Altronix AL802ADA220J User manual

Rev. 122713 More than just power.TM
AL802ADA220J
NAC Power Extender
Installation Guide
(see Application Guide for additional information)

- 2 - AL802ADA220J
Overview:
Altronix AL802ADA220J is an extremely cost-effective 8A remote power supply/battery charger. It may be
connected to any 12 or 24 volt Fire Alarm Control Panel (FACP). Primary applications include Notification
Appliance Circuit (NAC such as strobes and horns) expansion support to meet ADA requirements. It also pro-
vides auxiliary power to support system accessories. The unit delivers electronically regulated and filtered 24 volt
power to Class B, Style W, Y or Class A, Style Z NAC loop circuits. Additionally, a separate 1.0A auxiliary out-
put with reset for four (4)-wire smoke detectors is available. The 8A max. alarm current can be divided between
the four (4) outputs for powering NAC devices. Each output is rated at 2.5A max., and can be independently
programmed for Steady, Temporal Code 3 or Strobe Synchronization. All outputs may be programmed for Input
to Output Follower Mode (output will follow input, i.e. March Time Input, March Time Output). In non-alarm
condition independent loop supervision for Class A, Style Z and/or Class B, Style W, Y FACP NAC circuits is
provided. In the event of a loop trouble, the FACP will be notified via the steered input (input 1 or input 2). In
addition, there are common trouble output terminals [NC, C, NO] which are used to indicate general loop/system
trouble. A common trouble input is provided for optional NC (normally closed) devices to report trouble to the
FACP. Two (2) FACP signaling outputs can be employed and directed to control supervision and power delivery
to any combination of the four (4) outputs.
Specifications:
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.
Input:
• Power input 220VAC (working range 198VAC-
256VAC), 50/60 Hz, 1.5A.
• Two (2) Class A, Style Z or two (2) Class B,
Style W, Y FACP inputs.
• Two (2) NC dry contact trigger inputs.
Output:
• 24VDC @ 8A max total alarm current.
• 2.5A max current per output.
• Separate 1.0A auxiliary output.
• Programmable supervised indicating circuit outputs:
Four (4) Class B, Style W, Y or Two (2) Class A,
Style Z or One (1) Class A, Style Z and Two (2)
Class B, Style W, Y (see Application Guide).
• Thermal and short circuit protection with auto reset.
Battery Backup:
• Built-in charger for sealed lead acid or
gel type batteries.
• Automatic switchover to stand-by battery when
AC Fails.
• Zero voltage drop when switching over to
battery backup.
Supervision:
• AC fail supervision (form “C” contact, 1A/28VDC).
Factory set for 30 seconds with optional 2.5 to 3
hour delay setting (field selectable).
• Instant local AC trouble reporting relay
(form “C” contact, 1A / 28VDC).
• Battery presence and low battery supervision
(form “C” contact, 1A / 28VDC).
Visual Indicators:
• Input and output status LED indicators.
Special Features:
• 2-wire horn/strobe Sync mode allows audible
notification appliances (horns) to be silenced
while visual notification appliances (strobes)
continue to operate.
• Sync protocols include Potter/Amseco, Faraday,
Gentex®,System Sensor®, and CooperWheelock®.
• Temporal Code 3, Steady Mode, Input to Output
Follower Mode (maintains synchronization of
notification appliances circuit).
• Compatible with 12VDC or 24VDC fire panels.
• Output loop supervision steered to Input 1 or Input 2.
• Signal circuit trouble memory (helps identify
intermittent loop problems).
• Common trouble input and output.
• Ground fault detection.
Added Features:
• Unit includes power supply, red enclosure, cam
lock, and battery leads.
Enclosure Dimensions (approx. H x W x D):
18” x 14.5” x 4.5”
(457.2mm x 368.3mm x 114.3mm).

AL802ADA220J - 3 -
Power Supply Specifications:
AC Input: 220VAC, 50/60Hz, 1.5A, supplied by a maximum 15A dedicated branch circuit.
Output:
Four (4) regulated supervised NAC output circuits, 24VDC, 2.5A maximum
current. One (1) aux. special application 24VDC power output circuit 1A, non-
supervised total output current must not exceed current 8A in Alarm Condition.
Battery Use two (2) 12VDC/7AH or two (2) 12VDC/12AH batteries connected in series.
Stand-by/Alarm
Current Consumption: 90mA/175mA
EOL Resistor (end of line): 2.2K (2200 Ohm), Altronix Model # AL-EOL22 (included).
Ground fault maximum
test impedance: 1000 Ohm.
Stand-by Specifications:
Stand-by Batteries Stand-by Time Total
(A/Minutes) Alarm Output Current Aux. Output
24VDC/7AH 24 Hours 8A/5 minutes –
24VDC/12AH
(use two 12VDC batteries in series) 24 Hours 8A/5 minutes 50mA
24VDC/36AH 24 Hours 8A/5 minutes 1A
Note: Unit is equipped with 1A max. auxiliary output: “AUX” will remain battery backed up during
power outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” above for
ratings. When loads are connected to “AUX” output during alarm condition, the remaining outputs may,
not exceed 8A total alarm current (example: AUX = 1A, outputs up to 7A).
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with
all local codes and authorities having jurisdiction.
Product is intended for indoor dry use only.
Carefully review:
Application Guide for AL602ADA220J, AL802ADA220J, AL1002ADA220J
Power Supply Specifications (pg. 3)
Stand-by Specifications (pg. 3)
Output Programming Selection Table (pg. 4)
Sync Mode Selection Table (pg. 4)
Terminal Identification Table (pgs. 5-6)
LED Status Indication Table (pg. 6)
1. Mount the unit in the desired location. Mark and predrill holes in the wall to
line up with the top two keyholes in the enclosure. Install two upper fasteners
and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of
the lower two holes. Remove the enclosure. Drill the lower holes and install two
fasteners. Place the enclosure’s upper keyholes over the two upper screws.
Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 16).
Secure enclosure to earth ground. Small terminal block wire gauges range from 16 AWG to 24 AWG,
all others range from 14 AWG to 24 AWG.
2. Connect the line (L) and neutral (N) terminals to a separate unswitched AC circuit (220VAC, 50/60Hz)
dedicated to the Fire Alarm System. Secure ground wire lead to ground lug (Fig. 1, pg. 3).
3. Measure output voltage before connecting devices.This helps avoiding potential damage.
4. Connect battery to the terminals marked [+ BAT –] on the Power Supply Board (battery leads included).
Use two (2) 12VDC batteries connected in series.
5. Set output selection switches marked [OUT1 through OUT4] to follow corresponding input [IN1 & IN2]
and desired output signal type (Output Programming Selection Table, pg. 4).
6. Connect FACP output to the desired AL800LGK9E logic board inputs, and notification appliances to the
desired AL800LGK9E logic board outputs (see Application Guide).
Note: The 2-wire horn/strobe sync mode will only synchronize horns, horn/strobes, strobes with
synchronization capability.
7. For connection of smoke detectors, digital dialer see Optional Hookup Diagram, pg. 8.
Fig. 1
L N
Line
Neutral
Ground Lug

- 4 - AL802ADA220J
Class A, Style Z Class B, Style W, X, Y, SW1 & SW2 Settings:
• For all Class B, Style W, X, Y hookups SW1 and SW2 on the AL800LGK logic board must be turned OFF.
For all Class A, Style Z hookups SW1 and SW2 on the AL800LGK logic board must be turned ON.
Output Programming Selection Table:
Outputs must be programmed independently (OUT1 - OUT4)
Function Switch Positions Descriptions
ON OFF
Input to Output
Follower Mode 12, 3
Output follows signal it receives from the corresponding
input (i.e. FACP Sync module - maintains synchronization
of notification appliance circuit).
Temporal Code 3 Mode 31, 2 Enables Temporal Code 3 signal generation output.
This mode will accept a steady or a pulsing input.
Steady Mode 1, 2, 3 A steady output signal will be generated.
This mode will accept steady or pulsing input.
For the above modes DIP Switch 4 determines which Input controls the
corresponding output:
Switch 4 in the ON position causes output(s) to be controlled by Input 1.
Switch 4 in the OFF position causes output(s) to be controlled by Input 2.
Sync Mode Selection Table:
Function Switch Positions Descriptions
ON OFF
Amseco
Sync Mode*
1, 3,
42
This mode is designed to work with the Amseco series of horns,
strobes, and horn/strobes to provide a means of synchronizing
the Temporal-coded horns, synchronizing the flash timing of the
strobe, and silencing the horns of the horn/strobe combination over
a two-wire circuit while leaving strobes active.
Faraday
Sync Mode* 2, 4 1, 3
This mode is designed to work with the Faraday series of horns,
strobes, and horn/strobes to provide a means of synchronizing the
Temporal-coded horns, synchronizing the flash timing of the strobe,
and silencing the horns of the horn/strobe combination over a two-
wire circuit while leaving strobes active.
Gentex®
Sync Mode*
Gentex is a registered
trademark of
Gentex Corporation.
1, 2,
3, 4
This mode is designed to work with the Gentex®series of horns,
strobes, and horn/strobes to provide a means of synchronizing
the Temporal-coded horns, synchronizing the flash timing of the
strobe, and silencing the horns of the horn/strobe combination
over a two-wire circuit while leaving strobes active.
System Sensor®
Sync Mode*
System Sensor is a
registered trademark of
Honeywell.
1, 2, 4 3
This mode is designed to work with the System Sensor®series of
horns, strobes, and horn/strobes to provide a means of synchroniz-
ing the Temporal-coded horns, synchronizing the one-second flash
timing of the strobe, and silencing the horns of the horn/strobe
combination over a two-wire circuit while leaving strobes active.
CooperWheelock®
Sync Mode*
CooperWheelock is a
registered trademark of
Cooper Wheelock.
2, 3, 4 1
This mode is designed to work with the CooperWheelock series of
horns, strobes, and horn/strobes to provide a means of synchronizing
the Temporal-coded horns, synchronizing the one-second flash tim-
ing of the strobe, and silencing the horns of the horn/strobe combina-
tion over a two-wire circuit while leaving strobes active.
*Note: The AL802ADA220J will only synchronize horns, horn/strobes and strobes that contain synchronization
capability. Contact signal manufacturer for more detailed info.
The same synchronization mode must be selected for all outputs
Note: It is required to control visual notification appliances (strobes) via Input 1 (IN1) and audible noti-
fication appliances (horns) via Input 2 (IN2). This allows audible notification appliances (horns) to be
silenced while visual notification appliances (strobes) continue to operate.
AL800LGK9E Board
Output DIP Switches
INPUT SELECT
TEMPORAL
STROBE SYNC
IN>OUT SYNC

AL802ADA220J - 5 -
Amount of Notification Appliances per NAC:
Amseco 27 per NAC* System Sensor®32 per NAC*
Faraday 39 per NAC* CooperWheelock®32 per NAC*
Gentex®32 per NAC*
*Not to exceed a maximum of 2.5A per NAC.
Terminal Identification Table:
AL800LGK9E Logic Board
Terminal Legend Function/Description
IN1+, IN1–
IN2+, IN2–
(Supervised)
These terminals connect to the 24VDC FACP notification appliance circuit outputs.
(Class A, Style Z or Class B, Style W, X, Y) Input trigger voltage is 8-33VDC @ 5mA
min. Terminal polarity is shown in alarm condition. During an alarm condition these
inputs will cause the selected outputs chosen to drive notification appliances. The desig-
nated outputs are set by output switches [OUT1 through OUT4] (Output Programming
Selection Table, pg. 4). A trouble condition on an output loop will cause the corre-
sponding input to trip the FACP by opening the FACP loop. An alarm condition will
always override trouble to drive notification appliances.
RET1+, RET1–
RET2+, RET2–
(Supervised)
For (Class A, Style Z hookups these terminal pairs return to FACP NAC1 and/or
NAC2. For Class B, Style W, X, Y hookups the FACP EOL resistor from the NAC1
and/or NAC2 outputs are terminated at these terminals.
C “DRY1” NC
C “DRY2” NC
(Dry input trigger)
An open across these inputs, will cause the selected outputs chosen to drive notification
appliances. The designated outputs are set by output switches [OUT1 through OUT4]
(Output Programming Selection Table, pg. 4). Note these inputs are unidirectional and
will not report a trouble condition to the FACP.
+ OUT1 –
+ OUT2 –
+ OUT3 –
+ OUT4 –
(Supervised)
Notification appliances are connected to these regulated outputs (see 02 Application
Guide pg. 2-4). Each power-limited output will supply 2.5A. Two (2) outputs may be
connected in parallel for a maximum NAC output capability of 4A. Total supply current is
8A (see note below). Outputs are controlled by designated Input 1 [IN1] or Input 2 [IN2]
(Output Programming Selection
C “FAULT” NC
(Common
trouble input)
An open circuit across this pair of terminals will cause [IN1 and IN2] to simultaneously
signal a trouble condition back to the FACP (Typically used to report AC or BAT Fail).
Form “C” contact 1A / 28VDC (Fig. 2, pg. 8).
NC, C, NO
(Common
trouble output)
These are dry contact trouble outputs that follow any general loop/system trouble
conditions. (Typically used to trigger a digital communicator or other reporting device).
Form “C” contact 1A / 28VDC, 0.35 Power Factor (Fig. 2, pg. 8).
– AUX+
This separate 1A max auxiliary Special Application Power output circuit is typically
used to power 4-wire smoke detectors. See attached list of devices
(Appendix A, pgs. 10-12).
– DC + 24VDC from power supply.
Note: Unit is equipped with 1A max. auxiliary output: “AUX” will remain battery backed up during
power outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications”, pg. 3 for
ratings. When loads are connected to “AUX” output during alarm condition, the remaining outputs may
not exceed 8A total alarm current (example: AUX = 1A, outputs up to 7A).

- 6 - AL802ADA220J
Terminal Identification Table:
AL800ADA Power Supply Board*
Terminal
Legend Function/Description
L, G, N Connect 220VAC to these terminals: L to hot, N to neutral.
–DC + 24VDC @ 8A in alarm non power-limited output.
AC FAIL
NO, C, NC
Form “C” dry contacts used to instantaneously signal the loss AC to local annunciation devices,
with AC present terminals marked NO and C are open, NC and C are closed. When loss of AC
occurs terminals marked NO and C are closed, NC and C are open.
AC LOCAL
NC, NO, C
Form “C” dry contacts used to instantaneously signal the loss AC to local annunciation devices,
with AC present terminals marked NO and C are open, NC and C are closed. When loss of AC
occurs terminals marked NO and C are closed, NC and C are open.
BAT FAIL
NO, C, NC
Form “C” dry contacts used to signal low battery voltage or loss of battery voltage.
Under normal conditions terminals marked NO and C are open, NC and C are closed. During a
trouble condition terminals marked NO and C are closed, and NC and C are open (Fig. 2, pg. 8).
+ BAT –Stand-by battery input (leads provided) (Fig. 2, pg. 8).
*Power Board Parameter Specifications:
• AC Fail condition will report approximately 30 seconds after loss of AC. To delay report for 2.5 to 3 hours
cut jumper AC DELAY on the Power Supply Board (AC trouble output delay option). If this mode is
selected the Power Supply Board must be reset by removing all power to it for 30 seconds.
• Low battery condition will report at approximately 21VDC.
• Battery presence detection will report within 180 seconds after battery remains undetected (missing or
removed). A restored battery will report within 30 seconds.
LED Diagnostics:
AL800ADA - Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery is supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
AL800LGK9E - Logic Board
LED OFF ON BLINK (LONG)* BLINK (SHORT)**
Output 1 Normal Alarm Condition Trouble Condition Trouble Condition Memory
Output 2 Normal Alarm Condition Trouble Condition Trouble Condition Memory
Output 3 Normal Alarm Condition Trouble Condition Trouble Condition Memory
Output 4 Normal Alarm Condition Trouble Condition Trouble Condition Memory
Input 1 Normal Alarm Condition Trouble Condition –
Input 2 Normal Alarm Condition Trouble Condition –
Fault Normal Alarm Condition – –
* Indicates current trouble condition. When trouble (open, short or ground) occurs on a specific output, the
corresponding red output LED, [OUT1-OUT4] will blink. The corresponding green input LED will
blink as well. Loop trouble will report within 30 seconds.
** Indicates trouble condition memory. When a trouble condition restores, the units red output LED,
[OUT1-OUT4] will blink with a shorter and distinctly a different duration.
The green input LEDs will be off (normal condition).
To reset the memory depress the reset button (Fig. 2c, pg. 8). The LED(s) will extinguish.
Note: If indicating circuits have been restored, memory reset is not required for normal operation of the unit.

AL802ADA220J - 7 -
Battery Calculation Worksheet
Device Number of
Devices Current per Device Stand-by
Current
Alarm
Current
For each device use this formula: This column x This column = Equals Current per number of devices.
AL802ADA220J
(Current draw from battery) 1
Stand-by: 90mA 90mA
Alarm: 175mA 175mA
AAL802 Current 90mA 175mA
Auxiliary Devices Refer to device manual for current ratings.
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
BAuxiliary Devices Current (must not exceed 1A)
Refer to device manual for current ratings.
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
CNotification Appliances Current must not exceed 8A (8000mA) 0mA mA
DTotal alarm current mA mA
ETotal current ratings converted to amperes (line D x 0.001) A A
FNumber of standby hours (24 for NFPA 72, Chapter 1, 1-5.2.5). H
GMultiply lines E and F. Total stand-by AH AH
HAlarm sounding period in hours.
(For example, 5 minutes = 0.0833 hours.) H
IMultiply lines E and H. Total alarm AH AH
JAdd lines G and I. Total stand-by and alarm AH AH
K
Multiply line J by 1.30.
(30% extra insurance to meet desired performance)
Total ampere - hours required
AH
Units are capable of recharging 40AH battery max. If total ampere - hour required exceeds 40AH,
decrease AUX current to provide enough stand-by time for the application.

- 8 - AL802ADA220J
Hookup Diagram:
These circuits are used to monitor AC and Bat Fail and will cause a simultaneous trouble condition to the FACP's IN1 and IN2
Digital Communicator or Local Annunciator Dry output Contact (Form "C" contacts)
4-wire Smoke
Detector
+
–
+
–
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
from
FACP
SW1
– DC +
SW2
+ OUT1 –
OUT1 OUT2 OUT3 OUT4
INP1 INP2
FAULT
NC CNOC"FAULT" NC
OUT1 OUT3 OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
IN1+ IN1– IN2–
IN2+ C "DRY1" NC
RET1+ RET1– RET2–
RET2+ C "DRY2" NC
+ OUT2 – + OUT3 – + OUT4 –
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
– AUX +
UPPER TERMINALS
LOWER TERMINALS
Addressable Control Module Trigger Output See Note 2
line
neutral Use separate knockout.
Keep 0.25" spacing from
non power-limited wiring
Power-Limited Outputs
2.5A per
output in alarm
(total= 8A)
(Supervised)
Supervised Non-Supervised
Non-Supervised
Non-Supervised
RESET
Unswitched 220VAC
power mains
(non power-limited) NC C NO NC C NO NC C NO
AC Local
AC DELAY
BAT FAIL AC FAIL
AC LED
VR1
ON
1
ON
1
Fig. 2
These circuits are used to monitor AC and Bat Fail and will cause a simultaneous trouble condition to the FACP's IN1 and IN2
Digital Communicator or Local Annunciator Dry output Contact (Form "C" contacts)
4-wire Smoke
Detector
+
–
+
–
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
from
FACP
SW1
– DC +
SW2
+ OUT1 –
OUT1 OUT2 OUT3 OUT4
INP1 INP2
FAULT
NC CNOC"FAULT" NC
OUT1 OUT3 OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
IN1+ IN1– IN2–
IN2+ C "DRY1" NC
RET1+ RET1– RET2–
RET2+ C "DRY2" NC
+ OUT2 – + OUT3 – + OUT4 –
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
– AUX +
UPPER TERMINALS
LOWER TERMINALS
Addressable Control Module Trigger Output See Note 2
line
neutral Use separate knockout.
Keep 0.25" spacing from
non power-limited wiring
Power-Limited Outputs
2.5A per
output in alarm
(total= 8A)
(Supervised)
Supervised Non-Supervised
Non-Supervised
Non-Supervised
RESET
Unswitched 220VAC
power mains
(non power-limited) NC C NO NC C NO NC C NO
AC Local
AC DELAY
BAT FAIL AC FAIL
AC LED
VR1
ON
1
ON
1
NC CNOC"FAULT" NC
Fig. 2b
Fig. 2a
These circuits are used to monitor AC and Bat Fail and will cause a simultaneous trouble condition to the FACP's IN1 and IN2
Digital Communicator or Local Annunciator Dry output Contact (Form "C" contacts)
4-wire Smoke
Detector
+
–
+
–
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
from
FACP
SW1
– DC +
SW2
+ OUT1 –
OUT1 OUT2 OUT3 OUT4
INP1 INP2
FAULT
NC CNOC"FAULT" NC
OUT1 OUT3 OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
IN1+ IN1– IN2–
IN2+ C "DRY1" NC
RET1+ RET1– RET2–
RET2+ C "DRY2" NC
+ OUT2 – + OUT3 – + OUT4 –
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
– AUX +
UPPER TERMINALS
LOWER TERMINALS
Addressable Control Module Trigger Output See Note 2
line
neutral Use separate knockout.
Keep 0.25" spacing from
non power-limited wiring
Power-Limited Outputs
2.5A per
output in alarm
(total= 8A)
(Supervised)
Supervised Non-Supervised
Non-Supervised
Non-Supervised
RESET
Unswitched 220VAC
power mains
(non power-limited) NC C NO NC C NO NC C NO
AC Local
AC DELAY
BAT FAIL AC FAIL
AC LED
VR1
ON
1
ON
1
Fig. 2c Trouble Memory
Reset Button
Common trouble
Input/Output

AL802ADA220J - 9 -
Optional Hookups:
1- Battery and AC monitoring: AC or Battery Fail condition will cause the common trouble input
[C “FAULT” NC] to report back to the FACP via Input 1 and Input 2. The common trouble input may also
be used for other optional supervisory monitoring. (see Power Board Parameter for use of AC Delay, pg. 6)
To report AC and Battery Trouble connect the battery and AC Fail relay output shown in (Fig. 2a) to the
common trouble input.
2- Dry contact input [C “DRY1” NC] [C “DRY2” NC] can be used to alarm output from an addressable module
(these inputs are unidirection and cannot report back to trigger module).
Connection to triggering devices must be made within 20 ft. of distance and using conduit for wiring.
3- Auxiliary output [–AUX +] 24VDC at 1A max.
4- AC Local [NC, NO, C] should connect to the host control panel for local annunciation of the trouble condition.
Note: If common trouble input, terminals marked [C “FAULT” NC] are not used, these terminals must be
shorted (connect jumper) to remain inactive. For optional hookups see Fig. 2b.
Maintenance:
Unit should be tested at least once a year for the proper operation as follows:
Output Voltage Test: Under normal load conditions the DC output voltage should be checked for proper
voltage level (26.2-26.4VDC recommended range).
Battery Test: Under normal load conditions check that the battery is fully charged. Check specified
voltage both at the battery terminal and at the board terminals marked [+ BAT –] to
ensure that there is no break in the battery connection wires.
Fuses: Check input fuse on the power supply board, replace if necessary.
Input fuse rating is 5A @ 250V.
Note: Maximum charging current is 3.2A.
Note: Expected battery life is 5 years; however, it is recommended changing batteries in
4 years or less if needed.

- 10 - AL802ADA220J
Appendix A:
Compatible UL/cUL Listed Devices for Synchronization
A-1 Strobes, Horns, and Horn/Strobes
Table A-1 below lists Strobes, Horns, and Horn/Strobes compatible with AL802ADA220J NAC outputs.
Gentex:
GCS24CR - UL GCCB24PCR / W - UL GEC24-15/75WR - UL
GCS24CW - UL GCCG24PCR / W - UL GEC24-15/75WW - UL
GCS24PCR - UL GCCR24PCR / W - UL SSPK24CLPR - UL
GCS24PCW - UL WGESA24-75PWR / W - UL SSPK24CLPW - UL
GCC24CR - UL WGESB24-75PWR / W - UL SSPK24WLPR - UL
GCC24PCR - UL WGESG24-75PWR / W - UL SSPK24WLPW - UL
GCC24CW - UL WGESR24-75PWR / G - UL SSPK24AWR - UL
GCC24PCW - UL WGECA24-75PWR / W - UL SSPK24AWW - UL
GES3-24WR - UL WGECB24-75PWR / W - UL SSPK24-15/75WLPR - UL
GEC3-24WR - UL WGECG24-75PWR / W - UL SSPK24-15/75WLPW - UL
GEH24-R - UL WGECR24-75PWR / G - UL SSPK24-15/75AWR - UL
GEH24-W - UL WGESA24-75PWLPR / W - UL SSPK24-15/75AWW - UL
WGES24-75WR / WW - UL WGESB24-75PWLPR / W - UL SSPKA24-15/75PWR - UL
WGES24-75PWR / PWW - UL WGESG24-75PWLPR / W - UL SSPKA24-15/75PWW - UL
WGES24-75WRLP / WWLP - UL WGESR24-75PWLPR / W - UL SSPKA24-15/75AWR - UL
WGEC24-75WR / WW - UL WGECA24-75PWLPR / W - UL SSPKA24-15/75AWW - UL
WGEC24-75PWR / PWW - UL WGECB24-75PWLPR / W - UL SSPKB24-15/75PWR - UL
WGEC24-75WRLP / WWLP - UL WGECG24-75PWLPR / W - UL SSPKB24-15/75PWW - UL
WGEC24-75PWRLP / WWLP - UL WGECR24-75PWLPR / W - UL SSPKG24-15/75PWR - UL
GESA24PWR / W - UL GX91-R / W - UL/cUL SSPKG24-15/75PWW - UL
GESB24PWR / W - UL GX91-PR / W - UL/cUL SSPKR24-15/75PWR - UL
GESG24PWR / W - UL GX93-R / W - UL/cUL SSPKR24-15/75PWW - UL
GESR24PWR / W - UL GX93-PR / W - UL/cUL WSSPKA24-15/75AWR - UL
GECA24PWR / W - UL WSSPK24-15/75WR / WW - UL WSSPKA24-15/75AWW - UL
GECB24PWR / W - UL WSSPK24-15/75PWR / PWW - UL WSSPKA24-15/75PWR - UL
GECG24PWR / W - UL WSSPK24-15/75AWR / AWW - UL WSSPKA24-15/75PWW - UL
GECR24PWR / W - UL GES24-177WR - UL WSSPKB24-15/75PWR - UL
GCSA24PCR / W - UL GES24-177WW - UL WSSPKB24-15/75PWW - UL
GCSB24PCR / W - UL GES24-15/75WR - UL WSSPKG24-15/75PWR - UL
GCSG24PCR / W - UL GES24-15/75WW - UL WSSPKG24-15/75PWW - UL
GCSR24PCR / W - UL GEC24-177WR - UL WSSPKR24-15/75PWR - UL
GCCA24PCR / W - UL GEC24-177WW - UL WSSPKR24-15/75PWW - UL

AL802ADA220J - 11 -
Appendix A (cont’d):
Compatible UL/cUL Listed Devices for Synchronization
A-1 Strobes, Horns, and Horn/Strobes (cont’d)
Table A-1 below lists Strobes, Horns, and Horn/Strobes compatible with AL802ADA220J NAC outputs.
System Sensor:
CHSR - UL P4R-SP - UL PC4RH-P - UL SPSCW - UL SPSWK-CLR-ALERT-UL
CHSW - UL P4RH - UL PC4RH-SP - UL SPSCW-CLR-ALERT - UL SPSWK-P - UL
HR/HRK/HW - UL P4RH-P - UL PC4W - UL SPSCW-P - UL SPSWK-R - UL
MHR - UL P4RH-SP - UL PC4W-P - UL SPSCWH - UL SPSWV - UL
MHW - UL P4RK - UL PC4W-SP - UL SPSCWH-P - UL SPSWV-P - UL
P1224MC - UL P4RK-R - UL PC4WH - UL SPSCWHK - UL SR - UL
P2R - UL P4W - UL PC4WH-P - UL SPSCWHK-P - UL SR-P - UL
P2R-P - UL P4W-P - UL PC4WH-SP - UL SPSCWK - UL SR-SP - UL
P2R-SP - UL P4W-SP - UL PC4WHK - UL SPSCWK-CLR-ALERT - UL SRH - UL
P2RH - UL P4WH - UL PC4WK - UL SPSCWK-R - UL SRH-P - UL
P2RH-LF - UL P4WH-P - UL SCR - UL SPSCWV - UL SRH-SP - UL
P2RH-P - UL P4WH-SP - UL SCR-P - UL SPSCWV-P - UL SRHK - UL
P2RH-SP - UL P4WK - UL SCR-SP - UL SPSCWVH - UL SRHK-P - UL
P2RHK - UL PC2R - UL SCRH - UL SPSCWVH-P - UL SRHK-R - UL
P2RHK-P - UL PC2R-P - UL SCRH-P - UL SPSR - UL SRK - UL
P2RHK-R - UL PC2RH - UL SCRH-SP - UL SPSR-P - UL SRK-P - UL
P2RK - UL PC2RH-P - UL SCRHK - UL SPSRH - UL SRK-R - UL
P2RK-P - UL PC2RH-SP - UL SCRK - UL SPSRH-P - UL SW - UL
P2RK-R - UL PC2RHK - UL SCW - UL SPSRHK - UL SW-ALERT - UL
P2W - UL PC2RK - UL SCW-CLR-ALERT - UL SPSRK - UL SW-CLR-ALERT - UL
P2W-P - UL PC2W - UL SCW-P - UL SPSRK-P - UL SW-P - UL
P2W-SP - UL PC2W-P - UL SCW-SP - UL SPSRK-R - UL SW-SP - UL
P2WH - UL PC2W-SP - UL SCWH - UL SPSRV - UL SWH - UL
P2WH-LF - UL PC2WH - UL SCWH-P - UL SPSRV-P - UL SWH-ALERT - UL
P2WH-P - UL PC2WH-P - UL SCWH-SP - UL SPSW - UL SWH-P - UL
P2WH-SP - UL PC2WH-SP - UL SCWHK - UL SPSW-ALERT - UL SWH-SP - UL
P2WHK - UL PC2WHK - UL SCWK - UL SPSW-CLR-ALERT - UL SWHK - UL
P2WHK-P - UL PC2WK - UL SPSCR - UL SPSW-P - UL SWHK-P - UL
P2WK - UL PC4R - UL SPSCRH - UL SPSWH - UL SWK - UL
P2WK-P - UL PC4R-P - UL SPSCRV - UL SPSWH-P - UL SWK-P - UL
P4R - UL PC4R-SP - UL SPSCRVH - UL SPSWK - UL
P4R-P - UL PC4RH - UL
Potter/Amseco:
CM24CR - UL CSL-1224W-BW - UL/cUL MH-12/24W - UL/cUL SSC8-177R - UL
CM24CW - UL CSL-1224W-GR - UL/cUL SCM24C-177R - UL SSC8-177W - UL
CSH-1224W-AR - UL/cUL CSL-1224W-GW - UL/cUL SCM24C-177W - UL SSC8-3075110R - UL
CSH-1224W-AW - UL/cUL CSL-1224W-RR - UL/cUL SCM24C-3075110R - UL SSC8-3075110W - UL
CSH-1224W-BR - UL/cUL CSL-1224W-RW - UL/cUL SCM24C-3075110W - UL SSR2-177R - UL
CSH-1224W-BW - UL/cUL CSL24CAW - UL/cUL SH-1224R - UL/cUL SSR2-177W - UL
CSH-1224W-GR - UL/cUL CSL24C-BW - UL/cUL SH-1224W - UL/cUL SSR2-3075110R - UL
CSH-1224W-GW - UL/cUL CSL24C-GW - UL/cUL SH-1224WP-R - UL/cUL SSR2-3075110W - UL
CSH-1224W-RR - UL/cUL CSL24C-RW - UL/cUL SH-1224WP-W - UL/cUL SSR8-177R - UL
CSH-1224W-RW - UL/cUL CSL24C-AR - UL/cUL SH24C-177R - UL/cUL SSR8-177W - UL
CSH24C-AW - UL/cUL CSL24C-BR - UL/cUL SH24C-177W - UL/cUL SSR8-3075110R - UL
CSH24C-BW - UL/cUL CSL24C-GR - UL/cUL SL-1224R - UL/cUL SSR8-3075110W - UL
CSH24C-GW - UL/cUL CSL24C-RR - UL/cUL SL-1224W - UL/cUL SSS2-1530R - UL
CSH24C-RW - UL/cUL H-1224R - UL/cUL SL-1224WP-R - UL/cUL SSS2-1530W - UL
CSH24C-AR - UL/cUL H-1224W - UL/cUL SL-1224WP-W - UL/cUL SSS2-75110R - UL
CSH24C-BR - UL/cUL HP-25TR - UL/cUL SL-24W - UL/cUL SSS2-75110W - UL
CSH24C-GR - UL/cUL HP-25TW - UL/cUL SSC2-177R - UL SSS8-1530R - UL
CSH24C-RR - UL/cUL MH-12/24R - UL/cUL SSC2-177W - UL SSS8-1530W - UL
CSL-1224W-AR - UL/cUL MH-12/24TR - UL/cUL SSC2-3075110R - UL SSS8-75110R - UL
CSL-1224W-AW - UL/cUL MH-12/24TW - UL/cUL SSC2-3075110W - UL SSS8-75110W - UL
CSL-1224W-BR - UL/cUL

- 12 - AL802ADA220J
Appendix A (cont’d):
Compatible UL/cUL Listed Devices for Synchronization
A-1 Strobes, Horns, and Horn/Strobes (cont’d)
Table A-1 below lists Strobes, Horns, and Horn/Strobes compatible with AL802ADA220J NAC outputs.
Cooper/Wheelock:
50-241575W-FR - UL/cUL E70-24MCW-FN - UL/cUL ET90-24MCCH-FN - UL/cUL LSTW-A* - UL/cUL
AH-24WP-R - UL E70-24MCW-FR - UL/cUL ET90-24MCCH-FW - UL/cUL LSTW-ALA* - UL/cUL
AMT-12/24-R - UL/cUL E70-24MCW-FW - UL/cUL HNR - UL/cUL LSTW-NA* - UL/cUL
AMT-12/24-W - UL/cUL E70-24MCWH-FN - UL/cUL HNRC - UL/cUL LSTW-NA* - UL/cUL
AMT-241575W-FR - UL/cUL E70-24MCWH-FR - UL/cUL HNW - UL/cUL MIZ-24S-R - UL/cUL
AMT-241575W-FR-NYC - UL E70-24MCWH-FR - UL/cUL HNWC - UL/cUL MIZ-24S-W - UL/cUL
AMT-241575W-FW - UL/cUL E70-24MCWH-FW - UL/cUL HS-24-R - UL/cUL MT-12/24-R - UL
AMT-24MCW-FR - UL/cUL E70H-241575W-FR - UL/cUL HS-24-W - UL/cUL MT-241575W-FR - UL/cUL
AMT-24MCW-FW - UL/cUL E70H-241575W-FW - UL/cUL HS4-241575W-FR - UL/cUL MT-241575W-FW - UL/cUL
AS-12100C - UL/cUL E70H-24MCW-FR - UL/cUL HS4-24MCC-FR - UL MT-24MCW-FR - UL/cUL
AS-24100C - UL/cUL E70H-24MCW-FW - UL/cUL HS4-24MCC-FW - UL/cUL MT-24MCW-FW - UL/cUL
ASWP-2475C-FR - UL E70H-24MCWH-FN - UL/cUL HS4-24MCW-FR - UL/cUL MTWP-2475C-FR - UL
ASWP-2475C-FW - UL E70H-24MCWH-FW - UL/cUL HS4-24MCW-FW - UL/cUL MTWP-2475C-FW - UL
ASWP-2475W-FR - UL E90-24MCC-FN - UL/cUL HSR - UL/cUL MTWP-2475W-FR - UL
ASWP-2475W-FW - UL ET90-24MCC-FW - UL/cUL HSRC - UL/cUL MTWP-2475W-FW - UL
ASWP-24MCCH-FR - UL ET90-24MCC-FN - UL/cUL HSW - UL/cUL MTWP-24MCCH-FR - UL
ASWP-24MCCH-FW - UL E90-24MCC-FR - UL/cUL HSWC - UL/cUL MTWP-24MCCH-FW - UL
ASWP-24MCWH-FR - UL E90-24MCC-FW - UL/cUL LHNR* - UL/cUL MTWP-24MCWH-FR - UL
ASWP-24MCWH-FW - UL E90-24MCCH-FN - UL/cUL LHNW* - UL/cUL MTWP-24MCWH-FW - UL
CH70-24MCW-FR - UL/cUL E90-24MCCH-FR - UL/cUL LHSR* - UL/cUL RSS-241575W-FR - UL/cUL
CH70-24MCW-FW - UL/cUL E90-24MCCH-FW - UL/cUL LHSR-A* - UL/cUL RSS-241575W-FW - UL/cUL
CH70-24MCWH-FR - UL/cUL E90H-24MCC-FR - UL/cUL LHSR-AL* - UL/cUL RSS-24MCW-FR - UL/cUL
CH70-24MCWH-FW - UL/cUL E90H-24MCC-FW - UL/cUL LHSR-N* - UL/cUL RSS-24MCW-FW - UL/cUL
CH90-24MCC-FR - UL/cUL E90H-24MCCH-FR - UL/cUL LHSW* - UL/cUL RSS-24MCWH-FR - UL/cUL
CH90-24MCC-FW - UL/cUL E90H-24MCCH-FW - UL/cUL LHSW-A* - UL/cUL RSS-24MCWH-FW - UL/cUL
CH90-24MCCH-FR - UL/cUL EET90-24MCCH-FR - UL/cUL LHSW-AL* - UL/cUL RSSA-24MCC-NW - UL
CH90-24MCCH-FW - UL/cUL ET-1010-R - UL LHSW-N* - UL/cUL RSSA-24MCCH-NW - UL
E50-241575W-FW - UL/cUL ET-1010-W - UL LSPSTR* - UL/cUL RSSB-24MCC-NW - UL
E50-24MCWH-FR - UL/cUL ET70-241575W-FR - UL/cUL LSPSTR-AL* - UL/cUL RSSB-24MCCH-NW - UL
E50-24MCWH-FW - UL/cUL ET70-241575W-FW - UL/cUL LSPSTR-ALA* - UL/cUL RSSG-24MCC-NW - UL
E50H-241575W-FR - UL/cUL ET70-24MCW-FN - UL/cUL LSPSTR-N* - UL/cUL RSSG-24MCCH-NW - UL
E50H-241575W-FW - UL/cUL ET70-24MCW-FR - UL/cUL LSPSTR-NA* - UL/cUL RSSR-24MCC-NW - UL
E50H-24MCW-FR - UL/cUL ET70-24MCW-FW - UL/cUL LSPSTW* - UL/cUL RSSR-24MCCH-NW - UL
E50H-24MCW-FW - UL/cUL ET70-24MCWH-FN - UL/cUL LSPSTW-AL* - UL/cUL RSSWP-2475C-FR - UL
E50H-24MCWH-FR - UL/cUL ET70-24MCWH-FR - UL/cUL LSPSTW-ALA* - UL/cUL RSSWP-2475C-FW - UL
E50H-24MCWH-FW - UL/cUL ET70-24MCWH-FW - UL/cUL LSPSTW-N* - UL/cUL RSSWP-2475W-AR - UL
E60-24MCC-FR - UL/cUL ET70WP-24185W-FR - UL LSPSTW-NA* - UL/cUL RSSWP-2475W-FR - UL
E60-24MCC-FW - UL/cUL ET70WP-24185W-FW - UL LSTR* - UL/cUL RSSWP-2475W-FW - UL
E60-24MCCH-FR - UL/cUL ET70WP-2475C-FR - UL LSTR-A* - UL/cUL RSSWP-2475W-NW - UL
E60-24MCCH-FW - UL/cUL ET70WP-2475C-FW - UL LSTR-AL* - UL/cUL RSSWP-24MCCH-FR - UL
E60H-24MCC-FR - UL/cUL ET80-24MCW-FR - UL/cUL LSTR-ALA* - UL/cUL RSSWP-24MCCH-FW - UL
E60H-24MCC-FW - UL/cUL ET80-24MCW-FW - UL/cUL LSTR-NA* - UL/cUL RSSWP-24MCWH-FR - UL
E60H-24MCCH-FR - UL/cUL ET80-24MCWH-FR - UL/cUL LSTRW-ALA* - UL/cUL RSSWP-24MCWH-FW - UL
E60H-24MCCH-FW - UL/cUL ET80-24MCWH-FW - UL/cUL LSTW* - UL/cUL S8-24MCC-FW - UL/cUL
S8-24MCCH-FW - UL/cUL STH-3R24MCCH-NR - UL STR-ALB - UL STW-ALB - UL
SA-S70-24MCW-FR - UL STH-4M30WC - UL STR-NA - UL STW-NA - UL
SA-S70-24MCW-FW - UL STH-4MS-R - UL STR-NB - UL STW-NB - UL
SA-S90-24MCC-FR - UL STH-4R - UL STR-NG - UL STW-NG - UL
SA-S90-24MCC-FW - UL STH-4R24MCCH-NW - UL STR-NR - UL STW-NR - UL
STH-2G - UL STH-4R24MCCH110B-NR - UL STRC-NA - UL STWC-AB - UL
STH-2MS-R - UL STH-4R24MCCH110R-NA - UL STRC-NB - UL STWC-ALA - UL
STH-2R - UL STH-4R24MCCH110R-NR - UL STRC-NG - UL STWC-ALB - UL
STH-2R24MCCH-NR - UL STH-90-4R24MCCH-NW - UL STRC-NR - UL STWC-NA - UL
STH-3MS-R - UL STR-AB - UL STW-AB - UL STWC-NB - UL
STH-3R - UL STR-ALA - UL STW-ALA - UL STWC-NG - UL
STWC-NR - UL
*When using these model strobes the maximum current per NAC is limited to 2A.

AL802ADA220J - 13 -
Appendix B - UL Listed Compatible Devices
B.1 Four (4) Wire Smoke Detectors
Table B-1 below lists four (4) wire smoke detectors compatible with AL802ADA220J AUX output and
Outputs 1-8 when programmed as AUX.
System Sensor
Smoke Detector/Base Detector Type Max Stand-by
Current (mA)
Alarm
Current (mA)
B112LP Base 0.12 36
B114LP Base * *
B404B Base * *
DH100ACDC Photoelectric 0.15 0.70
DH100ACDCLP Photoelectric 0.15 0.70
DH100ACDCLPW Photoelectric 0.15 0.70
DH400ACDCI Ionization Duct 25 95
DH400ACDCP Photoelectric Duct 25 95
1112/24/D Ionization 0.05 50
1424 Ionization 0.10 41
1451 (w/B402B Base) Ionization 0.10 39
2112/24ATR Photoelectric 0.50 60/70
2112/24AITR Photoelectric 0.50 60/70
2112/24/D Photoelectric 0.05 50
2112/24R Photoelectric 0.50 60/70
2112/24TR Photoelectric 0.50 60/70
2112/24T/D Photoelectric w/135oThermal 0.05 50
2112/24TSRB Photoelectric w/135o Thermal Supervisory Relay 15 45
2312/24TB Photoelectric 0.12 50
2412 (12 volt) Photoelectric 0.12 77
2412AT (12 volt) Photoelectric 0.12 58
2412TH (12 volt) Photoelectric 0.12 77
2424 Photoelectric 0.10 41
2424TH Photoelectric 0.10 41
2451 Photoelectric 0.10 39
2451TH (with/B402B Base) Photoelectric 0.10 39
2W-MOD Loop Test/Maintenance Mod. 30 50
4W-B (12/24 volt) Photoelectric I30.05 23
4WT-B (12/24 volt) Photoelectric I3w/Therm 0.05 23
4WTA-B (12/24 volt) I3 Photo w/Therm/Sounder 0.05 35
4WTR-B (12/24 volt) I3 Photo w/Therm/Relay 0.05 35
4WTR-B (12/24 volt) I3 Photo w/Therm/Sounder/Relay 0.05 50
4WITAR-B (12/24 volt) I3 Photo w/Isolated Therm/Sounder/Relay 0.05 50
2W-MOD2 I3 Loop Test/Maintenance Mod. 0.05 *
RRS-MOD I3 Reversing Relay/Sync Module 0.05 *
6424 Projected Beam 10 28.4
Beam 1224(S) Projected Beam 17 38.5
* Contact manufacturer for current draws.
B.2 Relays
Table B-3 below lists relays compatible with AL802ADA220J AUX output and Outputs 1-8 when programmed
as AUX.
Manufacturer Model Current (mA) Manufacturer Model Current (mA)
System
Sensor
PR-1 15
System
Sensor
R-20T 40
PR-2 30 R-24T 40
PR-3 30 R-10E 23
EOLR-1 30 R-14E 23
R-10T 23 R-20E 40
R-14T 23 R-24E 40

- 14 - AL802ADA220J
Notes:

AL802ADA220J - 15 -
Notes:

- 16 - AL802ADA220J
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
IIAL802ADA220J F27R MEMBER
1.5”
(38.1mm)
1.0”
(25.4mm)
4.5”
(114.3mm)
1.0”
(25.4mm)
1.0”
(25.4mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.0”
(25.4mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
8.5”
(215.9mm)
18.0”
(457.2mm)
18.0”
(457.2mm)
18.0”
(457.2mm)
6.0”
(152.4mm)
2.5”
(63.5mm)
2.75”
(69.85mm)
2.75”
(69.85mm)
4.5”
(114.3mm)
4.5”
(114.3mm)
14.5”
(368.3mm)
14.5”
(
368.3mm
)
1.0”
(25.4mm)
1.0”
(25.4mm)
14.5”
(368.3mm)
2.5”
(63.5mm)
1.5”
(38.1mm)
2.5”
(63.5mm)
Enclosure Dimensions (H x W x D approximate):
18” x 14.5” x 4.5” (457.2mm x 368.3mm x 114.3mm)