Alula RE603P Instruction Manual

RE603P Wearable Action Button
Instructions and User Manual
1. Specifications
Frequency: 433 MHz
Operating Temperature: 32° – 110°F (0° – 43°C)
Operating Humidity: 0 – 95% RH non-condensing
Battery: 1x CR2032 Panasonic Lithium 3V DC
Battery Life: 5 Years
Compatibility: Alula receivers
Supervisory Interval: Approximately 60 minutes
2. Package Contents
1 x Wearable Action Button 1 x Rope Necklace
1 x Wrist Band 1 x Pendant Inserts (2 pcs set)
1 x Belt Clip Adapter 1x Surface Mount Bracket (w/2 screws)
1 x Manual 1 x CR2032 battery (installed)
3. Component Identification
4. Product Configuration
The RE603P can be worn or mounted in four (4 ways):
1. On a wrist using a compatible wrist band (the color of the included wrist
band may vary).
2. Around the neck as a pendant using the included pendant inserts and
snap-closure adjustable-length rope necklace (color may vary).
3. Mounted to a flat surface with the surface mount bracket and screws.
4. Worn on a belt with the surface mount bracket plus belt clip.
Note: The Surface Mount / Belt Clip accessory kit is not included and sold
separately. Compatible with any Apple Watch®-compatible wristbands.
5. Enrolling
The RE603P Wearable Action Button supports up to three (3) different
alerts or commands to be triggered through different button presses.
The button appears as three sensor zones, each with their own unique
SN. The learn activity should be repeated for each Zone / SN.
When enrolling the device, it is recommended to name each zone for
easy identification and assignment to the intended action or scene.
Example: zone #1 = “PB1 ST” (Wearable Action Button #1 single tap),
zone #2 = “PB1 DT” (Wearable Action Button #1 double tap), and zone #3
= “PB1 PH” (Wearable Action Button #1 press and hold).
To enroll the sensor, set your panel into program mode. Then go to the
Learn Sensors menu. Refer to your specific alarm panel instruction
manual for details on these menus.
To enter enrollment mode on the button, follow these steps:
1. To initiate Learn Mode, Press and Hold the Wearable Action
Button for twenty (20) seconds. During this hold time, the LED
will blink three times, then remain on for 3 more seconds [Zone
3]. Do not release the button, continue holding down the button
until the LED blinks five (5) times indicating learn mode is
enabled.
2. In learn mode, press the Wearable Action Button pattern for the
desired Zone.
Zone 1
Single Tap
Press and Release (Once)
Zone 2
Double Tap
Press and Release
(Twice, <1 second apart)
Zone 3
Press and Hold
Press and Hold (5 seconds)
Then release
3. Repeat the Wearable Action Button learn transmissions until the
panel recognizes the desired Zone’s serial number.
Important: After the zone is recognized by the panel, be sure to assign a
zone type that is “chime only”. Otherwise, the button zone will be
treated like a Door/Window open and restore and may trigger an alarm
state.
Note: Learn mode on the Wearable Action Button will automatically end
after 15 seconds of inactivity (no button press). Re-initiate learn mode as
needed until all zones are recognized by the panel.
6. Wearable Action Button Testing
The Wearable Action Button is designed to be used within 100 ft. (30 m) of the
panel. Test before first use, as well as weekly. The test verifies proper
communication between the sensor and the panel/receiver.
To test the Wearable Action Button after enrollment, refer to the specific
panel/receiver documentation to place the panel into sensor test mode.
Press the button sequence for each zone to be tested, from location(s) the
Wearable Action Button shall be used. Verify the transmission count
received on the panel is consistently 5 of 8 or better.
7. Product Operation
The RE603P Wearable Action Button supports up to three (3) different
alerts or commands to be triggered through different button presses.
The button appears as three sensor zones, each with their own unique
SN, as shown:
LED Ring
Wearable Action Button
Button
Pendant Inserts
(Top / Bottom)
Rope Necklace
Wrist Band (Top and Bottom)
CR2032 Battery
Surface Mount / Belt Clip

Zone 1
Single Tap
Press and Release
(Once)
Zone 2
Double Tap
Press and Release
(Twice, <1 second
apart)
Zone 3
Press and Hold
Press and Hold (5 seconds)
Then release
The LED Ring blink patterns confirm each button press type detected:
Zone 1
Single Tap
One short blink +
On for 3 seconds
Zone 2
Double Tap
Two short blinks +
On for 3 seconds
Zone 3
Press and Hold
Three short blinks +
On for 3 seconds
The LED will remain on for approximately 3 seconds when transmitting.
Wait until the LED is OFF before attempting the next button press.
A Zone event transmission is sent as an Open immediately followed by a
Restore. Depending on the security panel’s features, triggering each of
the Wearable Action Button’s Zones can be set up as the initiating action
to trigger a pre-configured automation or rule. Refer to your specific
panel’s instructions for more information.
8. Maintenance - Replacing the Battery
When the battery is low, a signal will be sent to the control panel.
To replace the battery:
•Insert a plastic pry tool, or a small flat blade screwdriver into one of the
notches on the back of the Wearable Action Button and gently pry to
release the back cover from the main housing.
•Set the back cover aside, and gently remove the circuit board from the
housing.
•Remove the old battery and insert a new Panasonic CR2032 battery with
the positive side (+) of the battery touching the battery holder marked
with the (+) symbol.
•Re-assemble by placing the circuit board into the back case with the
battery side facing down. Align the small notch on the side of the circuit
board with the tallest plastic rib on the inside wall of the back case. When
properly inserted, the circuit board will sit level inside back case.
•Align the arrows of back cover and the main housing, then carefully snap
them together.
•Test the Wearable Action Button to ensure proper operation.
WARNING: Failure to follow these warnings and instructions can lead to heat
generation, rupture, leakage, explosion, fire, or other injury, or damage. Do
not insert the battery into the battery holder wrong side up. Always replace
the battery with the same or equivalent type (see Specifications on page 1).
Never recharge or disassemble the battery. Never place the battery in fire or
water. Always keep batteries away from small children. If batteries are
swallowed, promptly see a doctor.
Always dispose and/or recycle used batteries in accordance with the
hazardous waste recovery and recycling regulations for your location. Your
city, state, or country may also require you to comply with additional
handling, recycling, and disposal requirements.
Product Warnings and Disclaimers
WARNING: CHOKING HAZARD - Small parts. Keep away from children.
WARNING: STRANGULATION AND CHOKING HAZARD – A user can suffer serious
personal injury or death if the cord becomes entangled or stuck on objects.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a different circuit from the receiver
• Consult the dealer or an experienced radio/TV contractor for help.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tothe
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation ofthe device.
C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est
soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas provoquer d'interférences, et(2) c’et
appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de ladispositif.
FCC ID: XQC-WST130 IC: 9863B-WST130
Trademarks
Apple Watch is a registered trademark ofApple Inc.
All trademarks, logos and brand names are the property oftheir respective owners. All
company, product and service names used in this document are for identification purposes only.
Use of these names, trademarks and brands does not imply endorsement.
Warranty
Ecolink Intelligent Technology Inc. warrants that for a period of2 years from the date of
purchase that this product isfree from defects in material and workmanship. This warranty does
notapply todamage caused by shipping orhandling, ordamage caused by accident, abuse,
misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions or
asa result ofany unauthorized modifications. Ifthere is a defect in materials and workmanship
under normal use within the warranty period Ecolink Intelligent Technology Inc. shall, atits
option, repair orreplace the defective equipment upon return of the equipment tothe original
point ofpurchase. The foregoing warranty shall apply only tothe original buyer, and is and shall
be in lieu of any and all other warranties, whether expressed or implied and of all other
obligations orliabilities on the part ofEcolink Intelligent Technology Inc. neither assumes
responsibility for, norauthorizes any other person purporting toact on its behalf to modify or to
change this warranty, nor to assume for it any other warranty or liability concerning this
product. The maximum liability for Ecolink Intelligent Technology Inc. underall circumstances for
anywarranty issue shall belimited toa replacement ofthe defective product. Itis
recommended that the customer check their equipment on a regular basis for proper operation.
Ecolink isa trademark owned by Ecolink Intelligent Technology Inc.
RE603P Designed and manufactured by Ecolink Intelligent Technology Inc. 2023.
© 2023Ecolink
PN: 47007-00xxxxx
REV &REV Date: A0201/12/2023
2055 Corte Del Nogal
Carlsbad, CA 92011
1
-855-632-6546
www.discoverecolink.com
© 2023 Ecolink Intelligent Technology Inc.