Alu-Cab SH-BKT-GEN3/CC User manual

Shower Cube
to
Gen 3 Tent & Canopy Camper DC
(SH-BKT-GEN3/CC)

2
1. Shower Cubicle Fitment – Tools, Fasteners & Materials
The tables below show the equipment, i.e. tools and fasteners required to start the
shower cubicle fitment onto a Gen 3 Tent.
1.1. Tools & Items Required:
ITEM
Turpentine
Cloth
Black sealant, silicone or Sikaflex
1.2. Fasteners supplied: (Included with Shower Cubicle)
ITEM
QTY
HEX HEAD BOLT M8X20
6
M8 FLAT WASHER
16
M8 NYLOC NUT
10
M8 PLASTIC NUT CAP
10
1.3 Hardware Required: (Included with Shower Cubical)
ITEM
DESCRIPTION
QTY
SHOWER CUBICLE
SHOWER CUBICLE ASSEMBLY
1
SHOWER CUBICLE BAG
BLACK SHOWER CUBICLE BAG
1
SHOWER CURTAIN
GREY SHOWER CURTAIN
1
FRONT MOUNT BRACKET
AWN-BKT-02-001
1
FRONT MOUNT BACK PLATE
AWN-BKT-02-002
1
FRONT MOUNT BACK PLATE
AWN-BKT-02-003
1
GENERIC MOUNTING BRACKET
415-GENE-MNT-BKT-01-00
1
BACK PLATE FOR GENERIC BRACKET
415-SHW-MNT-BCK-PLT-03
1
TOOLS
Ratchet
13mm Socket
13mm Ring Flat Spanner
Drill
Drill Bit Ø8.5

3
Fig 3. AWN-BKT-02-002
Fig 6. AWN-BKT-02-003
Fig 1.SHOWER CUBICLE
Fig 2. AWN-BKT-02-001
Fig 4. 415-SHW-GENE-MNT-BKT-01-00
Fig 5.415-SHW-MNT-BCK-PLT-03

4
2. Mounting the front mounting bracket to Gen 3 tent
Remove the mattress from the tent. Place the front mounting bracket (AWN-BKT-02-001)
to the front corner of Gen 3 tent. Keep bracket to top edge of tent base. See Fig. 7.
Use the front mounting bracket(AWN-BKT-02-001) as drill jig and drill the two holes
into the tent base. See Fig. 8.
When mounting a
bracket use Sika flex
between the plates for
sealing purposes
Fig 7: Front Bracket Position
Figure 8: Front mount hole
Drill holes
AWN-BKT-02-001

5
Mount the front mounting bracket to the tent base. Place backing plate on inside of
tent and fix with bolts, washers and nuts supplied. See Fig. 9.
When mounting a
bracket use sika flex
between the plates
for sealing purposes
AWN-BKT-02-002 FITS BEHIND THIS FRONT MOUNTING BRACKET AS SEEN BELOW
Figure 11: Front Mount Bolt Assembly
HEX HEAD BOLT M8X20
WASHER M8
NYLOC NUT M8
When mounting a
bracket use Sika flex
between the plates
for sealing purposes
AWN-BKT-02-002
Figure 9.
Figure 10.
AWN-BKT-02-002
AWN-BKT-02-003

6
3. Mounting the rear mounting bracket to Gen 3 tent
Generic mounting bracket mounts over the cargo rail on side of tent. Place Rear
Mounting Bracket (415-SHW-GENE-MNT-BKT-01-01) flush with the top edge of tent
base. See Fig. 12.
Slide the rear mounting bracket to measurement of 874mm from front mounting
bracket as seen in Fig. 14.
Rear Mount Assembly Placement
Figure 12.
M8x20mm bolts
Figure 13.
Figure 14.
874mm

7
Use the bracket as the drill jig and drill the two holes into the tent base. See Fig.15.
Mount rear mounting bracket to tent base by placing the backing plate inside the tent
then the bolts, washers and nuts. Tighten the bracket to the tent base. See Fig. 17.
Place M8 Plastic Nut Caps on all M8 Nyloc Nuts to finish of the mounting bracket
fitment.
Figure 15:Rear Mount Position
Drill holes

8
4. Mounting the shower cubicle
Place shower cubicle assembly with the bag on mounting brackets and secure shower
cubicle to the mounting brackets using the same nuts that where removed in fig 19 See
Fig. 19 & 20.

9
5. Mount Shower Cubicle on LHS of Gen 3 Tent
To mount the Shower cubicle on the Gen 3 Tent or Canopy Camper Double Cab on
LHS side, repeat procedure as for RHS. The front mounting bracket (AWN-02-001) can
be use by just turning it upside down. For the Rear Mounting Bracket (415-SHW-GENE-
MNT-BKT-01-00) This bracket is generic and can be used as is on any side of the tent.