Altronix WayPoint17A User manual

AC Outdoor
Power Supplies
Models Include:
WayPoint10A
- 24VAC @ 4A and/or 28VAC @ 3.5A.
WayPoint17A
- 24VAC @ 7.25A and/or 28VAC @ 6.25A.
WayPoint30A
- 24VAC @ 12.5A or 28VAC @ 10A.
Installation Guide
Rev. 080911ACPL More than just power.TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________

- 2 - WayPoint AC Series Installation Guide
Overview:
WayPoint Outdoor Power Supplies provide 24VAC or 28VAC distributed via one or two output(s) for powering
CCTV cameras, heaters and other video accessories.
WayPoint AC Reference Chart:
Altronix
Model Number Output Voltage
Total Output
Current
(Power)
Fuse
Output
Ratings
Input Current Draw
Product
Weight
115VAC
50/60Hz
230VAC
50/60Hz
WayPoint10A
24VAC 4A
5A/250V 1.2A 0.7A 10.3 lbs.28VAC 3.5A
24VAC and 28VAC 3.5A
WayPoint17A
24VAC 7.25A
10A/250V 1.7A 1.0A 13.1 lbs.28VAC 6.25A
24VAC and 28VAC 6.25A
WayPoint30A
24VAC 12.5A
15A/32V 3.5A 2.0A 14.1 lbs.28VAC 10A
24VAC and 28VAC 10A
Specifications:
Installation Instructions:
Unit should be installed in accordance with The National Electrical Code and all applicable Local Regulations.
1. Remove back plane from enclosure prior to mounting (do not discard hardware).
2. Mark and drill desired inlets on the enclosure to facilitate wiring (Fig. 1, pg. 3).
3. Mount unit in desired location.
Wall mount: Mount unit in desired location. Mark and drill holes to line up with the top and bottom
hole of the enclosure flange. Secure enclosure with appropriate fasteners (e. g. screws
and anchors; bolts and locking nuts, etc.) that are compatible with mounting surface and
are of sufficient length/construction to ensure a secure mount (Fig. 5, pg. 7).
Pole Mount: Refer to Fig. 6 - 10, pg. 7) .
4. Mount back plane to enclosure with hardware.
5. Set the input voltage selector switch for 115VAC or 230VAC operation (Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6)
6. To facilitate wire entry utilize weather tight NEMA 4 rated connectors, bushings and cable.
7. Set illuminated master power disconnect circuit breaker to the (OFF) position
(Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
8. Connect unswitched AC power (115VAC/230VAC 50/60 Hz) to terminals marked [L, G, N]
(Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
Wire gauge range of connectors is 14 AWG to 11 AWG (1.6 mm to 2.5 mm diameter).
9. Set illuminated master power disconnect circuit breaker to the (RESET/ON) position
(Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
Agency Listings:
• CE European Conformity.
Input:
• Input: 115VAC, 50/60Hz or 230VAC, 50/60Hz.
Output:
• Output options:
a. 24VAC or 28VAC.
b. Both 24VAC and 28VAC.
Visual Indicators:
• Individual power output LED indicators.
• Illuminated master power switch with
built-in circuit breaker.
Features:
• Surge suppression.
• Spare fuses included.
Accessories:
• Optional PMK1 Pole Mount Kit simplifies installation
of outdoor units.
Enclosure:
• NEMA 4/4X, IP66-11 Rated enclosure for
outdoor use.
• Enclosure Dimensions (H x W x D approx.):
13.31” x 11.31” x 5.59”
(338.074mm x 287.274mm x 141.986mm)

WayPoint AC Series Installation Guide - 3 -
10. Measure output voltage on terminals marked [COM, 24V, 28V] before connecting devices
(Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6). This helps avoiding potential damage.
11. Set illuminated master power disconnect circuit breaker to the (OFF) position
(Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
12. For 24VAC output connect devices to terminals marked [COM, 24V] (Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
For 28VAC output connect devices to terminals marked [COM, 28V] (Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
13. Set illuminated master power disconnect circuit breaker to the (RESET/ON) position
(Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
14. LEDs will illuminate indicating each output is powered (Fig. 2, pg. 4, Fig. 3, pg. 5, Fig. 4, pg. 6).
15. Upon completion of wiring, secure enclosure door with latches and optional lock.
Caution: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
WARNING: When installing in a non-restricted service area use lock or other fastened means
on door latches. This installation should be made by qualified service personnel and should
conform to the National Electrical Code and all local codes.
Terminal and LED Identification Chart:
Output
Terminals LED LED Status
ON OFF
COM & 24V 24VAC Normal operating condition. No AC output. Blown fuse, illuminated master power
disconnect circuit breaker is tripped or OFF, AC failure.
COM & 28V 28VAC
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of
sufficient magnitude to constitute an electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-
tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION: To reduce the risk of electric shock do not open enclosure.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.
Fig. 1
Bottom of Enclosure
Suggested
Locations
for Wiring Inlets

- 4 - WayPoint AC Series Installation Guide
5A 250V
INPUT
OUTPUT
28V 24V COM
COM 24V 28V
24VAC 28VAC
CAUTION
HIGH VOLTAGE
LGN
POWER INPUT
VOLTAGE
SELECTOR
115V
230 115
Fig. 2 - WayPoint10A

WayPoint AC Series Installation Guide - 5 -
Fig. 3 - WayPoint17A
10A 250V
INPUT
OUTPUT
28V 24V COM
COM 24V 28V
24VAC 28VAC
LGN
POWER INPUT
VOLTAGE
SELECTOR
115V
230 115
CAUTION
HIGH VOLTAGE

- 6 - WayPoint AC Series Installation Guide
Fig. 3 - WayPoint30A
XFMR*
INPUT
15A 32V
INPUT
OUT1
28V 24V COM
COM 24V 28V
24VAC 28VAC
15A 32V
24VAC 28VAC
LGN
OUT2
COM 24V 28V
POWER INPUT
VOLTAGE
SELECTOR
115V
230 115
CAUTION
HIGH VOLTAGE

WayPoint AC Series Installation Guide - 7 -
Wall Mount Installation:
1- Place unit at desired location and secure with mounting
screws (not included) (Fig. 5, pg. 7).
Fig. 5
Pole Mounting Using Optional Pole Mount Kit PMK1:
This installation should be made by qualified service personnel. This product contains no serviceable parts.
PMK1 outdoor pole mount kit is designed to simplify the installation of Altronix outdoor rated power supplies and
accessories housed in models WP1, WP3 and WP4 NEMA rated enclosures. PMK1 can be mounted on 2” to
8” (50.8mm to 203.2mm) diameter round or 5” (127mm) square poles. Brackets are designed for use with the
Wormgear Quick Release Straps (two included).
1. Thread one (1) wormgear quick release strap through the slots on the back of a mounting bracket (Fig. 6, pg. 7).
2. Once the desired height of the top Pole Mount bracket is achieved, tighten the straps down by sliding open
end of the strap through the locking mechanism on the strap, then tighten the screw with
flat head screwdriver or 5/16” hex socket driver (Fig. 7, pg. 7 and Fig. 9, pg. 7).
3. Attach the bottom bracket to the enclosure by inserting bolts through the flange of the enclosure and into the
bracket, tightening bolts with a 7/16” hex socket (Fig. 8, pg. 7).
4. Thread the second wormgear quick release strap through the slots on the back of the bottom mounting
bracket (Fig. 9, pg. 7).
5. Mount enclosure onto the top bracket by inserting bolts through flange of the enclosure and into the bracket,
tightening bolts with a 7/16” hex socket (Fig. 7, pg. 7).
6. Tighten the straps of the bottom bracket down by sliding the open end of the strap through the locking
mechanism on the strap, then tighten screw with flat head screwdriver or 5/16” hex socket driver
(Fig. 7, pg. 7).
7. Clip excess straps.
Fig. 6 Fig. 7 Fig. 8
Fig. 9
Fig. 10
2” to 8”(50.8mm to 203.2mm)
diameter round pole
Fig. 10a
5” (127mm) square pole

- 8 - WayPoint AC Series Installation Guide
Enclosure Dimensions (H x W x D approximate):
13.31” x 11.31” x 5.59” (338.1mm x 287.3mm x 142mm)
5.59” (142mm)
PADLOCK LATCH ATTACHED
WITH RIVETS (Ø 0.375” (9.5mm) PADLOCK EYE)
Ø 0.32 (8.1mm)
MOUNTING HOLE
TYP. 4 PLACES
8.00” (203.2mm)
STAINLESS STEEL PIANO HINGE
10.75” (273.1mm)
10.00” (254mm)
8.25” (209.6mm)
10.25” (260.4mm)
12.00” (304.8mm)
13.50” (342.9mm)
10-32 X 0.25” (6.4mm)
BRASS INSERT (X2)
1.61” (40.9mm)
3.96” (100.6mm)
12.75” (323.9mm)
11.31” (287.3mm)
13.31” (338.1mm)
10-32 X 0.375” (9.5mm)
BRASS INSERT (X4)
FRONT VIEW
FRONT VIEW COVER REMOVED
RIGHT SIDE VIEW
END VIEW
Altronix is not responsible for any typographical errors.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
140 58th Street, Brooklyn, New York 11220 USA | phone: [phone] | fax: [phone]
website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty
IIWayPoint AC Series I10U MEMBER