Altronix AL602ULADA User manual
Rev. 042209
AL602ULADA
NAC Power Extender
Installation Guide
(see 02 Application Guide for additional information)
Altronix Corp.
140 58th St. Brooklyn,NY
- 2 - AL602ULADA
Agency Listings:
• ULListedControlUnitsandAccessoriesfor
FireSystems(UL864).
• MEA-NYCDepartmentofBuildingsApproved.
• CSFM-CaliforniaStateFireMarshalApproved.
• FM-FactoryMutualApproved.
• NFPA72Compliant.
Input:
• Powerinput120VAC60Hz,4amp.
• Two(2)ClassA,StyleZortwo(2)ClassB,
StyleW,X,YFACPinputs.
• Two(2)NCdrycontacttriggerinputs.
Output:
• 24VDC@6.5ampmaxtotalalarmcurrent.
• 2.5ampmaxcurrentperoutput.
• Separate1.0ampauxiliaryoutput.
• Two(2)outputsmaybeparalleledformorepoweronan
indicatingcircuit(see 02 Application Guide).
• Programmablesupervisedindicatingcircuitoutputs:
Four(4)ClassB,StyleW,X,YorTwo(2)ClassA,
StyleZorOne(1)ClassA,StyleZandTwo(2)ClassB,
StyleW,X,Y(see 02 Application Guide).
•Thermalandshortcircuitprotectionwithautoreset.
Battery Backup:
• Chargingvoltageis26.2-26.4VDC.
•Built-inchargerforsealedleadacidorgeltypebatteries.
•Automaticswitchovertostand-bybatterywhenACFails.
• Zerovoltagedropwhenswitchingovertobatterybackup.
Supervision:
•ACfailsupervision(form“C”contact,1amp/28VDC).
Factorysetfor30secondswithoptional2.5to3hour
delaysetting(fieldselectable).
Supervision (cont’d):
• InstantlocalACtroublereportingrelay
(form“C”contact,1amp/28VDC).
•Batterypresenceandlowbatterysupervision
(form“C”contact,1amp/28VDC).
Visual Indicators:
•InputandoutputstatusLEDindicators.
Special Features:
• 2-wirehorn/strobeSyncmodeallowsaudible
notificationappliances(horns)tobesilenced
whilevisualnotificationappliances(strobes)
continuetooperate.
• SyncprotocolsincludePotter/Amseco,Faraday,
Gentex®,SystemSensor®,andCooperWheelock®.
• TemporalCode3,SteadyMode,InputtoOutput
FollowerMode(maintainssynchronizationof
notificationappliancescircuit).
• Compatiblewith12VDCor24VDCfirepanels.
•Outputloopsupervisionsteeredtoinput1orinput2.
• Signalcircuittroublememory(helpsidentify
intermittentloopproblems).
• Commontroubleinputandoutputforexternaltrouble
signalstie-in.
• Groundfaultdetection.
•Unitincludespowersupply,redenclosure,camlock,
andbatteryleads.
Enclosure Dimensions (approx. H x W x D):
15.5”x12”x4.5”(393.7mmx304.8mmx114.3mm).
Overview:
TheAltronixAL602ULADAisanextremelycosteffective6.5ampremotepowersupply/batterycharger.Itmaybe
connectedtoany24voltFireAlarmControlPanel(FACP).PrimaryapplicationsincludeNotificationApplianceCircuit
(NACsuchasstrobesandhorns)expansionsupporttomeetADArequirements.Italsoprovidesauxiliarypowertosupport
systemaccessories.Theunitdeliverselectronicallyregulatedandfiltered24voltpowertoClassB,StyleW,X,YorClass
A,StyleZNACloopcircuits.Additionally,aseparate1.0Aauxiliaryoutputforfour(4)-wiresmokedetectorsisavailable.
The6.5ampmax.alarmcurrentcanbedividedbetweenthefour(4)outputsforpoweringNACdevices.Eachoutputis
ratedat2.5ampmax.,andcanbeindependentlyprogrammedforSteady,TemporalCode3orStrobeSynchronization.
AlloutputsmaybeprogrammedforInputtoOutputFollowerMode(outputwillfollowinput).Anindividualoutputof4
ampisachievedbyparalleling2outputs.Innon-alarmconditionindependentloopsupervisionforClassA,StyleZand/
orClassB,StyleW,X,YFACPNACcircuitsisprovided.Intheeventofalooptrouble,theFACPwillbenotifiedvia
thesteeredinput(input1orinput2).Inaddition,therearecommontroubleoutputterminals(NC,C,NO)whichareused
toindicategeneralloop/systemtrouble.AcommontroubleinputisprovidedforoptionalNC(normallyclosed)devices
toreporttroubletotheFACP.Two(2)FACPsignalingoutputscanbeemployedanddirectedtocontrolsupervisionand
powerdeliverytoanycombinationofthefour(4)outputs.
Specifications:
AL602ULADA - NAC Power Extender
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.
AL602ULADA - 3 -
Power Supply Specifications:
AC Input: 120VAC60Hz,4amp.
Output:
Four(4)regulatedsupervisedNACoutputcircuits,24VDC,2.5ampmaximumcurrent.
One(1)aux.specialapplication24VDCpoweroutputcircuit1amp,non-supervised
totaloutputcurrentmustnotexceedcurrent6.5ampinAlarmCondition.
Battery Usetwo(2)12VDC/7AH,two(2)12VDC/12AHortwo(2)12VDC/40AH
batteriesconnectedinseries.
Stand-by/Alarm Current
Consumption: 90mA/175mA
EOL Resistor (end of line): 2.2K(2200ohm),AltronixModel#AL-EOL22(included).
Ground fault maximum
test impedance: 1000ohm.
Stand-by Specifications:
Stand-by Batteries Stand-by Time Total Amp/Minutes Alarm Output Current
Aux.
Output
24VDC/7AH 24Hours 6.5amp/5minutes ---
24VDC/12AH
(usetwo(2)12VDCbatteriesinseries) 24Hours 6.5amp/5minutes 50mA
24VDC/40AH 24Hours 6.5amp/5minutes 1amp
Note: Unit is equipped with 1 amp max. auxiliary output: “AUX” will remain battery backed up during power
outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” above for ratings. When
loads are connected to “AUX” output during alarm condition, the remaining outputs may not exceed 6.5 amp
total alarm current (example: AUX = 1 amp, outputs up to 5.5 amp).
Installation Instructions:
WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/NFPA72/
ANSI,andwithalllocalcodesandauthoritieshavingjurisdiction.
Productisintendedforindoordryuseonly.
Carefully review:
Application Guide for AL602ULADA, AL802ULADA, AL1002ULADA
Power Supply Specifications (pg. 3)
Stand-by Specifications (pg. 3)
Output Programming Selection Table (pg. 4)
Sync Mode Selection Table (pg. 4)
Terminal Identification Table (pgs. 5-6)
LED Status Indication Table (pg. 6)
1.Mounttheunitinthedesiredlocation.Markandpredrillholesinthewalltolineupwiththetoptwokeyholesinthe
enclosure.Installtwoupperfastenersandscrewsinthewallwiththescrewheadsprotruding.Placetheenclosure’s
upperkeyholesoverthetwoupperscrews;levelandsecure.Markthepositionofthelowertwoholes.Removethe
enclosure.Drillthelowerholesandinstalltwofasteners.Placetheenclosure’supperkeyholesoverthetwoupper
screws.Installthetwolowerscrewsandmakesuretotightenallscrews(Enclosure Dimensions, pg. 12).
Secureenclosuretoearthground(Fig. 1, pg. 3). Smallterminalblockwiregaugesrangefrom
16AWGto24AWG,allothersrangefrom14AWGto24AWG.
2.Connecttheline(L)andneutral(N)terminalstoaseparateunswitchedACcircuit(120VAC,60Hz)
dedicatedtotheFireAlarmSystem.
3.Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.
4. Connectbatterytotheterminalsmarked[+BAT--]onthePowerSupplyBoard(batteryleadsincluded).
Usetwo(2)12VDCbatteriesconnectedinseries.
5. Setoutputselectionswitchesmarked[OUT1throughOUT4]tofollowcorrespondinginput[IN1&IN2]and
desiredoutputsignaltype (Output Programming Selection Table, pg. 4).
6. ConnectFACPoutputtothedesiredAL800LGK9Elogicboardinputs,andnotificationappliancestothedesired
AL800LGK9Elogicboardoutputs(see 02 Application Guide).
Fig. 1
L N
line
ground
neutral
- 4 - AL602ULADA
Note:The2-wirehorn/strobesyncmodewillonlysynchronizehorns,horn/strobes,strobeswith
synchronizationcapability.
7. Forconnectionofsmokedetectors,digitaldialer(see Hookup Diagram, pg. 7).
Class A, Style Z Class B, Style W, X, Y, SW1 & SW2 Settings:
• ForallClassB,StyleW,X,Y,hookupsSW1&SW2ontheAL800LGK9Elogicboardmustbeopen.
ForallClassA,StyleZhookupsSW1&SW2ontheAL800LGK9Elogicboardmustbeclosed.
Output Programming Selection Table:
Outputs must be programmed independently (OUT1 - OUT4)
Function Switch Positions Descriptions
ON OFF
InputtoOutputFollower
Mode
1 2,3 Outputfollowssignalitreceivesfromthecorrespondinginput(i.e.
FACPSyncmodule-maintainssynchronizationof
notificationappliancecircuit).
TemporalCode3Mode 3 1,2 EnablesTemporalCode3signalgenerationoutput.
Thismodewillacceptasteadyorapulsinginput.
SteadyMode 1,2,3 Asteadyoutputsignalwillbegenerated.
Thismodewillacceptsteadyorpulsinginput.
For the above modes Dip Switch 4 determines which Input controls
the corresponding output:
Switch 4 in the ON position causes output(s) to be controlled by input 1.
Switch 4 in the OFF position causes output(s) to be controlled by input 2.
Note: It is required to control visual notification appliances (strobes) via input 1 (IN1)
and audible notification appliances (horns) via input 2 (IN2). This allows audible
notification appliances (horns) to be silenced while visual notification appliances (strobes) continue to operate. The
FACP must be capable of a visual annunciation to the silencing status of the output or zone(s) to which the
AL602ULADA (NAC Power Extender) is connected.
Sync Mode Selection Table:
Function Switch Positions Descriptions
ON OFF
AmsecoSync
Mode*
1,3,
42
ThismodeisdesignedtoworkwiththeAmsecoseriesofhorns,strobes,and
horn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,
synchronizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/
strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
Faraday
SyncMode* 2,4 1,3
ThismodeisdesignedtoworkwiththeFaradayseriesofhorns,strobes,andhorn/
strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchro-
nizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobe
combinationoveratwo-wirecircuitwhileleavingstrobesactive.
Gentex®
SyncMode*
Gentexisaregisteredtrademark
ofGentexCorporation.
1,2,
3,4
ThismodeisdesignedtoworkwiththeGentex®seriesofhorns,strobes,andhorn/
strobestoprovideameansofsynchronizingtheTemporal-codedhorns,synchro-
nizingtheflashtimingofthestrobe,andsilencingthehornsofthehorn/strobe
combinationoveratwo-wirecircuitwhileleavingstrobesactive.
SystemSensor®
SyncMode*
SystemSensorisaregistered
trademarkofHoneywell.
1,2,4 3
ThismodeisdesignedtoworkwiththeSystemSensor®seriesofhorns,strobes,
andhorn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,
synchronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsof
thehorn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
CooperWheelock®
SyncMode*
CooperWheelockisa
registeredtrademarkof
CooperWheelock.
2,3,4 1
ThismodeisdesignedtoworkwiththeCooperWheelockseriesofhorns,strobes,
andhorn/strobestoprovideameansofsynchronizingtheTemporal-codedhorns,
synchronizingtheone-secondflashtimingofthestrobe,andsilencingthehornsof
thehorn/strobecombinationoveratwo-wirecircuitwhileleavingstrobesactive.
(AL800LGK9E Board)
Output Dip Switches
INPUT SELECT
TEMPORAL
STROBE SYNC
IN>OUT SYNC
*Note:TheAL602ULADAwillonlysynchronizehorns,horn/strobesandstrobesthatcontainsynchronizationcapability.
Contactsignalmanufacturerformoredetailedinfo(see Appendix A.4, pg. 12).Thesamesynchronizationmodemustbe
selectedforalloutputs
Amount of Notification Appliances per NAC:
Amseco 27perNAC* SystemSensor® 32perNAC*
Faraday 39perNAC* CooperWheelock® 32perNAC*
Gentex® 32perNAC*
*Not to exceed a maximum of 2.5 amp per NAC.
Terminal Identification Table:
AL800LGK9E Logic Board
Terminal
Legend
Function/Description
IN1+,IN1-
IN2+,IN2-
(Supervised)
Theseterminalsconnecttothe24VDCFACPnotificationappliancecircuitoutputs.
(ClassA,StyleZorClassB,StyleW,X,Y)Inputtriggervoltageis8-33VDC@5mAmin.
Terminalpolarityisshowninalarmcondition.Duringanalarmconditiontheseinputswillcause
theselectedoutputschosentodrivenotificationappliances.Thedesignatedoutputsaresetbyoutput
switches[OUT1throughOUT4](Output Programming Selection Table, pg. 4). Atroubleconditionon
anoutputloopwillcausethecorrespondinginputtotriptheFACPbyopeningtheFACPloop.An
alarmconditionwillalwaysoverridetroubletodrivenotificationappliances.
RET1+,RET1-
RET2+,RET2-
(Supervised)
For(ClassA,StyleZhookupstheseterminalpairsreturntoFACPNAC1and/orNAC2.For
ClassB,StyleW,X,YhookupstheFACPEOLresistorfromtheNAC1and/orNAC2outputsare
terminatedattheseterminals.
C“DRY1”NC
C“DRY2”NC
(Dryinputtrigger)
Anopenacrosstheseinputs,willcausetheselectedoutputschosentodrivenotificationappli-
ances.Thedesignatedoutputsaresetbyoutputswitches[OUT1throughOUT4](Output
Programming Selection Table, pg. 4).Notetheseinputsareunidirectionalandwillnotreporta
troubleconditiontotheFACP.
+OUT1--
+OUT2--
+OUT3--
+OUT4--
(Supervised)
Notificationappliancesareconnectedtotheseregulatedoutputs (see 02 Application Guide pg.
2-4). Eachpower-limitedoutputwillsupply2.5amp.Two(2)outputsmaybeconnectedinparallel
foramaximumNACoutputcapabilityof4amp.Totalsupplycurrentis6.5amp(see note below).
Outputsarecontrolledbydesignatedinput1[IN1]orinput2[IN2](Output Programming Selection
C“FAULT”NC
(Common
troubleinput)
Anopencircuitacrossthispairofterminalswillcause[IN1andIN2]tosimultaneouslysignala
troubleconditionbacktotheFACP(TypicallyusedtoreportACorBATFail).(form“C”contact
1amp/28VDC)(Fig. 2, pg. 7).
NC,C,NO
(Common
troubleoutput)
Thesearedrycontacttroubleoutputsthatfollowanygeneralloop/systemtroubleconditions.
(Typicallyusedtotriggeradigitalcommunicatororotherreportingdevice).
(form“C”contact1amp/28VDC0.35PowerFactor)(Fig. 2, pg. 7) .
--AUX+ Thisseparate1ampmaxauxiliarySpecialApplicationPoweroutputcircuitistypicallyusedto
power4-wiresmokedetectors.Seeattachedlistofdevices(Appendix A, pgs. 10-12).
+DC-- 24VDCfrompowersupply.
Note: Unit is equipped with 1 amp max. auxiliary output: “AUX” will remain battery backed up during power
outage. For loads connected to “AUX” please refer to battery “Stand-by Specifications” pg. 3 for ratings. When
loads are connected to “AUX” output during alarm condition, the remaining outputs may not exceed 6.5 amp
total alarm current (example: AUX = 1 amp, outputs up to 5.5 amp).
AL602ULADA - 5 -
- 6 - AL602ULADA
Terminal Identification Table:
AL600ADA Power Supply Board*
Terminal
Legend Function/Description
L,G,N Connect120VACtotheseterminals:Ltohot,Ntoneutral.
-DC+ 24VDC@6.5ampinalarmnonpower-limitedoutput.
ACFAIL
NO,C,NC
Form“C”drycontactsusedtoinstantaneouslysignalthelossACtolocalannunciation
devices,withACpresentterminalsmarkedNOandCareopen,NCandCareclosed.
WhenlossofACoccursterminalsmarkedNOandCareclosed,NCandCareopen.
ACLOCAL
NC,NO,C
Form“C”drycontactsusedtoinstantaneouslysignalthelossACtolocalannunciationdevices,with
ACpresentterminalsmarkedNOandCareopen,NCandCareclosed.WhenlossofACoccurstermi-
nalsmarkedNOandCareclosed,NCandCareopen.
BATFAIL
NO,C,NC
Form“C”drycontactsusedtosignallowbatteryvoltageorlossofbatteryvoltage.Undernormal
conditionsterminalsmarkedNOandCareopen,NCandCareclosed.Duringatroubleconditionter-
minalsmarkedNOandCareclosed,andNCandCareopen(Fig. 2, pg. 7).
+BAT- Stand-bybatteryinput(leadsprovided)(Fig. 2, pg. 7).
*Power Board Parameter Specifications:
• ACFailconditionwillreportapproximately30secondsafterlossofAC.Todelayreportfor2.5to3hourscut
jumperACDELAYonthePowerSupplyBoard(ACtroubleoutputdelayoption).IfthismodeisselectedthePower
SupplyBoardmustberesetbyremovingallpowertoitfor30seconds.
• Lowbatteryconditionwillreportatapproximately21VDC.
• Batterypresencedetectionwillreportwithin180secondsafterbatteryremainsundetected(missingorremoved).
Arestoredbatterywillreportwithin30seconds.
LED Diagnostics:
AL600ADA - Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normaloperatingcondition.
ON OFF LossofAC,Stand-bybatterysupplyingpower.
OFF ON NoDCoutput.
OFF OFF LossofAC.Dischargedornostand-bybattery.NoDCoutput.
AL800LGK9E - Logic Board
LED OFF ON BLINK (LONG)* BLINK (SHORT)**
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
Input1 Normal AlarmCondition TroubleCondition ---
Input2 Normal AlarmCondition TroubleCondition ---
Fault Normal AlarmCondition --- ---
* Indicatescurrenttroublecondition.Whentrouble(open,shortorground)occursonaspecificoutput,the
correspondingredoutputLED,[OUT1-OUT4]willblink.ThecorrespondinggreeninputLEDwill
blinkaswell.Looptroublewillreportwithin30seconds.
**Indicatestroubleconditionmemory.Whenatroubleconditionrestores,theunitsredoutputLED,[OUT1-OUT4]
willblinkwithashorteranddistinctlyadifferentduration.ThegreeninputLEDswillbeoff(normalcondition).
Toresetthememorydepresstheresetbutton(Fig. 2c, pg. 7).TheLED(s)willextinguish.
Note:Ifindicatingcircuitshavebeenrestored,memoryresetisnotrequiredfornormaloperationoftheunit.
AL602ULADA - 7 -
This connection is used to
monitor AC and Bat Fail and
will cause a simultaneous trouble
condition to the FACP's IN1 and IN2
Common trouble output to
Digital Communicator or
Local Annunciator Dry output Contact
(Form "C" contacts) (Non-Supervised)
4-wire Smoke
Detector
+
--
+
--
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
from
FACP
SW1
-- DC +
SW2
+ OUT1 --
OUT1 OUT2 OUT3 OUT4
INP1 INP2
FAULT
NC CNOC"FAULT" NC
OUT1 OUT3
OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
IN1+ IN1-- IN2--
IN2+ C "DRY1" NC
RET1+RET1-- RET2--
RET2+ C "DRY2" NC
+ OUT2 -- + OUT3 -- + OUT4 --
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
-- AUX +
UPPER TERMINALS
LOWER TERMINALS
Addressable
Control Module
Trigger Output
See Note 2
line
ground
neutral
GreenLead
GreenLead
ACLocal
Divider
Use separate knockout. Keep 1/4" spacing from
non power limited wiring
RegulatedPower-LimitedOutputs
2.5ampmax.per
outputinalarm
(total=6.5amp)
(Supervised)
Supervised Non-Supervised
Non-Supervised
Non-Supervised
RESET
unswitched 120VAC
power mains
(non-power limited)
Non-powerlimite
d
Supervised
Non-powerlimited
5A
250V
Fig. 2
This connection is used to
monitor AC and Bat Fail and
will cause a simultaneous trouble
condition to the FACP's IN1 and IN2
Common trouble output to
Digital Communicator or
Local Annunciator Dry output Contact
(Form "C" contacts) (Non-Supervised)
4-wire Smoke
Detector
+
--
+
--
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
from
FACP
SW1
-- DC +
SW2
+ OUT1 --
OUT1 OUT2 OUT3 OUT4
INP1 INP2
FAULT
NC CNOC"FAULT" NC
OUT1 OUT3
OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
IN1+ IN1-- IN2--
IN2+ C "DRY1" NC
RET1+RET1-- RET2--
RET2+ C "DRY2" NC
+ OUT2 -- + OUT3 -- + OUT4 --
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
-- AUX +
UPPER TERMINALS
LOWER TERMINALS
Addressable
Control Module
Trigger Output
See Note 2
line
ground
neutral
GreenLead
GreenLead
ACLocal
Divider
Use separate knockout. Keep 1/4" spacing from
non power limited wiring
RegulatedPower-LimitedOutputs
2.5ampmax.per
outputinalarm
(total=6.5amp)
(Supervised)
Supervised Non-Supervised
Non-Supervised
Non-Supervised
RESET
unswitched 120VAC
power mains
(non-power limited)
Non-powerlimited
Supervised
Non-powerlimited
5A
250V
NC CNOC"FAULT" NC
Fig. 2b
Fig. 2a
These circuits are used to
monitor AC and Bat Fail and
will cause a simultaneous trouble
condition to the FACP's IN1 and IN2
Digital Communicator or
Local Annunciator Dry output Contact
(Form "C" contacts)
4-wire Smoke
Detector
+
--
+
--
4-wire Smoke
Detector
Fire
Alarm
Control
Panel
(FACP)
EOL Power
Supervision Relay
(Not Supplied)
EOL
Resistor
from
FACP
SW1
-- DC +
SW2
+ OUT1 --
OUT1 OUT2 OUT3 OUT4
INP1 INP2
FAULT
NC CNOC"FAULT" NC
OUT1 OUT3
OUT2 OUT4
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
IN1+ IN1-- IN2--
IN2+ C "DRY1" NC
RET1+RET1-- RET2--
RET2+ C "DRY2" NC
+ OUT2 -- + OUT3 -- + OUT4 --
INPUT SELECT
TEMPORAL
STROBE SYNC
IN > OUT SYNC
-- AUX +
UPPER TERMINALS
LOWER TERMINALS
Addressable
Control Module
Trigger Output
See Note 2
+ DC ---
BAT FAIL
NO C NC NO C NC
+ BAT ---
DC
AC FAIL
L G N
AC
Fuse
Cover15A
250V
10A
250V
line
ground
neutral
unswitched 120VAC
power mains
(non-power limited)
GreenLead
Use separate knockout.
Keep 1/4" spacing from
non power limited wiring
PowerLimitedOutputs
2.5ampper
outputinalarm
(total=10amp)
RESET
J2
Fig. 2c
TroubleMemory
ResetButton
Commontrouble
Input/Output
Hookup Diagram:
- 8 - AL602ULADA
Optional hookups:
1- BatteryandACmonitoring:ACorBatteryFailconditionwillcausethecommontroubleinput[C“FAULT”NC]to
reportbacktotheFACPviainput1andinput2.Thecommontroubleinputmayalsobeusedforotheroptional
supervisorymonitoring.(see Power Board Parameter for use of AC Delay, pg. 6)
ToreportACandBatteryTroubleconnectthebatteryandACFailrelayoutputshownin(Fig. 2a)tothe
commontroubleinput.
2- Drycontactinput(C“DRY1”NC)(C“DRY2”NC)canbeusedtoalarmoutputfroman
addressablemodule(theseinputsareunidirectionandcannotreportbacktotriggermodule).
Connection to triggering devices must be made within 20ft of distance and using conduit for wiring.
3- Auxiliaryoutput(-AUX+)24VDCat1ampmax.
4- ACLocal[NC,NO,C]shouldconnecttothehostcontrolpanelforlocalannunciationof
thetroublecondition.
Note: Ifcommontroubleinput,terminalsmarked[C“FAULT”NC]arenotused,theseterminalsmustbe
shorted(connectjumper)toremaininactive.Foroptionalhookups(Fig. 2b).
Maintenance:
Unitshouldbetestedatleastonceayearfortheproperoperationasfollows:
Output Voltage Test:UndernormalloadconditionstheDCoutputvoltageshouldbecheckedforpropervoltagelevel
(26.2-26.4VDC recommended range).
Battery Test:Undernormalloadconditionscheckthatthebatteryisfullycharged.Checkspecifiedvoltage
bothatthebatteryterminalandattheboardterminalsmarked[+BAT--]toensurethatthereisnobreakinthebattery
connectionwires.
Fuses:Checkinputfuseonthepowersupplyboard,replaceifnecessary.Inputfuseratingis5amp@250V.
Note:Maximumchargingcurrentis650mA.
Note:Expectedbatterylifeis5years;however,itisrecommendedchangingbatteriesin4yearsorlessifneeded.
AL602ULADA - 9 -
Battery Calculation Worksheet
Unitsarecapableofrecharging40AHbatterymax.Iftotalampere-hourrequiredexceeds40AH,
decreaseAUXcurrenttoprovideenoughstand-bytimefortheapplication.
Device Number of
Devices Current per Device Stand-by
Current
Alarm
Current
Foreachdeviceusethisformula: Thiscolumn x Thiscolumn = Equals Currentpernumberofdevices.
AL602ULADA
(Currentdrawfrombattery) 1Stand-by: 90mA 90mA
Alarm: 175mA 175mA
AAL602 Current 90mA 175mA
AuxiliaryDevices Refertodevicemanualforcurrentratings.
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
Alarm/Stand-by mA mA mA
BAuxiliary Devices Current (must not exceed 1 amp)
Refertodevicemanualforcurrentratings.
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
Alarm: mA 0mA mA
CNotificationAppliancesCurrent must notexceed6.5amp(6500mA) 0mA mA
DTotalalarmcurrent mA mA
ETotalcurrentratingsconvertedtoamperes(lineDx.001) A A
FNumberofstandbyhours(24forNFPA72,Chapter1,1-5.2.5). H
GMultiplylinesEandF. Totalstand-byAH AH
HAlarmsoundingperiodinhours.
(Forexample,5minutes=.0833hours.) H
IMultiplylinesEandH. TotalalarmAH AH
JAddlinesGandI. Totalstand-byandalarmAH AH
K
MultiplylineJby1.30.
(30%extrainsurancetomeetdesiredperformance)
Totalampere-hoursrequired
AH
- 10 - AL602ULADA
Appendix A - UL Listed Compatible Devices
A.1 Four (4) Wire Smoke Detectors
TableA-1belowlistsfour(4)wiresmokedetectorscompatiblewithAL602ULADAAUXoutput.
Smoke Detector/BaseDetector Type Max Standby
Current (mA)
Alarm
Current (mA)
FenWalCPD-7021(w/70-201000-005Base) Ionization 0.10 *
FenWalPSD-7125 Photoelectric 0.10 *
FenWalPSD-7125(w/70-201000-005Base) Photoelectric 0.10 *
Fire-LiteBLP-12-4W Base * *
Gentex824 Photoelectric 0.50 *
Gentex824T Photoelectric 0.50 *
Gentex824CP Photoelectric 0.50 *
Gentex824CPT Photoelectric 0.50 *
HochikiHSC-4R Base * *
HochikiSPB-24 ProjectedBeam 0.25 *
SystemSensorB112LP Base 0.12 36
SystemSensorB114LP Base * *
SystemSensorB404B Base * *
SystemSensorDH100ACDC Photoelectric 0.15 0.70
SystemSensorDH100ACDCLP Photoelectric 0.15 0.70
SystemSensorDH100ACDCLPW Photoelectric 0.15 0.70
SystemSensorDH400ACDCI IonizationDuct 25 95
SystemSensorDH400ACDCP PhotoelectricDuct 25 95
SystemSensor1112/24/D Ionization 0.05 50
SystemSensor1424 Ionization 0.10 41
SystemSensor1451(w/B402BBase) Ionization 0.10 39
SystemSensor2112/24ATR Photoelectric 0.50 60/70
SystemSensor2112/24AITR Photoelectric 0.50 60/70
SystemSensor2112/24/D Photoelectric 0.05 50
SystemSensor2112/24R Photoelectric 0.50 60/70
SystemSensor2112/24TR Photoelectric 0.50 60/70
SystemSensor2112/24T/D Photoelectricw/135oThermal 0.05 50
SystemSensor2112/24TSRB Photoelectricw/135o
ThermalSupervisoryRelay 15 45
SystemSensor2312/24TB Photoelectric 0.12 50
SystemSensor2412(12volt) Photoelectric 0.12 77
SystemSensor2412AT(12volt) Photoelectric 0.12 58
SystemSensor2412TH(12volt) Photoelectric 0.12 77
SystemSensor2424 Photoelectric 0.10 41
SystemSensor2424TH Photoelectric 0.10 41
SystemSensor2451 Photoelectric 0.10 39
SystemSensor2451TH(with/B402BBase) Photoelectric 0.10 39
SystemSensor2W-MOD LoopTest/MaintenanceMod. 30 50
AL602ULADA - 11 -
A.1 Four (4) Wire Smoke Detectors (cont.)
Smoke Detector/BaseDetector Type Max Standby
Current (mA)
Alarm
Current (mA)
SystemSensor4W-B(12/24volt) PhotoelectricI3.05 23
SystemSensor4WT-B(12/24volt) PhotoelectricI3w/Therm .05 23
SystemSensor4WTA-B(12/24volt) I3Photow/Therm/Sounder .05 35
SystemSensor4WTR-B(12/24volt) I3Photow/Therm/Relay .05 35
SystemSensor4WTR-B(12/24volt) I3Photow/Therm/
Sounder/Relay .05 50
SystemSensor4WITAR-B(12/24volt) I3Photow/IsolatedTherm/
Sounder/Relay .05 50
SystemSensor2W-MOD2 I3LoopTest/Maintenance
Mod. .05 *
SystemSensorRRS-MOD I3ReversingRelay/Sync
Module .05 *
SystemSensor6424 ProjectedBeam 10 28.4
SystemSensorBeam1224(S) ProjectedBeam 17 38.5
*Contactmanufacturerforcurrentdraws
A.2 Door Holders
TableA-2belowlistsdoorholderscompatiblewithAL602ULADAAUXoutput.
Manufacturer Model Type Current (mA)
Edwards DH150A FloorMount 96
Edwards DH154A FloorMount 96
Edwards DH158A SurfaceMount 96
RixonFiremark FM-980 FloorMount,single 68
RixonFiremark FM-996 SurfaceWiring 68
RixonFiremark FM-998 ConcealedWiring 68
A.3 Relays
TableA-3belowlistsrelayscompatiblewithAL602ULADAAUXoutput.
Manufacturer Model Current (mA)
AirProducts&
Controls,LTD
MR-101/C
MR-201/C
PAM-1
PAM-2
PAM-SD
A77-716B
15
35
15
15
15
20
Manufacturer Model Current (mA)
SystemSensor
PR-1
PR-2
PR-3
EOLR-1
R-10T
R-14T
R-20T
R-24T
R-10E
R-14E
R-20E
R-24E
15
30
30
30
23
23
40
40
23
23
40
40
- 12 - AL602ULADA
A.4 Strobes
TableA-4belowlistsstrobescompatiblewithAL602ULADANACoutput.
Wheelock Devices:
Sychronizing Horns
AH-12
AH-12WP
HS-24
NH-12/24
ZNH
HNR
AH-24AH-24
AH-24WP
MIZ-24S
HNW
Sychronizing Horn Strobes
AS-121575W
AS-24MCW
AS-24MCWH
AS-2415C
AS-2475C
ASWP-2475W
NS4-121575W
HS4-241575W
HS4-24MCW
HS4-24MCWH
HS4-24185W
ZNS-MCW
ZNS-MCWH
HSR
AS-241575W
AS-24MCC
AS-24MCCH
AS-2430C
AS-24100C
NS-121575W
NS-2-41575W
NS-24MCW
HS4-24150C
HSW
Sychronizing Strobes
RSS-121575W
RSS-241575W
RSS-24MCW
RSS-24MCC
RSS-2415C
RSS-2430C
RSS-2475C
RSS-24100C
RSS-2415CR
RSS-2430CR
RSS-2475CR
RSS-24100CR
RSS-24150C
RSS-24177C
RSS-24150W
RSS-24177W
RSS-24185W
RSS-24150CR
RSS-24177CR
RSSWP-2475W
ZRS-MCW
ZRS-MCWH
STR
RSSP-121575W
RSSP-241575W
RSSP-24MCW
RSSP-24150W
RSSP-24177W
RSSP-24185W
STW
Appliances with Sychronizing Strobes
AMT-241575W
AMT-2475W
AMT-241575W-NYC
AMT-2475W-NYC
MT-12575W
MT-241575W
MTWP-2475W
CH70-24MCW
CH70-24MCC
CH70-2415C
CH70-2430C
CH70-2475C
CH70-24100C
CH70-24150C
CH70-24177C
CH70-24150W
CH70-24MCWH
CH70-24185W
E70-24MCW
E70-24MCC
E70-2415C
E70-2430C
E70-2475C
E70-24100C
E70-24150C
E70-24177C
E70-24150W
E70-24MCWH
E70-24185W
ET70-24MCW
ET70-24MCC
ET70-2415C
ET70-2430C
ET70-2475C
ET70-24100C
ET70-24150C
ET70-24177C
ET70-24150W
ET70-24MCWH
ET70-24185W
SA-70-24-SL
SA-70-24-SLM
AMT4-241575W
AMT4-2475W
AMT4-241575W-NYC
AMT4-2475W-NYC
MT-2475W
ET70WP-2475W
CH90-24MCW
CH90-24MCC
CH90-2415C
CH90-2430C
CH90-2475C
CH90-24100C
CH90-24150C
CH90-24177C
CH90-24150W
CH90-24MCCH
CH90-24185W
E90-24MCW
E90-24MCC
E90-2415C
E90-2430C
E90-2475C
E90-24100C
E90-24150C
E90-24177C
E90-24150W
E90-24MCCH
E90-24185W
ET90-24MCW
ET90-24MCC
ET90-2415C
ET90-2430C
SA-90-24-SL
SA-90-24-SLM
AL602ULADA - 13 -
A.4 Strobes (cont.)
Wheelock Devices:
Coded Audible Appliances
AMT-12/24
AMT-12/24-NYC
CH70
CSX10-24-DC
MT-12/24
AMT4-12/24
AMT4-12/24-NYC
CH90
CSXG10-24-DC
MT4-12/24
Non-Synchronizing Appliances
MB-G6-12
MB-G10-12
MIZ-TC12
MB-G6-24
MB-G10-24
MIZ-TC24
Gentex Devices:
Models
GE3Series
GES/GECSeriesGCS/
GCCSeries
SSPKWallandCeilingMountSeries
GX93Series
WGEandcolorlenseunits.
System Sensor Devices:
Wall Horn/Strobes
P2R
P2RH
P2RK
P2RHK
P2W
P2WH
P4R
P4RH
P4RK
P4RHK
P4W
P4WH
Wall Strobes
SR
SRH
SRK
SRHK
SW
SWH
Ceiling Horn/Strobes
PC2R
PC2RH
PC2RK
PC2RHK
PC2W
PC2WH
PC4R
PC4RH
PC4RK
PC4RHK
PC4W
PC4WH
Ceiling Strobes
SCR
SCRH
SCRK
SCRHK
SCW
SCWH
Horns
HR
HRK
HW
- 14 - AL602ULADA
A.4 Strobes (cont.)
Amseco Devices:
Models
H24R
H24W
HP-25T
MH12/24
MH-120
RSD24-153075
RSD24W75110
SAD-24-153075
SAD2475110
SCM24C-177
SCM24W075110
SCM24W-153075
SCM24W3075110
SH24C-177
SH24C-3075110
SH24W-1530
SH24W3975110
SH24W-75110
SHB/SLB120-75
SHB/SLB24-75
SHB2475
SL24C-177
SL24C-3075110
SL24W-1530
SL24W-75110
SLB24-75
Faraday Devices:
Models
HS-MC-R
HS-MC-W
HS-HMC-R
HS-HMC-W
HS-R
HS-W
NS-MC-CR
NS-MC-CW
NH-CR
NH-CW
SET-MC-R
SET-MC-W
SET-HMC-R
SET-HMC-W
SET-S17R-WP
SET-S17-W-WP
SET-S17-CW-WP
SET-MC-CW
SET-MC-CR
SET-HMC-CW
SET-HMC-CR
SET-177-CR-WP
SET-177-CW-WP
SET-185-R-WP
SET-185-W-WP
SEF-MC-R
SEF-MC-W
SEF-HMC-R
SEF-HMC-W
SEF-MC-CW
SEF-HMC-CW
ZH-MC-R
ZH-MC-W
ZH-HMC-R
ZH-HMC-W
ZH-R
ZH-W
ZH-MC-CR
ZH-MC-CW
ZH-HMC-CR
ZH-HMC-CW
ZR-MC-CW
ZR-MC-CW
ZR-HMC-CR
ZR-HMC-CW
ZBB-R
ZBB-W
MTH-R
MTH-W
MTH-MC-R
MTH-MC-W
MTH-75-R-WP
MTH-15-115-R-WP
MTH-HMC-CR-WP
MTH-HMC-R-WP
MTH-HMC-W-WP
SE-MC-R
SE-MC-W
SE-HMC-R
SE-HMC-W
SE-CR
SE-CW
SE-MC-CR
SE-HMC-CW
SE-CR
SE-CW
SE-MC-CR
SE-MC-CW
SE-HMC-CR
SE-HMC-CR
AS-MC-R
AS-MC-W
AS-HMC-R
AS-HMC-W
AS-MC-CR
AS-MC-CW
AS-HMC-CR
AS-HMC-CW
AS-75-R-WP
AS-75-CR-WP
AH-R
AH-W
AH-WP
AL602ULADA - 15 -
Notes:
- 16 - AL602ULADA
Enclosure Dimensions:
15.5”x12”x4.5”(393.7mmx304.8mmx114.3mm)
Altronixisnotresponsibleforanytypographicalerrors.
14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-9056
website:www.altronix.com,e-mail:[email protected],LifetimeWarranty,MadeinU.S.A.
IIAL602ULADA K13M MEMBER
1.5”
(38.1mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
5.0”
(127.0mm)
5.0”
(127.0mm)
1.5”
(38.1mm)
2.0”
(50.8mm)
2.0”
(50.8mm)
1.75”
(44.45mm)
1.75”
(44.45mm)
4.5”
(114.3mm)
1.25”
(31.75mm)
4.5”
(114.3mm) 1.25”
(31.75mm)
1.25”
(31.75mm)
1.25”
(31.75mm)
1.1”
(27.94mm)
1.1”
(27.94mm)
0.79”
(20.06mm)
1.1”
(27.94mm)
0.91”
(23.114mm)
0.91”
(23.114mm)
1.375”
(34.925mm)
1.125”
(28.575mm)
15.5”
(393.7mm)
4.615”
(117.22mm)
12.23”
(310.64mm)
4.615”
(117.22mm)
1.5”
(38.1mm)
1.5”
(38.1mm)
4.615”
(117.22mm)
4.615”
(117.22mm)
Other manuals for AL602ULADA
2
Table of contents
Other Altronix Extender manuals
Altronix
Altronix AL642ULADA User guide
Altronix
Altronix AL642ULADA User guide
Altronix
Altronix eBridge PLUS User manual
Altronix
Altronix AL802ULADAJ User manual
Altronix
Altronix AL602ULADA User guide
Altronix
Altronix AL802ADA220J User manual
Altronix
Altronix AL642ADA220 User guide
Altronix
Altronix AL602ADA220 User guide
Altronix
Altronix AL1002ULADAJ User manual
Altronix
Altronix AL1002ULADA User manual
Altronix
Altronix AL802ULADA User manual
Altronix
Altronix AL602ADA220J User manual
Altronix
Altronix AL1002ULADA User manual
Altronix
Altronix AL602ULADAJ User manual
Altronix
Altronix AL602ULADAJ User guide
Altronix
Altronix AL602ADA220 User manual
Altronix
Altronix AL1002ADA220 User manual
Altronix
Altronix AL802ULADA User manual
Altronix
Altronix AL602ULADAJ User guide
Altronix
Altronix AL602ULADAJ User manual
