moisture or dust. Moisture or dust that penetrates into
this unit may result in product failure.
Installation and Connections

FR
ES
DE
SE
IT
15-EN
IMPORTANT
Please record the serial number of your unit in
the space provided below and keep it as a
permanent record.The serial number plate is
located on the bottom of the unit.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
Precautions
• Be sure to disconnect the cable from the (–) battery
post before installing your TME-M790. This will
reduce any chance of damage to the unit in case of a
short-circuit.
• Be sure to connect the color coded leads according to
the diagram. Incorrect connections may cause the unit
to malfunction or damage the vehicle's electrical
system.
• When making connections to the car’s electrical
system, be aware of the factory installed components
(e.g. on-board computer). Do not tap into these leads to
provide power for this unit. When connecting the
TME-M790 to the fuse box, make sure the fuse for the
intended circuit of the TME-M790 has the appropriate
amperage. Failure to do so may result in damage to the
unit and/or the vehicle. When in doubt, consult your
ALPINE dealer.
• The TME-M790 uses female RCA-type jacks for
connection to other units (e.g. amplifier) having RCA
connectors. You may need an adaptor to connect other
units. If so, please contact your authorized ALPINE
dealer for assistance.
• The Display must be completely retracted in the casing
when installing. If it is not, problems may occur.
• When installing in automobiles, make sure the Display
can open/close without coming in contact with the shift
lever.

16-EN
Installation
Installing the Monitor
• Place of installation
Before determining the position of installation,
check that the display will not hamper gear
shifting when it is opened and closed in that
position.
NOTE
Install at an angle of within 30 degress from the
horizontal.
1
Slide mounting sleeve from main unit (see
Removal Procedure below). Slide the mounting
sleeve into the dashboard. Install the supplied
bracket to the monitor.
2
Reinforce the monitor with the metal mounting
strap (not supplied). Secure the ground lead of
the unit to a clean metal spot using a screw ( )
already attached to the vehicle’s chassis.
NOTE
For the screw marked , use an appropriate
screw for the chosen mounting location.
Installation and Connections
TME-M790
Screws(M4x5)
(Included)
Mounting Bracket
(Included)
Mounting Sleeve
(Included)
Dashboard
TME-M790
Chassis
Ground Lead
Hex Nut
(M5)
Screw
Metal Mounting Strap
Bolt Stud
Front Frame
(Included)
3
Slide the TME-M790 into the dashboard. When
the unit is in place, make sure the locking pins
are fully seated in the down position.This can be
done by pressing firmly in on the unit while
pushing the locking pin down with a small
screwdriver.This ensures that the unit is properly
locked and will not accidentally come out from
the dashboard. Install the Supplied Front Frame.
Removal
1 Use a small screwdriver (or similar tool) to
push the locking pins to the “up” position (see
above drawing). As each pin is unlocked,
gently pull out on the unit to make sure it does
not re-lock before unlocking the second pin.
2 Pull the unit out, keeping it unlocked as you do
so.
<JAPANESE CAR>
To install using the vehicle's genuine bracket
TME-M790
Screws
(M4x5)
Mounting Bracket
Ground Lead
Lock Pin

FR
ES
DE
SE
IT
17-EN
Attaching the AV-Interface Unit
When attaching with VelcroTM Tape, be sure to
choose a level location.
Do not attach in a location where the AV-
Interface unit is upside down.
Attach the AV-Interface Unit.
Attach the VelcroTM Tape included with the AV-
Interface Unit and secure the unit under the
passenger seat, for example.
TME-M790
FOOT BRAKE
(Yellow/Black)
Foot brake lamp
Foot brake lead
Pinch Connector
Pinch Connector Parking brake lead
Parking brake lamp
Parking brake switch
Foot brake switch
Battery
Chassis
(Yellow/Blue)
PARKING BRAKE
Battery
(Red)
SPST SW (Optional)
(Yellow)
TME-M790
(Monitor)
IGNITION
BATTERY
AUX OUTPUT
AUDIO VIDEO
NAVIGATION RL
AUX INPUT 1
AUDIO VIDEO
RL
AUX INPUT 2
AUDIO VIDEO
DISPLAY OUTPUT
(MONO) (MONO)
RL
VelcroTM Tape (Included)
If necessary, use a pinch connector to connect the foot brake lead, parking brake lead, etc.
Vehicle Cable
Stopper
Monitor Cable
Pinch Connector
Plier
Foot Brake Lead/Parking Brake Lead Connection
Connection Diagram of SPST Switch (Sold Separately)
(If the ACC power supply is not available)
NOTE
If your vehicle has no ACC power supply, add an SPST
(Single-Pole, Single-Throw) switch (sold separately).
If the switched power (ignition) lead of the TME-
M790 is connected directly to the positive (+) post of
the vehicle’s battery, the TME-M790 draws some
current (several hundred milliamperes) even when its
switch is placed in the OFF position and the battery
may be discharged.
12

18-EN
Installation and Connections
Monitor
Battery
White/Brown To remote input lead.
To remote input lead.
To the foot brake cord or brake lamp cord.
To the parking brake signal lead.
Ignition key
Connect to an IN INT compatible product.
White/Brown
Pink/Black
Yellow/Black
Red
Black
Yellow
Yellow/Blue
1
1
2
3
4
5
6
7
8
8
AUX OUTPUT
AUDIO VIDEONAVIGATION R L
AUX INPUT 1
AUDIO VIDEORL
AUX INPUT 2
AUDIO VIDEO
DISPLAY OUTPUT
(MONO) (MONO)
RL
REMOTE OUT
AUX1
REMOTE OUT
AUX2
AUDIO
INTERRUPT OUT
FOOT BRAKE
PARKING BRAKE
IGNITION
BATTERY
GND
Connections
1Remote Control Output Lead (White/Brown)
Connect this lead to the remote control input
lead.This lead outputs the controlling signals
from the remote control.
2Foot Brake Lead (Yellow/Black)
Connect to the vehicle’s foot brake lead or brake
lamp lead.
3Parking Brake Lead (Yellow/Blue)
Connect this lead to the power supply side of the
parking brake switch to transmit the parking
brake status signals to the TME-M790.
4Audio Interrupt Out Lead (Pink/Black)
5Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the
vehicle’s fuse box or another unused power
source which provides (+) 12V only when the
ignition is turned on or in the accessory position.
6Battery Lead (Yellow)
Connect this lead to the positive (+) post of the
vehicle’s battery.
7Ground Lead (Black)
Connect this lead to a good chassis ground on
the vehicle. Make sure the connection is made to
bare metal and is securely fastened using the
sheet metal screw provided.
8Fuse Holder (5A)
To prevent external noise from entering the
audio system.
• Locate the unit and route the leads at least
10cm away from the car harness.
• Keep the battery power leads as far away from
other leads as possible.
• Connect the ground lead securely to a bare
metal spot (remove the coating if necessary) of
the car chassis.
• If you add an optional noise suppressor,
connect it as far away from the unit as possible.
Your Alpine dealer carries various Alpine noise
suppressors, contact them for further
information.
• Your Alpine dealer knows best about noise
prevention measures so consult your dealer for
further information.