Altronix Trove T2KK3F8 User manual

T2KK3F8
8 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM8 - Fused Access Power Controller
- (1) T16100 Transformer
T2KK3F8Q
8 Door Kit with Fused Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8 - Fused Access Power Controller
- (1) T16100 Transformer
T2KK3F8D
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM8CB - PTC Access Power Controller
- (1) T16100 Transformer
T2KK3F8DQ
8 Door Kit with PTC Outputs
Fully assembled kit includes:
- Trove2 enclosure with TKA2 Altronix/Keyscan backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8CB - PTC Access Power Controller
- (1) T16100 Transformer
Access & Power Integration
Rev. TKK072817
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
All registered trademarks are property of their respective owners. More than just power.™
Installation Guide

- 2 - T2KK Kits
Overview:
Altronix Trove Keyscan kits are pre-assembled and consist of Trove2KA2 enclosure/backplane with factory installed Altronix
power supply/charger, transformer, and sub-assemblies. These kits also accommodate various combinations of Keyscan boards
for up to eight (8) doors in a single enclosure.
Configuration Chart:
Altronix
Model
Number
Nominal DC
Output Voltage
Maximum Supply Current
for Main and Aux. Outputs
on Power Supply board
and ACM8/ACM8CB
Access Power Controller’s
outputs (A)
Fail-Safe/Fail-Secure or Dry Form “C” Outputs Fail-Safe/Fail-Secure Outputs (auto-resettable) 120VAC 60Hz Input Current (A) Current Per ACM8 Output (A) Current Per ACM8CB Output (A) Power Supply Board Input Fuse Rating Power Supply Board Battery Fuse Rating ACM8/ACM8CB Board Input Fuse Rating ACM8 Board Output Fuse Rating ACM8CB Board Output PTC Rating
[DC] [Aux]
24VDC Output Range (V) 24VDC Output Range (V)
T2KK3F8 20.19-26.4 20.19-26.4 24VDC @ 5.8A 8 - 3.5 2.5 - 5A/
250V
10A/
32V
10A/
250V 2.5A -
T2KK3F8Q 20.19-26.4 20.19-26.4 24VDC @ 5.8A 8 - 3.5 2.5 - 5A/
250V
10A/
32V
10A/
250V 2.5A -
T2KK3F8D 20.17-26.4 20.28-26.4 24VDC @ 5.8A - 8 3.5 - 2.0 6.3A/
250V
15A/
32V
10A/
250V - 2A
T2KK3F8DQ 20.17-26.4 20.28-26.4 24VDC @ 5.8A - 8 3.5 - 2.0 6.3A/
250V
15A/
32V
10A/
250V - 2A
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI and with all local codes and authorities having
jurisdiction. Product is intended for indoor use only.
1. Remove backplane from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location, opposite hinge.
Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2).
Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.
To activate alarm signal open the door of the enclosure.
4. Mount Keyscan boards to backplane, refer to page 3.
5. Refer to the eFlow Power Supply/Charger Installation Guide (for eFlow6NB),
Sub-Assembly Installation Guide (ACM8(CB) and LINQ2),
and T16100 Installation Instructions (T16100) for further installation instructions.
Fig. 1
Edge of
Enclosure
to Access Control
Panel or
UL Listed
Reporting
Device
Enclosure
Tamper
Switch
(provided)

T2KK Kits - 3 -
LINQ2 (T2KK3F8(D)Q)
Altronix
T16100
Altronix
eFlow6NB
Altronix ACM8(CB)
TKA2: Configuration of Keyscan Boards
1. Mount appropriate Keyscan boards into the correct positions (Fig. 2, pg. 2) by postioning standoffs over appropriate holes in the
backplane and depressing down on board to secure standoff to the backplane (Fig. 2b, pg. 2).
2. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).
Fig. 2
Plastic Standoff
pre-mounted into
Keyscan modules
Insert into
TKA2 backplane
Fig. 2b

- 4 - T2KK Kits
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
web site: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
IITrove2KA2 Kit Series A16S MEMBER
Enclosure Dimensions (H x W x D approximate):
27.25” x 21.5” x 6.5” (692.2mm x 552.5mm x 165.1mm)
G
1.25”
(31.75mm)
1.25”
(31.75mm)
6.25”
(158.75mm)
6.25”
(158.75mm)
6.75”
(171.45mm)
8.25”
(209.54mm)
8.00”
(203.2mm)
1.5”
(38.1mm)
1.25”
(31.75mm)
0.85”
(21.59mm)
0.85”
(21.59mm)
1.00”
(25.4mm)
2.00”
(50.8mm)
1.25”
(31.75mm)
2.00”
(
50.8mm
)
2.00”
(
50.8mm
)
5.25”
(
133.35mm
)
5.25”
(
133.35mm
)
7.00”
(
177.79mm
)
2.00”
(50.8mm)
2.00”
(50.8mm)
27.00”
(685.8mm)
3.50”
(88.9mm)
0.5625”
(14.29mm)
2.415”
(61.34mm)
0.685”
(17.399mm)
1.77”
(44.96mm)
3.50”
(88.9mm)
21.50”
(546.1mm)
19.80”
(502.92mm)
5.25”
(133.35mm)
5.25”
(133.35mm)
0.885” (22.479mm)
1.125” (28.32mm)
Knockouts