Altronix AL1042ULADA User manual
Rev. 101413
AL1042ULADA
NAC Power Extender
Installation Guide
(See Application Guide for additional information)
Altronix Corp.
140 58th St. Brooklyn, NY
- 2 - AL1042ULADA
Agency Listings:
• ULListedforControlUnitsforFireProtective
SignalingSystems(UL864).
• MEA-NYCDepartmentofBuildingsApproved.
• CSFM-CaliforniaStateFireMarshalApproved.
• FM-FactoryMutualApproved.
• NFPA72Compliant.
Input:
• Powerinput120VAC/60Hz,5amp.
• Two(2)ClassA,StyleZortwo(2)ClassB,
StyleW,YFACPinputs.
• Two(2)NCdrycontacttriggerinputs.
Output:
• Class2Ratedpowerlimitedoutputs.
• 24VDCvoltageregulatedpowerlimitedoutputs.
• 10ampmaxtotalalarmcurrent.
• 2.5Amaxcurrentperoutput.
• Twoauxiliaryoutputsratedat1ampeach
(1ampcontinuous,1ampACdisconnect).
• Programmablesupervisedindicatingcircuitoutputs:
Four(4)ClassB,StyleW,YorFour(4)ClassA,
StyleZorTwo(2)ClassA,StyleZandTwo(2)ClassB,
StyleW,Y(see Application Guide).
•Thermalandshortcircuitprotectionwithautoreset.
Battery Backup:
•Built-inchargerforsealedleadacidorgeltypebatteries.
•Automaticswitchovertostand-bybatterywhen
ACfails.
• Zerovoltagedropwhenswitchingoverto
batterybackup.
Supervision:
•ACfailsupervision(form“C”contact,1amp/28VDC).
Factorysetfor1.5hourswithoptional30seconds
delaysetting(fieldselectable).
• InstantlocalACtroublereportingrelay
(form“C”contact,1amp/28VDC).
•Batterypresenceandlowbatterysupervision
(form“C”contact,1amp/28VDC).
Visual Indicators:
•InputandoutputstatusLEDindicators.
Special Features:
• 2-wirehorn/strobeSyncmodeallowsaudible
notificationappliances(horns)tobesilenced
whilevisualnotificationappliances(strobes)
continuetooperate.
• SyncprotocolsincludePotter/Amseco,Faraday,
Gentex®,SystemSensor®,andCooperWheelock®.
• TemporalCode3,SteadyMode,InputtoOutput
FollowerMode(maintainssynchronizationof
notificationappliancescircuit).
• Compatiblewith12VDCor24VDCfirepanels.
•Outputloopsupervisiondirectedtoinput1orinput2.
•SignalCircuitTroubleMemory-facilitatesquick
identificationofanintermittent/fault(shortcircuit,open
orground)whichhaspreviouslyoccurredononeor
moresignalingcircuitoutputs.LEDsindicate/identify
whichoutputthefaulthasoccurred.
• Commontroubleinputandoutput.
• Groundfaultdetection.
•Unitincludespowersupply,logicboardenclosure,
camlock,andbatteryleads.
Enclosure Dimensions (approx. H x W x D):
18”x14.5”x4.5”(457.2mmx368.3mmx114.3mm).
Overview:
TheAltronixAL1042ULADAisanextremelycosteffective10ampremotepowersupply/batterycharger.Itmaybecon-
nectedtoany12or24voltFireAlarmControlPanel(FACP).PrimaryapplicationsincludeNotificationApplianceCircuit
(NACsuchasstrobesandhorns)expansionsupporttomeetADArequirements.Italsoprovidesauxiliarypowertosupport
systemaccessories.Theunitdeliverselectronicallyregulatedandfiltered24voltpowertoClassB,StyleW,YorClass
A,StyleZNACloopcircuits.Additionally,aseparate1ampauxiliaryoutputfor4-wiresmokedetectorsisavailable.The
10ampmax.alarmcurrentcanbedividedbetweenthefour(4)outputsforpoweringNACdevices.Eachoutputisratedat
2.5ampmax.andcanbeindependentlyprogrammedforSteady,TemporalCode3orStrobeSynchronization.Alloutputs
maybeprogrammedforInputtoOutputFollowerMode(outputwillfollowinput.i.e.MarchTimeInput,MarchTime
Output).Innon-alarmconditionindependentloopsupervisionforClassA,StyleZand/orClassB,StyleW,YFACPNAC
circuitsisprovided.Intheeventofalooptrouble,theFACPwillbenotifiedviathesteeredinput(input1orinput2).In
addition,therearecommontroubleoutputterminals[NC,C,NO]whichareusedtoindicategeneralloop/systemtrouble.
Acommontroubleinputisprovidedforoptional[NC](normallyclosed)devicestoreporttroubletotheFACP.Two(2)
FACPsignalingoutputscanbeemployedanddirectedtocontrolsupervisionandpowerdeliverytoanycombinationof
thefour(4)outputs.
Note:TheinformationinthisdocumentisvalidformodelsAL1042ULADAandAL1042UL2ADA.ModelAL1042ULADA
isequivalenttomodelAL1042UL2ADA.
Specifications:
AL1042ULADA - NAC Power Extender
AL1042ULADA - 3 -
Power Supply Specifications:
AC Input: 120VAC60Hz,5amp,suppliedbyamaximum15ampdedicatedbranchcircuit.
Output:
Four(4)regulatedsupervisedNACoutputcircuits,24VDC,2.5ampmaximumcurrent.
One(1)aux.specialapplication24VDCpoweroutputcircuit1amp,non-supervised
totaloutputcurrentmustnotexceedcurrent10ampinAlarmCondition.
Battery: Usetwo(2)12VDC/12AHortwo(2)12VDC/7AH
batteriesconnectedinseries.
Stand-by/Alarm Current
Consumption: 130mA/300mA
EOL Resistor (end of line): 2.2K(2200ohm),AltronixModel#AL-EOL22(included).
Ground fault maximum
test impedance: 1000ohm.
Stand-by Specifications:
Stand-by Batteries Stand-by Time Total Amp/Minutes Alarm Output Current Aux. Output
24VDC/7AH 24Hours 10amp/5minutes ---
24VDC/12AH
(usetwo(2)12VDCbatteriesinseries) 24Hours 10amp/5minutes 50mA
24VDC/36AH 24Hours 10amp/5minutes 1amp
Note: Unit is equipped with two (2) 1 amp max. auxiliary outputs: “AUX1” will automatically disconnect when AC
is lost. “AUX2” will remain battery backed up during power outage. For loads connected to “AUX2”, please refer
to battery “Stand-by Specifications” above for ratings. When loads are connected to the “AUX1” and or “AUX2”
outputs during alarm condition, the remaining outputs may, not exceed 10 amp total alarm current.
(example: AUX1 = 1 amp, AUX2 = 1 amp, outputs up to 8 amp).
Installation Instructions:
WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/NFPA72/ANSI,andwithalllocal
codesandauthoritieshavingjurisdiction.Productisintendedforindooruseonly.
Carefully review:
Application Guide for AL842ULADA, AL1042ULADA
Power Supply Output Specifications (pg. 3)
Stand-by Specifications (pg. 3)
Output Programming Selection Table (pg. 4)
Sync Mode Selection Table (pg. 4)
Terminal Identification Table (pgs. 5-6)
LED Diagnostics (pg. 6)
1.Mountunitinthedesiredlocation.Markandpredrillholesinthewalltolineupwiththetoptwokeyholesinthe
enclosure.Installtwoupperfastenersandscrewsinthewallwiththescrewheadsprotruding.Placetheenclosure’s
upperkeyholesoverthetwoupperscrews,levelandsecure.Markthepositionofthelowertwoholes.Removethe
enclosure.Drillthelowerholesandinstallthetwofasteners.Placetheenclosure’supperkeyholesoverthetwoupper
screws.Installthetwolowerscrewsandmakesuretotightenallscrews(Enclosure Dimensions, pg. 12).
2. Connectgreenleadtoearthground (Fig 1).Connecttheline(L)andneutral(N)terminalstoaseparateunswitched
ACcircuit(120VAC,60Hz)dedicatedtotheFireAlarmSystem.
3. Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.
4. Connectbatterytotheterminalsmarked[+BAT--]onthePowerSupplyBoard(batteryleadsincluded).
Note:IfbatteriesbeingusedinyourinstallationdonotfitintotheAL1042ULADAunit,itisrequiredtoinstalla
separateenclosure,ULListedforappropriateapplication.Separatebatteryenclosureisrequiredtohave50cubicinches
ofadditionalopenspace.AllwiringmethodsshallbeinaccordancewiththeNationalElectricalCode
NFPA70/NFPA72/ANSIandwithalllocalcodesandauthoritieshavingjurisdiction.Batterycircuitsarenotpower-
limited;provide0.25”spacingfrompower-limitedcircuitsanduseseparateknockout.Ifadditionalbatteryenclosure
isrequired,itmustbeULListedfortheapplicationandmountedwithin5’oftheAL1042ULADAenclosureinthe
sameroom;minimum12AWGwireinappropriateconduitisrequiredforconnection.Whenusingconduit,make
sureitisinstalledinamatterwhereitcannotturn.
5. Setoutputselectionswitchesmarked[OUT1throughOUT4]tofollowcorrespondinginput[IN1&IN2]
anddesiredoutputsignaltype (Output Programming Selection Table, pg. 4).
L N
line
ground
neutral
Fig. 1
- 4 - AL1042ULADA
6. ConnectFACPoutputtothedesiredAL842LGKlogicboardinputs,andnotificationappliancestothedesiredAL842LGK
logicboardoutputs(see Application Guide).
Note:The2-wirehorn/strobesyncmodewillonlysynchronizehorns,horn/strobes,strobeswith
synchronizationcapability.
7. Forconnectionofsmokedetectors,digitaldialerseeOptional Hookup Diagram, pg. 8.
Output Programming Selection Table:
Outputs must be programmed independently (OUT1 - OUT4)
Function Switch Positions Descriptions
ON OFF
InputtoOutputFollower
Mode 1 2,3
Outputfollowssignalitreceivesfromthecorrespondinginput
(i.e.FACPSyncmodule-maintainssynchronizationof
notificationappliancecircuit).
TemporalCode3Mode 3 1,2 EnablesTemporalCode3signalgenerationoutput.
Thismodewillacceptasteadyorapulsinginput.
SteadyMode 1,2,3 Asteadyoutputsignalwillbegenerated.
Thismodewillacceptsteadyorpulsinginput.
For the above modes Dip Switch 4 determines which Input controls the corresponding output:
Switch 4 in the ON position causes output(s) to be controlled by input 1.
Switch 4 in the OFF position causes output(s) to be controlled by input 2.
Sync Mode Selection Table:
Function Switch Positions Descriptions
ON OFF
AmsecoSync
Mode*
1,3,
42
ThismodeisdesignedtoworkwiththeAmsecoseriesofhorns,strobes,and
horn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,
synchronizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/
strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
Faraday
SyncMode* 2,4 1,3
ThismodeisdesignedtoworkwiththeFaradayseriesofhorns,strobes,andhorn/
strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchroniz-
ingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobecombi-
nationoveratwo-wirecircuitwhileleavingstrobesactive.
Gentex®
SyncMode
Gentexisaregisteredtrademarkof
GentexCorporation.
1,2,
3,4
ThismodeisdesignedtoworkwiththeGentex®seriesofhorns,strobes,andhorn/
strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchroniz-
ingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobecombi-
nationoveratwo-wirecircuitwhileleavingstrobesactive.
SystemSensor®
SyncMode*
SystemSensorisaregistered
trademarkofHoneywell.
1,2,4 3
ThismodeisdesignedtoworkwiththeSystemSensor®seriesofhorns,strobes,and
horn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,syn-
chronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsofthe
horn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
CooperWheelock®
SyncMode*
CooperWheelockisa
registeredtrademarkof
CooperWheelock.
2,3,4 1
ThismodeisdesignedtoworkwiththeCooperWheelockseriesofhorns,strobes,
andhorn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,
synchronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsof
thehorn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
Note:TheAL1042ULADAwillonlysynchronizehorns,horn/strobesandstrobesthatcontainsynchronizationcapability.
Contactsignalmanufacturerformoredetailedinfo.Thesamesynchronizationmodemustbeselectedforalloutputs.
Note: It is required to control visual notification appliances (strobes) via input 1 [IN1] and audible notification
appliances (horns) via input 2 [IN2]. This allows audible notification appliances (horns) to be silenced while
visual notification appliances (strobes) continue to operate.
AL842LGK Board
(Output Dip Switches)
INPUT SELECT
TEMPORAL
STROBE SYNC
IN>OUT SYNC
AL1042ULADA - 5 -
Amount of Notification Appliances per NAC:
Amseco 27perNAC* SystemSensor® 32perNAC*
Faraday 39perNAC* CooperWheelock® 32perNAC*
Gentex® 32perNAC*
*Not to exceed a maximum of 2.5 amp per NAC.
Terminal Identification Table:
AL842LGK - Logic Board
Terminal Legend Function/Description
IN1+,IN1-
IN2+,IN2-
(Supervised)
These terminals connect to the 12VDC or 24VDC FACP notification appliance circuit outputs.
(ClassA,StyleZorClassB,StyleW,Y)Inputtriggervoltageis8-33VDC@5mAmin.Terminal
polarityisshowninalarmcondition.Duringanalarmconditiontheseinputswillcausetheselected
outputschosentodrivenotificationappliances.Thedesignatedoutputsaresetbyoutputswitches
[OUT1through OUT4] (Output Programming Selection Table, pg. 4).A trouble condition onan
output loop will cause the corresponding input to trip the FACP by opening the FACP loop. An
alarmconditionwillalwaysoverridetroubletodrivenotificationappliances.
RET1+,RET1-
RET2+,RET2-
(Supervised)
ForClassA,StyleZhookupstheseterminalpairsreturntoFACPNAC1and/orNAC2.
ForClassB,StyleW,YhookupstheFACPEOLresistorfromtheNAC1and/orNAC2outputsare
terminatedattheseterminals.Optionally,othernotificationappliancesoradditionalsignalingcircuit
powersuppliesmaybeconnectedtotheseterminals.IfthisoptionischosentheEOLresistormust
beterminatedatthelastdevice.
C“DRY1”NC
C“DRY2”NC
(Dryinputtrigger)
Anopenacrosstheseinputs,willcausetheselectedoutputschosentodrivenotificationappliances.
Thedesignated outputs are set by output switches [OUT1 throughOUT4] (Output Programming
Selection Table, pg. 4).Notetheseinputsareunidirectionalandwillnotreportatroublecondition
totheFACP.
+OUT1--
+OUT2--
+OUT3--
+OUT4--
(Supervised)
Notificationappliancesareconnectedtotheseregulatedoutputs(see Application Guide, pgs. 2-4).
Eachpower-limitedoutputwillsupply2.5amp.Totalsupplycurrentis10amp(see note below).
Outputsarecontrolledbydesignatedinput1[IN1]orinput2[IN2] (Output Programming Selection
Table, pg. 4).Maximumlinelossorvoltagedrop(testedwith2.5V).
+Loop1--
+Loop2--
+Loop3--
+Loop4--
UsedforClassA,StyleZhook-upstoterminateloopsoriginatingon[OUT1],[OUT2],[OUT3],
and[OUT4]respectively.
C“FAULT”NC
(Common
troubleinput)
Anopencircuitacrossthispairofterminalswillcause[INP1andINP2]LEDstosimultaneouslysig-
nalatroubleconditionbacktotheFACP(TypicallyusedtoreportACorBATFail).(Fig. 3a, pg. 8).
NC,C,NO
(Common
troubleinput)
These are dry contact trouble outputs that report any general loop/system trouble conditions.
(Typicallyusedtotriggeradigitalcommunicatororotherreportingdevices).
(form“C”contact1amp/28VDC0.35PowerFactor)(Fig. 3, pg. 8).
--AUX+
Thisseparate1ampmax.auxiliaryspecialapplicationpoweroutputcircuitistypicallyusedtopower
electromagneticdoorholdersthatkeepfireandsmokedoorsopenundernormalconditions.
See Appendix A, pgs. 10-12.
--AUX2+
Thisseparateauxiliaryregulatedpoweroutputcircuitsuppliesupto1ampduringstand-byandalarm
condition.SincethisoutputisnotdisconnectedfromitsloadduringACpowerfailureusethe(Battery
Calculation Worksheet, pg. 9)todeterminebatterysizeand/orallowablestand-byandalarmcurrent.
+DC-- 24VDCfrompowersupply.
Note: Unit is equipped with two (2) 1 amp max. auxiliary outputs: “AUX1” will automatically disconnect when AC
is lost. “AUX2” will remain battery backed up during power outage. For loads connected to “AUX2” please, refer
to battery “Stand-by Specifications” above for ratings. When loads are connected to the “AUX1” and or “AUX2”
outputs during alarm condition, the remaining outputs may, not exceed 10 amp total alarm current.
(example: AUX1 = 1 amp, AUX2 = 1 amp, outputs up to 8 amp).
- 6 - AL1042ULADA
Terminal Identification Table:
Power Supply Board
Terminal Legend Function/Description
L,N Connect120VACtotheseterminals:LtoHot,NtoNeutral.
-DC+ 24VDC@10ampcontinuous,10ampinalarmnonpower-limitedoutput.
ACFAIL
NO,C,NC
Form“C”drycontactsindicatethelossofAC,withACpresentterminalsmarked[NOandC]are
open,[NCandC]areclosed.WhenlossofACoccursterminalsmarked[NOandC]areclosed,
[NCandC]areopen.
ACLOCAL
NC,NO,C
Form“C”drycontactsusedtoinstantaneouslysignalthelossACtolocalannunciationdevices,
withACpresentterminalsmarked[NOandC]areopen,[NCandC]areclosed.Whenlossof
ACoccursterminalsmarked[NOandC]areclosed,[NCandC]areopen.
BATFAIL
NO,C,NC
Form“C”drycontactsindicatelowbatteryvoltageorlossofbatteryvoltage.Undernormal
conditionsterminalsmarked[N.O.andC]areopen,[NCandC]areclosed.Duringatrouble
conditionterminalsmarked[N.O.andC]areclosed,and[N.C.andC]areopen(Fig. 3, pg. 8).
+BAT- Stand-bybatteryinput(leadsprovided)(Fig. 3, pg. 8).
*Power Board Parameter Specifications:
• ACFailconditionwillreportapproximately1.5hoursafterlossofAC.TosetACDelayto30seconds,powertheunit
down(ACsupplyandBattery)priortochangingswitchposition.Openorclose“ACDelay”switch,respectively.
• Lowbatteryconditionwillreportatapproximately20VDC.
• Batterypresencedetectionwillreportwithin180secondsafterbatteryremainsundetected(missingorremoved).
Arestoredbatterywillreportwithin30seconds.
LED Diagnostics:
Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normaloperatingcondition.
ON OFF LossofAC,Stand-bybatterysupplyingpower.
OFF ON NoDCoutput.
OFF OFF LossofAC.Dischargedornostand-bybattery.NoDCoutput.
AL842LGK - Logic Board
LED OFF ON BLINK (LONG)* BLINK (SHORT)**
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
Input1 Normal AlarmCondition TroubleCondition ---
Input2 Normal AlarmCondition TroubleCondition ---
Fault Normal AlarmCondition --- ---
* Indicatesexistingtroublecondition.Whenatroublecondition(open,shortorground)occursonaspecificoutput,the
correspondingredoutputLED,[OUT1-OUT4]willblink.ThecorrespondinggreeninputLEDwillblinkaswell.
**Indicatestroubleconditionmemory.Whenatroubleconditionrestores,theunitsredoutputLEDs,[OUT1-OUT4]
willblinkwithashorteranddistinctlydifferentduration.ThegreeninputLEDswillbeoff(normalcondition).
ToresetthememorydepresstheresetbuttonlocatedontheAL842LGKlogicboard(Fig. 2c, pg. 8).
TheLED(s)willextinguish.
Note: Whenindicatingcircuitshaverestored,troublememoryresetisnotrequiredfornormaloperation.
AL1042ULADA - 7 -
External
Jacketed
Shield
Incorrect Wire
Handling
Correct Wire
Handling
Pull back
external jacketed
shield approx. 1/2”.
Wire
Insulation
Solid Copper
Conductors
NEC Power-Limited Wiring Requirements for AL1042ULADA Models:
Power-limitedandnonpower-limitedcircuitwiringmustremainseparatedinthecabinet.Allpower-limitedcircuitwiring
mustremainatleast0.25”awayfromanynonpower-limitedcircuitwiring.Furthermore,allpower-limitedcircuitwiring
andnonpower-limitedcircuitwiringmustenterandexitthecabinetthroughdifferentconduits.Onesuchexampleofthis
isshownbelow.Yourspecificapplicationmayrequiredifferentconduitknockoutstobeused.Anyconduitknockoutsmay
beused.Forpower-limitedapplications,useofconduitisoptional.Allfieldwiringconnectionsmustbemadeemploying
suitablegaugeCMorFPLjacketedwire(orequivalentsubstitute).
OptionalbatteryenclosuremustbemountedadjacenttothepowersupplyviaClass1wiringmethods.
Note:RefertowirehandlingdrawingbelowfortheproperwaytoinstalltheCMorFPLjacketedwire,(Fig, 2a).
Fig, 2
Fig, 2a
120VACInput
60Hz
(nonpower-limited)
Supervisory
Connections
(power-limited)
non-supervised
Battery
Connections
(nonpower-
limited)
supervised
NACCircuits
(power-limited)
supervised
and
Aux.Output
(power-limited)
non-supervised
NACCircuits
(power-limited)
supervised
SignalingCircuitsfromFACP
(nonpower-limited)
supervised
- 8 - AL1042ULADA
OUT1 OUT2 OUT3 OUT4
INP2 INP1
FAULT
RESET
OUT1 OUT3
OUT2 OUT4
IN>OUT SYNC
STROBE SYNC
TEMPORAL
INPUT SELECT
IN>OUT SYNC
STROBE SYNC
TEMPORAL
INPUT SELECT
NC C NO C "FAULT" NC
+ DC ---
-- AUX2 +
-- LOOP4 +
-- OUT4 +-- OUT3 +
-- LOOP3 +-- LOOP1 +
-- OUT1 +-- OUT2 +
-- LOOP2 +
-- IN1 +
-- RET1 +
-- IN2 +
-- RET2 +
NC "DRY1" C
NC "DRY2" C
-- AUX1 +
Addressable
control module
trigger output
(See Typical Application Diagram for device hookup)
Power-Limited Outputs 2.5 amp per output max. (total = 10 amp)
+ --
4-wire Smoke
Detector
+ --
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL Resistor
from FACP
Digital Communicator
or Local Annunciator
Dry output Contact
(Form "C" contacts)
These circuits are used to
monitor AC and Bat Fail
and will cause a
simultaneous trouble
condition to the FACP's
IN1 and IN2
(Non-Supervised)
Factory Installed Board
Interface Cable
AC
Magnetic
Door Holder
stand-by battery
connection
(non power-limited)
BAT FAIL
AC FAIL
+ BAT –+DC --
DC AC
AC DELAY
NC C NO NC C NO
AC LOCAL
NC C NO
L
N
Battery and AC Supervision
Circuit (power-limited).
Use separate knockout.
6.3A 250V
15
15A 32V
line
neutral
unswitched
120VAC
power mains
(non power-limited)
Optional hookups:
1- BatteryandACmonitoring:ACorBatteryFailconditionwillcausethecommontroubleinput[C“FAULT”NC]to
reportbacktotheFACPviainput1andinput2.Thecommontroubleinputmayalsobeusedforotheroptional
supervisorymonitoring.
ToreportACandBatteryTroubleconnectthebatteryandACFailrelayoutputshowninFig. 3a, pg. 8tothe
commontroubleinput.
2- Drycontactinput(C“DRY1”NC)(C“DRY2”NC)canbeusedtoalarmoutputfroman
addressablemodule(theseinputsareunidirectionandcannotreportbacktotriggermodule).
Connection to triggering devices must be made within 20ft. of distance and using conduit for wiring.
3- Auxiliaryoutput(-AUX+)24VDCat1ampmax.
4- ACLocal[NC,NO,C]shouldconnecttothehostcontrolpanelforlocalannunciationofthetroublecondition.
Note: Ifcommontroubleinput,terminalsmarked[C“FAULT”NC]arenotused,theseterminalsmustbe
shorted(connectjumper)toremaininactive.ForoptionalhookupsseeFig. 3b, pg. 8.
Optional Hookup Diagram:
Fig. 3 Fig. 3a
Fig. 3b
Fig. 3c
Maintenance:
Unitshouldbetestedatleastonceayearfortheproperoperationasfollows:
Output Voltage Test:Undernormalloadconditions,theDCoutputvoltageshouldbecheckedforpropervoltagelevel
(26.2-26.4VDC recommended range).
Battery Test:Undernormalloadconditionscheckthatthebatteryisfullycharged.Checkspecifiedvoltage
bothatbatteryterminalandattheboardterminalsmarked[+BAT--]toensurethatthereisnobreakinthebattery
connectionwires.
Fuses:Checkinputandoutputfusesonthepowersupplyboard,replaceifnecessary.
Inputfuseratingis6.3amp@250V,Outputfuseratingis15amp@32V.
Note:Maximumchargingcurrentis1.5amp.
Note:Expectedbatterylifeis5years;however,itisrecommendedchangingbatteriesin4yearsorlessifneeded.
OUT1 OUT2 OUT3 OUT4
INP2 INP1
FAULT
RESET
OUT1 OUT3
OUT2 OUT4
IN>OUT SYNC
STROBE SYNC
TEMPORAL
INPUT SELECT
IN>OUT SYNC
STROBE SYNC
TEMPORAL
INPUT SELECT
NC C NO C "FAULT" NC
+ DC ---
-- AUX2 +
-- LOOP4 +
-- OUT4 +-- OUT3 +
-- LOOP3 +-- LOOP1 +
-- OUT1 +-- OUT2 +
-- LOOP2 +
-- IN1 +
-- RET1 +
-- IN2 +
-- RET2 +
NC "DRY1" C
NC "DRY2" C
-- AUX1 +
Addressable
control module
trigger output
(See Typical Application Diagram for device hookup)
Power-Limited Outputs 2.5 amp per output max. (total = 10 amp)
+ --
4-wire Smoke
Detector
+ --
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL Resistor
from FACP
Digital Communicator
or Local Annunciator
Dry output Contact
(Form "C" contacts)
These circuits are used to
monitor AC and Bat Fail
and will cause a
simultaneous trouble
condition to the FACP's
IN1 and IN2
(Non-Supervised)
Factory Installed Board
Interface Cable
AC
Magnetic
Door Holder
stand-by battery
connection
(non power-limited)
BAT FAIL
AC FAIL
+ BAT –+DC --
DC AC
AC DELAY
NC C NO NC C NO
AC LOCAL
NC C NO
L
N
Battery and AC Supervision
Circuit (power-limited).
Use separate knockout.
6.3A 250V
15
15A 32V
line
neutral
unswitched
120VAC
power mains
(non power-limited)
NC C NO C "FAULT" NC
TroubleMemory
ResetButton
+ DC ---
BAT FAIL
NO C NC NO C NC
+ BAT ---
L G N
DC
AC FAIL
AC
15A
32V
10A
250V
OUT1 OUT2 OUT3 OUT4
INP2 INP1
FAULT
RESET
OUT1 OUT3
OUT2 OUT4
IN>OUT SYNC
STROBE SYNC
TEMPORAL
INPUT SELECT
IN>OUT SYNC
STROBE SYNC
TEMPORAL
INPUT SELECT
NC C NO C "FAULT" NC
+ DC ---
-- AUX2 +
-- LOOP4 +
-- OUT4 +-- OUT3 +
-- LOOP3 +-- LOOP1 +
-- OUT1 +-- OUT2 +
-- LOOP2 +
-- IN1 +
-- RET1 +
-- IN2 +
-- RET2 +
NC "DRY1" C
NC "DRY2" C
-- AUX1 +
Green Lead
Addressable
controlmodule
triggeroutput
(See Typical Application Diagram for device hookup)
Power-Limited Outputs 2.5 amp per output max.
(total = 10 amp)
+ --
4-wire Smoke
Detector
+ --
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL Resistor
from FACP
Digital Communicator or
Local Annunciator Dry
output Contact
(Form "C" contacts)
These circuits are used to monitor
AC and Bat Fail and will cause a
simultaneous trouble condition
to the FACP's IN1 and IN2
(Non-Supervised)
Factory Installed
Board Interface
Cable
AC
Fuse
Cover
unswitched 115VAC
50/60Hz, 4.4 amp
power mains
(non power-limited)
Magnetic
Door Holder
AL1042ULADA - 9 -
Battery Calculation Worksheet
Device Number of
Devices Current per Device Stand-by
Current
Alarm
Current
Foreachdeviceusethisformula: Thiscolumn x Thiscolumn = Equals Currentpernumberofdevices.
AL1042ULADA
(Currentdrawfrombattery) 1Stand-by: 130mA 130mA
Alarm: 300mA 300mA
AAL1042 Current 130mA 300mA
AuxiliaryDevices Refertodevicemanualforcurrentratings.
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
BAuxiliary Devices Current (must not exceed 1 amp)
Refertodevicemanualforcurrentratings.
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
CNotificationAppliancesCurrent must notexceed10amp(10,000mA) 0mA mA
DTotalalarmcurrent mA mA
ETotalcurrentratingsconvertedtoamperes(lineDx0.001) A A
FNumberofstand-byhours(24forNFPA72,Chapter1,1-5.2.5). H
GMultiplylinesEandF. Totalstand-byAH AH
HAlarmsoundingperiodinhours.
(Forexample,5minutes=.0833hours.) H
IMultiplylinesEandH. TotalalarmAH AH
JAddlinesGandI. Totalstand-byandalarmAH AH
K
MultiplylineJby1.30.
(30%extrainsurancetomeetdesiredperformance)
Totalampere-hoursrequired
AH
Unitsarecapableofrecharging36AHbatterymax.Iftotalampere-hourrequiredexceeds36AH,
decreaseAUXcurrenttoprovideenoughstand-bytimefortheapplication.
- 10 - AL1042ULADA
Appendix A - UL/cUL Listed Compatible Devices for Synchronization
A-1 Strobes, Horns and Horn/Strobes
TableA-1belowlistsStrobes,HornsandHorn/StrobescompatiblewithAL1042ULADANACoutputs.
Gentex:
GCS24CR-UL GCCB24PCR/W-UL GEC24-15/75WR-UL
GCS24CW-UL GCCG24PCR/W-UL GEC24-15/75WW-UL
GCS24PCR-UL GCCR24PCR/W-UL SSPK24CLPR-UL
GCS24PCW-UL WGESA24-75PWR/W-UL SSPK24CLPW-UL
GCC24CR-UL WGESB24-75PWR/W-UL SSPK24WLPR-UL
GCC24PCR-UL WGESG24-75PWR/W-UL SSPK24WLPW-UL
GCC24CW-UL WGESR24-75PWR/G-UL SSPK24AWR-UL
GCC24PCW-UL WGECA24-75PWR/W-UL SSPK24AWW-UL
GES3-24WR-UL WGECB24-75PWR/W-UL SSPK24-15/75WLPR-UL
GEC3-24WR-UL WGECG24-75PWR/W-UL SSPK24-15/75WLPW-UL
GEH24-R-UL WGECR24-75PWR/G-UL SSPK24-15/75AWR-UL
GEH24-W-UL WGESA24-75PWLPR/W-UL SSPK24-15/75AWW-UL
WGES24-75WR/WW-UL WGESB24-75PWLPR/W-UL SSPKA24-15/75PWR-UL
WGES24-75PWR/PWW-UL WGESG24-75PWLPR/W-UL SSPKA24-15/75PWW-UL
WGES24-75WRLP/WWLP-UL WGESR24-75PWLPR/W-UL SSPKA24-15/75AWR-UL
WGEC24-75WR/WW-UL WGECA24-75PWLPR/W-UL SSPKA24-15/75AWW-UL
WGEC24-75PWR/PWW-UL WGECB24-75PWLPR/W-UL SSPKB24-15/75PWR-UL
WGEC24-75WRLP/WWLP-UL WGECG24-75PWLPR/W-UL SSPKB24-15/75PWW-UL
WGEC24-75PWRLP/WWLP-UL WGECR24-75PWLPR/W-UL SSPKG24-15/75PWR-UL
GESA24PWR/W-UL GX91-R/W-UL/cUL SSPKG24-15/75PWW-UL
GESB24PWR/W-UL GX91-PR/W-UL/cUL SSPKR24-15/75PWR-UL
GESG24PWR/W-UL GX93-R/W-UL/cUL SSPKR24-15/75PWW-UL
GESR24PWR/W-UL GX93-PR/W-UL/cUL WSSPKA24-15/75AWR-UL
GECA24PWR/W-UL WSSPK24-15/75WR/WW-UL WSSPKA24-15/75AWW-UL
GECB24PWR/W-UL WSSPK24-15/75PWR/PWW-UL WSSPKA24-15/75PWR-UL
GECG24PWR/W-UL WSSPK24-15/75AWR/AWW-UL WSSPKA24-15/75PWW-UL
GECR24PWR/W-UL GES24-177WR-UL WSSPKB24-15/75PWR-UL
GCSA24PCR/W-UL GES24-177WW-UL WSSPKB24-15/75PWW-UL
GCSB24PCR/W-UL GES24-15/75WR-UL WSSPKG24-15/75PWR-UL
GCSG24PCR/W-UL GES24-15/75WW-UL WSSPKG24-15/75PWW-UL
GCSR24PCR/W-UL GEC24-177WR-UL WSSPKR24-15/75PWR-UL
GCCA24PCR/W-UL GEC24-177WW-UL WSSPKR24-15/75PWW-UL
System Sensor:
CHSR-UL P4R-SP-UL PC4RH-P-UL SPSCW-UL SPSWK-CLR-ALERT-UL
CHSW-UL P4RH-UL PC4RH-SP-UL SPSCW-CLR-ALERT-UL SPSWK-P-UL
HR/HRK/HW-UL P4RH-P-UL PC4W-UL SPSCW-P-UL SPSWK-R-UL
MHR-UL P4RH-SP-UL PC4W-P-UL SPSCWH-UL SPSWV-UL
MHW-UL P4RK-UL PC4W-SP-UL SPSCWH-P-UL SPSWV-P-UL
P1224MC-UL P4RK-R-UL PC4WH-UL SPSCWHK-UL SR-UL
P2R-UL P4W-UL PC4WH-P-UL SPSCWHK-P-UL SR-P-UL
P2R-P-UL P4W-P-UL PC4WH-SP-UL SPSCWK-UL SR-SP-UL
P2R-SP-UL P4W-SP-UL PC4WHK-UL SPSCWK-CLR-ALERT-UL SRH-UL
P2RH-UL P4WH-UL PC4WK-UL SPSCWK-R-UL SRH-P-UL
P2RH-LF-UL P4WH-P-UL SCR-UL SPSCWV-UL SRH-SP-UL
P2RH-P-UL P4WH-SP-UL SCR-P-UL SPSCWV-P-UL SRHK-UL
P2RH-SP-UL P4WK-UL SCR-SP-UL SPSCWVH-UL SRHK-P-UL
P2RHK-UL PC2R-UL SCRH-UL SPSCWVH-P-UL SRHK-R-UL
P2RHK-P-UL PC2R-P-UL SCRH-P-UL SPSR-UL SRK-UL
P2RHK-R-UL PC2RH-UL SCRH-SP-UL SPSR-P-UL SRK-P-UL
P2RK-UL PC2RH-P-UL SCRHK-UL SPSRH-UL SRK-R-UL
P2RK-P-UL PC2RH-SP-UL SCRK-UL SPSRH-P-UL SW-UL
P2RK-R-UL PC2RHK-UL SCW-UL SPSRHK-UL SW-ALERT-UL
P2W-UL PC2RK-UL SCW-CLR-ALERT-UL SPSRK-UL SW-CLR-ALERT-UL
P2W-P-UL PC2W-UL SCW-P-UL SPSRK-P-UL SW-P-UL
P2W-SP-UL PC2W-P-UL SCW-SP-UL SPSRK-R-UL SW-SP-UL
P2WH-UL PC2W-SP-UL SCWH-UL SPSRV-UL SWH-UL
P2WH-LF-UL PC2WH-UL SCWH-P-UL SPSRV-P-UL SWH-ALERT-UL
P2WH-P-UL PC2WH-P-UL SCWH-SP-UL SPSW-UL SWH-P-UL
P2WH-SP-UL PC2WH-SP-UL SCWHK-UL SPSW-ALERT-UL SWH-SP-UL
P2WHK-UL PC2WHK-UL SCWK-UL SPSW-CLR-ALERT-UL SWHK-UL
P2WHK-P-UL PC2WK-UL SPSCR-UL SPSW-P-UL SWHK-P-UL
P2WK-UL PC4R-UL SPSCRH-UL SPSWH-UL SWK-UL
P2WK-P-UL PC4R-P-UL SPSCRV-UL SPSWH-P-UL SWK-P-UL
P4R-UL PC4R-SP-UL SPSCRVH-UL SPSWK-UL
P4R-P-UL PC4RH-UL
AL1042ULADA - 11 -
Appendix A - UL/cUL Listed Compatible Devices for Synchronization (cont’d)
A-1 Strobes, Horns and Horn/Strobes
TableA-1belowlistsStrobes,HornsandHorn/StrobescompatiblewithAL1042ULADA NACoutputs.
Potter/Amseco:
CM24CR-UL CSL-1224W-BW-UL/cUL MH-12/24W-UL/cUL SSC8-177R-UL
CM24CW-UL CSL-1224W-GR-UL/cUL SCM24C-177R-UL SSC8-177W-UL
CSH-1224W-AR-UL/cUL CSL-1224W-GW-UL/cUL SCM24C-177W-UL SSC8-3075110R-UL
CSH-1224W-AW-UL/cUL CSL-1224W-RR-UL/cUL SCM24C-3075110R-UL SSC8-3075110W-UL
CSH-1224W-BR-UL/cUL CSL-1224W-RW-UL/cUL SCM24C-3075110W-UL SSR2-177R-UL
CSH-1224W-BW-UL/cUL CSL24CAW-UL/cUL SH-1224R-UL/cUL SSR2-177W-UL
CSH-1224W-GR-UL/cUL CSL24C-BW-UL/cUL SH-1224W-UL/cUL SSR2-3075110R-UL
CSH-1224W-GW-UL/cUL CSL24C-GW-UL/cUL SH-1224WP-R-UL/cUL SSR2-3075110W-UL
CSH-1224W-RR-UL/cUL CSL24C-RW-UL/cUL SH-1224WP-W-UL/cUL SSR8-177R-UL
CSH-1224W-RW-UL/cUL CSL24C-AR-UL/cUL SH24C-177R-UL/cUL SSR8-177W-UL
CSH24C-AW-UL/cUL CSL24C-BR-UL/cUL SH24C-177W-UL/cUL SSR8-3075110R-UL
CSH24C-BW-UL/cUL CSL24C-GR-UL/cUL SL-1224R-UL/cUL SSR8-3075110W-UL
CSH24C-GW-UL/cUL CSL24C-RR-UL/cUL SL-1224W-UL/cUL SSS2-1530R-UL
CSH24C-RW-UL/cUL H-1224R-UL/cUL SL-1224WP-R-UL/cUL SSS2-1530W-UL
CSH24C-AR-UL/cUL H-1224W-UL/cUL SL-1224WP-W-UL/cUL SSS2-75110R-UL
CSH24C-BR-UL/cUL HP-25TR-UL/cUL SL-24W-UL/cUL SSS2-75110W-UL
CSH24C-GR-UL/cUL HP-25TW-UL/cUL SSC2-177R-UL SSS8-1530R-UL
CSH24C-RR-UL/cUL MH-12/24R-UL/cUL SSC2-177W-UL SSS8-1530W-UL
CSL-1224W-AR-UL/cUL MH-12/24TR-UL/cUL SSC2-3075110R-UL SSS8-75110R-UL
CSL-1224W-AW-UL/cUL MH-12/24TW-UL/cUL SSC2-3075110W-UL SSS8-75110W-UL
CSL-1224W-BR-UL/cUL
Cooper/Wheelock:
50-241575W-FR-UL/cUL E70-24MCW-FN-UL/cUL ET90-24MCCH-FN-UL/cUL LSTW-A*-UL/cUL
AH-24WP-R-UL E70-24MCW-FR-UL/cUL ET90-24MCCH-FW-UL/cUL LSTW-ALA*-UL/cUL
AMT-12/24-R-UL/cUL E70-24MCW-FW-UL/cUL HNR-UL/cUL LSTW-NA*-UL/cUL
AMT-12/24-W-UL/cUL E70-24MCWH-FN-UL/cUL HNRC-UL/cUL LSTW-NA*-UL/cUL
AMT-241575W-FR-UL/cUL E70-24MCWH-FR-UL/cUL HNW-UL/cUL MIZ-24S-R-UL/cUL
AMT-241575W-FR-NYC-UL E70-24MCWH-FR-UL/cUL HNWC-UL/cUL MIZ-24S-W-UL/cUL
AMT-241575W-FW-UL/cUL E70-24MCWH-FW-UL/cUL HS-24-R-UL/cUL MT-12/24-R-UL
AMT-24MCW-FR-UL/cUL E70H-241575W-FR-UL/cUL HS-24-W-UL/cUL MT-241575W-FR-UL/cUL
AMT-24MCW-FW-UL/cUL E70H-241575W-FW-UL/cUL HS4-241575W-FR-UL/cUL MT-241575W-FW-UL/cUL
AS-12100C-UL/cUL E70H-24MCW-FR-UL/cUL HS4-24MCC-FR-UL MT-24MCW-FR-UL/cUL
AS-24100C-UL/cUL E70H-24MCW-FW-UL/cUL HS4-24MCC-FW-UL/cUL MT-24MCW-FW-UL/cUL
ASWP-2475C-FR-UL E70H-24MCWH-FN-UL/cUL HS4-24MCW-FR-UL/cUL MTWP-2475C-FR-UL
ASWP-2475C-FW-UL E70H-24MCWH-FW-UL/cUL HS4-24MCW-FW-UL/cUL MTWP-2475C-FW-UL
ASWP-2475W-FR-UL E90-24MCC-FN-UL/cUL HSR-UL/cUL MTWP-2475W-FR-UL
ASWP-2475W-FW-UL ET90-24MCC-FW-UL/cUL HSRC-UL/cUL MTWP-2475W-FW-UL
ASWP-24MCCH-FR-UL ET90-24MCC-FN-UL/cUL HSW-UL/cUL MTWP-24MCCH-FR-UL
ASWP-24MCCH-FW-UL E90-24MCC-FR-UL/cUL HSWC-UL/cUL MTWP-24MCCH-FW-UL
ASWP-24MCWH-FR-UL E90-24MCC-FW-UL/cUL LHNR*-UL/cUL MTWP-24MCWH-FR-UL
ASWP-24MCWH-FW-UL E90-24MCCH-FN-UL/cUL LHNW*-UL/cUL MTWP-24MCWH-FW-UL
CH70-24MCW-FR-UL/cUL E90-24MCCH-FR-UL/cUL LHSR*-UL/cUL RSS-241575W-FR-UL/cUL
CH70-24MCW-FW-UL/cUL E90-24MCCH-FW-UL/cUL LHSR-A*-UL/cUL RSS-241575W-FW-UL/cUL
CH70-24MCWH-FR-UL/cUL E90H-24MCC-FR-UL/cUL LHSR-AL*-UL/cUL RSS-24MCW-FR-UL/cUL
CH70-24MCWH-FW-UL/cUL E90H-24MCC-FW-UL/cUL LHSR-N*-UL/cUL RSS-24MCW-FW-UL/cUL
CH90-24MCC-FR-UL/cUL E90H-24MCCH-FR-UL/cUL LHSW*-UL/cUL RSS-24MCWH-FR-UL/cUL
CH90-24MCC-FW-UL/cUL E90H-24MCCH-FW-UL/cUL LHSW-A*-UL/cUL RSS-24MCWH-FW-UL/cUL
CH90-24MCCH-FR-UL/cUL EET90-24MCCH-FR-UL/cUL LHSW-AL*-UL/cUL RSSA-24MCC-NW-UL
CH90-24MCCH-FW-UL/cUL ET-1010-R-UL LHSW-N*-UL/cUL RSSA-24MCCH-NW-UL
E50-241575W-FW-UL/cUL ET-1010-W-UL LSPSTR*-UL/cUL RSSB-24MCC-NW-UL
E50-24MCWH-FR-UL/cUL ET70-241575W-FR-UL/cUL LSPSTR-AL*-UL/cUL RSSB-24MCCH-NW-UL
E50-24MCWH-FW-UL/cUL ET70-241575W-FW-UL/cUL LSPSTR-ALA*-UL/cUL RSSG-24MCC-NW-UL
E50H-241575W-FR-UL/cUL ET70-24MCW-FN-UL/cUL LSPSTR-N*-UL/cUL RSSG-24MCCH-NW-UL
E50H-241575W-FW-UL/cUL ET70-24MCW-FR-UL/cUL LSPSTR-NA*-UL/cUL RSSR-24MCC-NW-UL
E50H-24MCW-FR-UL/cUL ET70-24MCW-FW-UL/cUL LSPSTW*-UL/cUL RSSR-24MCCH-NW-UL
E50H-24MCW-FW-UL/cUL ET70-24MCWH-FN-UL/cUL LSPSTW-AL*-UL/cUL RSSWP-2475C-FR-UL
E50H-24MCWH-FR-UL/cUL ET70-24MCWH-FR-UL/cUL LSPSTW-ALA*-UL/cUL RSSWP-2475C-FW-UL
E50H-24MCWH-FW-UL/cUL ET70-24MCWH-FW-UL/cUL LSPSTW-N*-UL/cUL RSSWP-2475W-AR-UL
E60-24MCC-FR-UL/cUL ET70WP-24185W-FR-UL LSPSTW-NA*-UL/cUL RSSWP-2475W-FR-UL
E60-24MCC-FW-UL/cUL ET70WP-24185W-FW-UL LSTR*-UL/cUL RSSWP-2475W-FW-UL
E60-24MCCH-FR-UL/cUL ET70WP-2475C-FR-UL LSTR-A*-UL/cUL RSSWP-2475W-NW-UL
E60-24MCCH-FW-UL/cUL ET70WP-2475C-FW-UL LSTR-AL*-UL/cUL RSSWP-24MCCH-FR-UL
E60H-24MCC-FR-UL/cUL ET80-24MCW-FR-UL/cUL LSTR-ALA*-UL/cUL RSSWP-24MCCH-FW-UL
E60H-24MCC-FW-UL/cUL ET80-24MCW-FW-UL/cUL LSTR-NA*-UL/cUL RSSWP-24MCWH-FR-UL
E60H-24MCCH-FR-UL/cUL ET80-24MCWH-FR-UL/cUL LSTRW-ALA*-UL/cUL RSSWP-24MCWH-FW-UL
E60H-24MCCH-FW-UL/cUL ET80-24MCWH-FW-UL/cUL LSTW*-UL/cUL S8-24MCC-FW-UL/cUL
*WhenusingthesemodelstrobesthemaximumcurrentperNACislimitedto2amp.
- 12 - AL1042ULADA
Appendix A - UL/cUL Listed Compatible Devices for Synchronization (cont’d)
A-1 Strobes, Horns and Horn/Strobes
TableA-1belowlistsStrobes,HornsandHorn/StrobescompatiblewithAL1042ULADA NACoutputs.
Cooper/Wheelock:
S8-24MCCH-FW-UL/cUL STH-3R24MCCH-NR-UL STR-ALB-UL STW-ALB-UL
SA-S70-24MCW-FR-UL STH-4M30WC-UL STR-NA-UL STW-NA-UL
SA-S70-24MCW-FW-UL STH-4MS-R-UL STR-NB-UL STW-NB-UL
SA-S90-24MCC-FR-UL STH-4R-UL STR-NG-UL STW-NG-UL
SA-S90-24MCC-FW-UL STH-4R24MCCH-NW-UL STR-NR-UL STW-NR-UL
STH-2G-UL STH-4R24MCCH110B-NR-UL STRC-NA-UL STWC-AB-UL
STH-2MS-R-UL STH-4R24MCCH110R-NA-UL STRC-NB-UL STWC-ALA-UL
STH-2R-UL STH-4R24MCCH110R-NR-UL STRC-NG-UL STWC-ALB-UL
STH-2R24MCCH-NR-UL STH-90-4R24MCCH-NW-UL STRC-NR-UL STWC-NA-UL
STH-3MS-R-UL STR-AB-UL STW-AB-UL STWC-NB-UL
STH-3R-UL STR-ALA-UL STW-ALA-UL STWC-NG-UL
STWC-NR-UL
Appendix B - UL Listed Compatible Devices
B.1 Four (4) Wire Smoke Detectors
TableB-1belowlistsfour(4)wiresmokedetectorscompatiblewithAL1042ULADAAUXoutputandOutputs1-8when
programmedasAUX.
System Sensor
Smoke Detector/BaseDetector Type Max Stand-by
Current (mA)
Alarm
Current (mA)
B112LP Base 0.12 36
B114LP Base * *
B404B Base * *
DH100ACDC Photoelectric 0.15 0.70
DH100ACDCLP Photoelectric 0.15 0.70
DH100ACDCLPW Photoelectric 0.15 0.70
DH400ACDCI IonizationDuct 25 95
DH400ACDCP PhotoelectricDuct 25 95
1112/24/D Ionization 0.05 50
1424 Ionization 0.10 41
1451(w/B402BBase) Ionization 0.10 39
2112/24ATR Photoelectric 0.50 60/70
2112/24AITR Photoelectric 0.50 60/70
2112/24/D Photoelectric 0.05 50
2112/24R Photoelectric 0.50 60/70
2112/24TR Photoelectric 0.50 60/70
2112/24T/D Photoelectricw/135oThermal 0.05 50
2112/24TSRB Photoelectricw/135oThermalSupervisoryRelay 15 45
2312/24TB Photoelectric 0.12 50
2412(12volt) Photoelectric 0.12 77
2412AT(12volt) Photoelectric 0.12 58
2412TH(12volt) Photoelectric 0.12 77
2424 Photoelectric 0.10 41
2424TH Photoelectric 0.10 41
2451 Photoelectric 0.10 39
2451TH(with/B402BBase) Photoelectric 0.10 39
2W-MOD LoopTest/MaintenanceMod. 30 50
4W-B(12/24volt) PhotoelectricI30.05 23
4WT-B(12/24volt) PhotoelectricI3w/Therm 0.05 23
4WTA-B(12/24volt) I3Photow/Therm/Sounder 0.05 35
4WTR-B(12/24volt) I3Photow/Therm/Relay 0.05 35
4WTR-B(12/24volt) I3Photow/Therm/Sounder/Relay 0.05 50
4WITAR-B(12/24volt) I3Photow/IsolatedTherm/Sounder/Relay 0.05 50
2W-MOD2 I3LoopTest/MaintenanceMod. 0.05 *
RRS-MOD I3ReversingRelay/SyncModule 0.05 *
6424 ProjectedBeam 10 28.4
Beam1224(S) ProjectedBeam 17 38.5
*Contactmanufacturerforcurrentdraws.
B.2 Relays
TableB-3belowlistsrelayscompatiblewithAL1042ULADAAUXoutputandOutputs1-8whenprogrammedasAUX.
Manufacturer Model Current (mA) Manufacturer Model Current (mA) Manufacturer
System
Sensor
PR-1 15
System
Sensor
R-10T 23
System
Sensor
R-10E 23
PR-2 30 R-14T 23 R-14E 23
PR-3 30 R-20T 40 R-20E 40
EOLR-1 30 R-24T 40 R-24E 40
AL1042ULADA - 13 -
Notes:
- 14 - AL1042ULADA
Notes:
AL1042ULADA - 15 -
Notes:
- 16 - AL1042ULADA
Altronixisnotresponsibleforanytypographicalerrors.
14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-9056
website:www.altronix.com,e-mail:[email protected],LifetimeWarranty,MadeinU.S.A.
IIAL1042ULADA F13N MEMBER
1.5”
(38.1mm)
1.0”
(25.4mm)
4.5”
(114.3mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.0”
(25.4mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
8.5”
(215.9mm)
18.0”
(457.2mm)
18.0”
(457.2mm)
18.0”
(457.2mm)
6.0”
(152.4mm)
2.5”
(63.5mm)
2.75”
(69.85mm)
2.75”
(69.85mm)
4.5”
(114.3mm)
4.5”
(114.3mm)
14.5”
(368.3mm)
14.5”
(
368.3mm
)
1.0”
(25.4mm)
1.0”
(25.4mm)
14.5”
(368.3mm)
2.5”
(63.5mm)
1.5”
(38.1mm)
2.5”
(63.5mm)
Enclosure Dimensions (H x W x D approximate):
18”x14.5”x4.5”(457.2mmx368.3mmx114.3mm)
Other manuals for AL1042ULADA
2
This manual suits for next models
1
Table of contents
Other Altronix Batteries Charger manuals
Altronix
Altronix OLS120 User manual
Altronix
Altronix AL1024X220 Series User manual
Altronix
Altronix AL125ULB User manual
Altronix
Altronix OLS350220 User manual
Altronix
Altronix AL6003X220 User manual
Altronix
Altronix OLS75/220 User manual
Altronix
Altronix AL600ULX Series User manual
Altronix
Altronix LPS3AC User manual
Altronix
Altronix SMP7CT 220 Series User manual
Altronix
Altronix OLS200220 User manual
Altronix
Altronix AL100UL User manual
Altronix
Altronix WayPoint102 User manual
Altronix
Altronix AL176X220 User manual
Altronix
Altronix OLS180 User manual
Altronix
Altronix OLS200 User manual
Altronix
Altronix AL175220 User manual
Altronix
Altronix AL1024X220 Series User manual
Altronix
Altronix CommBatt1 User manual
Altronix
Altronix LPS3WP12 User manual
Altronix
Altronix AL400ULXJ User manual
