Altronix SMP3CTX Series User manual

SMP3CTX Series Installation Guide
Overview:
These units convert a 115VAC or 230VAC, 50/60Hz input into a regulated 12VDC or 24VDC output up to 2.5A of con-
tinuous load current (see specifications).
SMP3CTX Series Power Supply Configuration Reference Chart:
Altronix
Model Number
Accessory
Power
Distribution
Module(s)
Number
of
Outputs
Fused
Outputs
PTC
Outputs
Individual
Output
Rating (A) Supervised
115VAC/
230VAC
Input
Current (A)
12VDC/
24VDC
Total Output
Current (A)
SMP3CTX
---- 1 ---- ---- 2.5A
----
0.65A/0.35A 2.5A
SMP3PMCTX
P
SMP3PMCTXX
SMP3PMP4 PD4 4 P---- 2.5A
SMP3PMP4CB PD4CB ---- P2.5A
SMP3PMP8 PD8 8 P---- 2.5A
SMP3PMP8CB PD8CB ---- P2.5A
SMP3PMP16 PD16W 16 P---- 2.5A
SMP3PMP16CB PD16WCB ---- P2.5A
Specifications:
Agency Listings:
• CE European Conformity.
Input:
• Input 115VAC, 50/60Hz, 0.65A or
230VAC, 50/60Hz, 0.35A.
Output:
• 12VDC or 24VDC selectable output.
• 2.5A supply current.
• Filtered and electronically regulated outputs.
• Short circuit and thermal overload protection.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Maximum charge current 0.5A.
• Zero voltage drop when switching over to battery backup.
Features:
• Power ON/OFF switch.
Supervision (select models):
• AC fail supervision (form “C” contacts).
• Low battery supervision (form “C” contacts).
Visual Indicators:
• AC input and DC output LED indicators.
Electrical:
• Operating temperature: 0º C to 49º C ambient.
Mechanical:
• Enclosure Dimensions (H x W x D approx.):
SMP3CTX, SMP3PMCTX, SMP3PMP4,
SMP3PMP4CB, SMP3PMP8, SMP3PMP8CB,
SMP3PMP16, SMP3PMP16CB:
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
- Accommodates up to two (2) 12VDC/7AH batteries.
SMP3PMCTXX:
15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)
- Accommodates up to two (2) 12VDC/12AH batteries.
Power Supply Voltage Output Specifications:*
Output VDC Switch Position Max. Load DC
12VDC SW1 - ON (Fig. 1c, pg. 3) 2.5A
24VDC SW1 - OFF (Fig. 1c, pg. 3) 2.5A
*Specified at 25˚ C ambient.
Installation Instructions:
Wiring methods should be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 4).
Secure enclosure to earth ground.
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

2. Slide [Power ON/OFF] switch to OFF position.
3. Set SW1 on the power supply board to the desired DC output voltage (Fig. 1c, pg. 3) (Power Supply Voltage
Output Specification Chart).
4. Connect AC power to the terminals marked [L & N], connect ground to the green flying lead (Fig. 1, pg. 3).
Use 18 AWG or larger for all power connections (Battery, DC output).
Use 22 AWG to 18 AWG for power-limited circuits (AC Fail/Low Battery reporting).
5. Slide [Power ON/OFF] switch to ON position.
6. Measure output voltage before connecting devices. This helps avoiding potential damage.
CAUTION: Do not touch exposed metal parts. Shut branch circuit power before installing or servicing equipment.
There are no user serviceable parts inside. Refer installation and servicing to qualified service personnel.
7. Slide [Power ON/OFF] switch to OFF position.
8. Connect devices to be powered:
a. For Power Supply Board connect to the terminals marked [– DC +].
b. For Power Distribution Module(s) connect devices to be powered to the terminal pairs 1 to 4 marked
[1P & 1N] through [4P & 4N] (Fig. 2, pg. 3), 1 to 8 marked [1P & 1N] through [8P & 8N] (Fig. 3, pg. 3),
or 1 to 16 marked [1P & 1N] through [16P & 16N] (Fig. 4, pg. 3), carefully observing correct polarity.
Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board (Fig. 1a, pg. 3).
When servicing the unit, AC mains should be removed.
9. When using stand-by batteries, they must be lead acid or gel type.
Connect battery to the terminals marked [– BAT +] (battery leads included).
12VDC operation: Use one (1) 12VDC battery.
24VDC operation: Use two (2) 12VDC batteries connected in series.
Note: When batteries are not used, a loss of AC will result in the loss of output voltage.
For supervised models only:
10. Connect appropriate signaling notification devices to AC Fail and Low Bat supervisory relay outputs
marked [NC, C, NO] (Fig. 1b, pg. 3).
11. Slide [Power ON/OFF] switch to ON position.
LED Diagnostics:
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
Terminal Identification:
Power Supply Board:
Terminal Legend Function/Description
L, G, N Connect 115VAC/230VAC to these terminals: L to Hot, N to Neutral.
– DC + 12VDC / 24VDC @ 2.5A continuous output.
*AC FAIL
NC, C, NO
Used to notify loss of AC power, e.g. connect to audible device or alarm panel. Relay normally
energized when AC power is present. Contact rating 1A @ 120VAC / 28VDC.
*Low Battery
NC, C, NO
Used to indicate low battery condition, e.g. connect to alarm panel. Relay normally
energized when DC power is present. Contact rating 1A @ 120VAC / 28VDC.
Low battery threshold:
12VDC output threshold set @ approximately 10.5VDC,
24VDC output threshold set @ approximately 21VDC.
– BAT + Stand-by battery connections. Maximum charge rate 0.5A.
*Note: Supervised models only
PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module:
Terminal Legend Function/ Description
PD4/PD4CB PD8/PD8CB PD16W/PD16WCB
1P to 4P 1P to 8P 1P to16P Positive DC power outputs.
1N to 4N 1N to 8N 1N to 16N Negative DC power outputs.
- 2 - SMP3CTX series
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

Fig. 1 CAUTION: De-energize unit prior to servicing. Do not expose to rain or moisture.
Switch disables power mains
line voltage input.
If stand-by battery (batteries) are
connected, the DC output remains on.
Fig. 1a
Fig. 1b
LED Diagnostics
Power Supply
Board
L G N
ON OFF
AC DC
5A 250V
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT + --- DC +
Power
Distribution
Module(s)
Green
Lead
Wire
Strap
(from
Enclosure
to Door)
115/230VAC
power
mains
INPUT
LOW BAT
NC C NO NC C NO
AC FAIL
Optional RechargeableOptional Rechargeable
Red Green Power Supply Status
(DC) (AC)
ON ON Normal operating condition.
ON OFF Loss of AC. Stand-by battery
(batteries) supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by
battery (batteries). No DC output.
Stand-by BatteryStand-by Battery
CAUTION: Optional rechargeable stand-by batteries must match
the power supply output voltage setting.
ON OFF
Battery and AC
Supervision
Circuit
ON
1
Switch On - 12V
Switch Off - 24V
OFF --- 2�V ON --- �2V
ON
Fig. 1c
SW1
24VDC output - OFF
12VDC output - ON
Power Distribution Module(s):
Fig. 2
INPUT
LED
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
F1 F2 F3 F4
COMMON POWER OUTPUTS
1P 1N 2P 2N 3P 3N 4P 4N
DC Output to devices From Power Supply
Board
(Factory Installed)
Used on
PTC Models
Fig. 3
N
COMMON POWER OUTPUTS
P
FUSED POWER OUTPUTS
1 2 3 4 5 6 7 8
D1
INPUT
R1 LED
DC Output to devices From Power Supply
Board
(Factory Installed)
ON OFF
SW1
Used on
PTC Models
Fig. 4
Used on
PTC Models
common
outputs
protected
outputs
P
N
NPS
XFMR Input
12345678
9 10 11 12 13 14 15 16
P N
3.5A 250V
For continuous protection against risk of fire
replace fuses with same type and rating.
SMP3CTX series - 3 -
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]

Enclosure Dimensions (H x W x D approx.) (BC300):
SMP3CTX, SMP3PMCTX, SMP3PMP4, SMP3PMP4CB,
SMP3PMP8, SMP3PMP8CB, SMP3PMP16, SMP3PMP16CB
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.55mm)
Enclosure accommodates up to
two (2) 12VDC/7AH batteries.
(
25mm
) (
267mm
)
1.40”
(36mm)
1.40”
(36mm)
4.85”
(123mm)
4.85”
(123mm)
1.40”
(36mm)
1.40”
(36mm)
5.10”
(130mm)
5.10”
(130mm)
13.0”
(330mm)
5.10”
(130mm)
6.5625”
(167mm)
1.20”
(31mm)
1.20”
(31mm) 1.20”
(31mm)
3.25”
(83mm)
3.25”
(83mm)
3.25”
(83mm)
3.25”
(83mm)
1.0”
(25mm)
1.0”
(
25mm
)
10.5”1.0”
1.0”
(25mm)
0.75”
(19mm)
0.75”
(19mm)
0.9375”
(24mm)
0.9375”
(24mm)
11.0”
(279mm)
12.5”
(318mm)
Enclosure Dimensions (H x W x D approx.) (BC400):
SMP3PMCTXX
15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)
Enclosure accommodates up to
two (2) 12VDC/12AH batteries.
(50.8mm)
(50.8mm)
(127.0mm)
1.25”
(31.75mm) (31.75mm)
1.75”
(44.45mm)
(38.1mm) (117.22mm) (117.22mm) (38.1mm)
5.0”
2.0”
2.0”
1.25”
1.5”
(38.1mm) 1.5” (38.1mm)
1.5”
(38.1mm)
5.0”
(127.0mm)
1.5”
(38.1mm)
1.75”
(44.45mm)
4.5”
(114.3mm)
1.25”
(31.75mm)
4.5”
(114.3mm) 1.25”
(31.75mm)
1.1”
(27.94mm)
1.1”
(27.94mm)
0.79”
(20.06mm)
1.1”
(27.94mm)
0.91”
(23.114mm)
0.91”
(23.114mm)
1.375”
(34.925mm)
1.125”
(28.575mm)
15.5”
(393.7mm)
4.615”
(117.22mm)
12.23”
(310.64mm)
4.615”
(117.22mm)
1.5” 1.5”
4.615” 4.615”
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: [phone]
web site: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A.
IISMP3CTX series - Rev. 121812 C31P MEMBER
- 4 - SMP3CTX series
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]