Amana LG4219*2 User manual

Service
Home Laundry Dryers
Models and manufacturing
numbers in this manual are
shown on pages 4 and 5.
This manual is to be used by qualified appliance
technicians only. Amanadoesnotassumeany
responsibility for property damage or personal
injury for improper service procedures done by
an unqualified person. RS3200001
Revision 3
(502992R3)
December 1996
Service Manual for
Amana®

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
1RS3200001 (502992R3)
Rev. 3
Failure to install, maintain, and/or operate this product according to the manufacturer's
instructions may result in conditions which can produce serious injury, death and/or
property damage.
Do not repair or replace any part of the product or attempt any servicing unless
specifically recommended or published in this Service Manual and that you understand
and have the skills to carry out.
Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the product is properly grounded and to reduce the risk of
fire, electric shock, serious injury, or death.
W009
aWARNING
W006R1
Repairs that are made to your products by unqualified persons can result in hazards due
to improper assembly or adjustments subjecting you, or the inexperienced person
making such repairs, to the risk of serious injury, electrical shock, or death.W007
aWARNING
If you or an unqualified person perform service on your product, you must assume the
responsibility for any personal injury or property damage which may result. The
manufacturer will not be responsible for any injury or property damage arising from
improper service and/or service procedures.W008
aCAUTION
NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to cover
all possible conditions and situations that may occur. It must be understood that common sense, caution
and carefulness are factors which CANNOT be built into these products. These factors MUST BE supplied
by the person(s) installing, maintaining or operating the product.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you
do not understand.
In order to locate an authorized service agency, contact the dealer from whom you purchased this product or:
Consumer Affairs Dept. or1-800-628-5782
2800 220th TrailCALL and ask for the
P.O. Box 8901Consumer Affairs Department
Amana, Iowa 52204-0001
Users of products outside of the United States and Canada should contact:
INTERNATIONAL DIVISION
AMANA REFRIGERATION, INC.
2800 220th TRAIL
P.O. BOX 8901
AMANA, IOWA 52204-0001, USA
Telephone: [phone]
Facsimile: [phone]
Recognize Safety Symbols, Words and Labels
aDANGER —Immediate hazards which WILL result in serious injury or death.
aWARNING — Hazards or unsafe practices which COULD result in serious injury
or death.
aCAUTION — Hazards or unsafe practices which COULD result in minor or
moderate injury or product or property damage.
Copyright 1996, Raytheon Appliances
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the written
permission of the publisher.

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
2
RS3200001 (502992R3)
Rev. 3
Table of Contents
30. Motor and Exhaust Assembly..........................27
31. Cabinet Top......................................................30
32. Cylinder Light ...................................................31
33. Cylinder Light Receptacle................................31
34. Front Bulkhead Assembly................................32
35. Moisture Sensor ...............................................33
36. Cylinder Belt.....................................................34
37. Cylinder Assembly ...........................................35
38. Rear Seal .........................................................36
39. Cylinder Rollers................................................38
40. Outlet Cover .....................................................38
41. Rear Bulkhead and Heater Box ......................39
42. Terminal Block or Power Cord ........................41
43. Terminal Block Terminals ................................43
44. Cabinet .............................................................43
45. Base..................................................................45
SECTION III — Adjustments
46. Leveling Legs ...................................................46
47. Burner Flame ...................................................47
SECTION IV — Test Procedures
48. Drive Motor.......................................................49
49. Burner System Operation ................................52
50. Electrical Circuit to Ignition System.................53
51. Gas Valve Coils ...............................................54
52. Sensor ..............................................................55
53. Igniter................................................................55
54. Temperature Switch .........................................55
55. Door Switch ......................................................56
56. Signal Control...................................................56
57. Timer Contact Points .......................................56
58. Cycling or Limit Thermostat.............................56
59. Thermostat Heater ...........................................58
60. Thermal Fuse ...................................................59
61. Heater Assembly..............................................59
SECTION V — Service Helps
62. Motor Does Not Run ........................................60
63. Unit Stops in Cycle; Quits after a Couple
Loads; Has a Burning Smell; Cycles on
Motor Thermal Protector ..................................61
64. Motor Runs But Cylinder Does Not Turn ........61
65. Motor Does Not Stop .......................................62
Nameplate Location ................................................4
Model Identification.................................................4
SECTION I — Grounding
1. Motor Mounting Bracket to Motor ......................6
2. Neutral at Terminal Block to Rear Bulkhead
and from Rear Bulkhead to
Control housing ..................................................7
3. Power Cord to Rear Bulkhead and from Rear
Bulkhead to Control Housing.
Wall Receptacle Polarity Check ........................7
4. From Rear Bulkhead to Timer Mounting
Bracket to Dryer Cabinet Top.
Timer Mounting Bracket to Graphic Panel........8
From Rear Bulkhead to Dryer Cabinet Top
to Electronic Control to Graphic Panel..............8
SECTION II — Service Procedures
5. Control Hood Assembly .....................................9
6. Fluorescent Light Assembly ..............................9
7. Control Hood End Caps.....................................9
8. Graphics Panel.................................................10
9. Timer ................................................................10
10. Temperature Switch .........................................10
11. Signal Control...................................................10
12. Printed Circuit Board ........................................10
13. Electronic Control.............................................10
14. Lint Filter...........................................................15
15. Inner and Outer Door Panels
and Door Pull ...................................................16
16. Loading Door....................................................16
17. Door Strike .......................................................19
18. Door Seal .........................................................19
19. Front Panel and Panel Seal ............................20
20. Door Switch ......................................................20
21. Strike Catch......................................................20
22. Door Hinge .......................................................22
23. Hold-Down Clips and Guide Lugs ...................22
24. Burner System Components............................23
25. Burner Housing and Heat Shroud ...................25
26. Limit Thermostat ..............................................25
27. Heating Element...............................................25
28. Thermister or Thermostat and Heater .............26
29. Front Air Duct...................................................26

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
3RS3200001 (502992R3)
Rev. 3
66. Heating Assembly Does Not Heat
or Burner Does Not Ignite ...............................62
67. Igniter Does Not Glow .....................................63
68. Burner Ignites and Goes Out Repeatedly.......63
69. Igniter Glows But Burner Does Not Ignite.......63
70. Heater Assembly or Burner Shuts
Off Prematurely ................................................64
71. Heater Assembly or Burner Repeatedly
Cycles Off On Limit Thermostat ......................64
72. Heater Assembly or Burner Does Not
Shut Off ............................................................65
73. Clothes Do Not Dry..........................................65
74. Timer Does Not Advance in
Automatic Cycle ...............................................66
75. Clothes Are Too Hot When Removed
From Dryer .......................................................66
SECTION VI — Internal Wiring of Dryer Motor
Switch ..............................................................67
SECTION VII — Service Procedures Unique
to the Electronic Control
Model Dryers
76. Electrical Service .............................................68
77. Grounding Instructions.....................................74
78. Failure Symptoms ............................................75
79. Blown Fuse or Tripped Circuit Breaker...........77
80. Control Will Not Wake Up (No LED’s Light)
After SELECT CYCLE Pad is Pressed ...........78
81. Control Wakes Up (When SELECT CYCLE
Pad is Pressed (But Motor Does Not
Start).................................................................79
82. Heater Does Not Turn On or No Heat ............80
83. Improper Drying Temperature
or Dry Times ....................................................81
84. “oP” Appears in Time Display .........................83
85. “SH” Appears in Time Display.........................84
86. Dryer Goes Into Cool-Down in About
Five Minutes and Load is Not Dry...................85
87. Control Replacement .......................................86
Electronic Control Board Replacement Report ......87
SECTION VIII — Service Procedures Unique to
the Electromechanical Dryers with Moisture
Sensor
88. Dryer Operation................................................88
89. Automatic Cycles .............................................88
90. No Heat ............................................................88
91. Time Dry...........................................................88
92. Control Replacement .......................................89
93. Timer Contract Points ......................................90
94. Temp/Dryness Control Resistance Chart........91
95. Timer Does Not Advance ................................92
96. Heater Does Not Turn On or No Heat ............93
97. Heater Assembly or Burner
Shuts Off Prematurely .....................................94
98. Clothes are Too Hot When
Removed From Dryer ......................................95
SECTION IX — Wiring Diagrams .........................96

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
4
RS3200001 (502992R3)
Rev. 3
Nameplate Location
Model Identification
Information in this manual is applicable to these dryer models:
P. Painted
S.S. Stainless Steel
U.P. Unpainted
Model
Number Manufacturing Number Timer Model Electronic Model Cylinder Electric Heat Gas Heat Moisture Sensor
CE4317L2 PCE4317L2 XP.X
CE4317W2PCE4317W2XP.X
CE8317W2PCE8317W2XP.X
CE8407W2PCE8407W2XP.X
CE8517W2PCE8517W2XS.S.X
CE9207W2PCE9207W2XS.S.X X
CG8409W2PCG8409W2XP.X
LE4207L2 PLE4207L2 XP.X
LE4217*2PLE4217*2XP.X
LE4207W2PLE4207W2XP.X
LE4317L2 PLE4317L2 XP.X
LE7101LB PLE7101LBXP.X
LE7101WB PLE7101WBXP.X
LE7111LB PLE7111LBXP.X
LE7111LMPLE7111LMXP.X
LE7111WB PLE7111WBXP.X
LE7111WMPLE7111WMXP.X
LE7121LMPLE7121LMXP.X
LE7121WMPLE7121WMXP.X
LE7153LB PLE7153LBXS.S.X
LE7153LMPLE7153LMXS.S.X
LE7153WB PLE7153WBXS.S.X
LE7153WMPLE7153WMXS.S.X
LE7163LMPLE7163LMXS.S.X
LE7163WMPLE7163WMXS.S.X
LE8107*2PLE8107*2XU.P.X
LE8207*2PLE8207*2XP.X
LE8207*3PLE8207*3XP.X
LE8217*2PLE8217*2XP.X
LE8317L2 PLE8317L2 XP.X
LE8317W2PLE8317W2XP.X

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
5RS3200001 (502992R3)
Rev. 3
Model
Number Manufacturing Number Timer Model Electronic Model Cylinder Electric Heat Gas Heat Moisture Sensor
LE8407L2 PLE8407L2 XP.X
LE8407W2PLE8407W2XP.X
LE8457L2 PLE8457L2 XP.X
LE8457W2PLE8457W2XP.X
LE8517L2 PLE8517L2 XS.S.X
LE8517W2PLE8517W2XS.S.X
LE8607L2 PLE8607L2 XS.S.X
LE8607W2PLE8607W2XS.S.X
LE9207L2 PLE9207L2 XS.S.X
LE9207W2PLE9207W2XS.S.X
LG4209L2 PLG4209L2 XP.X
LG4209W2PLG4209W2XP.X
LG4219*2PLG4219*2XP.X
LG4319L2 PLG4319L2 XP.X
LG4319W2PLG4319W2XP.X
LG8101LB PLG8101LBXP.X
LG8101WB PLG8101WBXP.X
LG8109*2PLG8109*2XU.P.X
LG8111LB PLG8111LBXP.X
LG8111LMPLG8111LMXP.X
LG8111WB PLG8111WBXP.X
LG8111WMPLG8111WMXP.X
LG8121LMPLG8121LMXP.X
LG8121WMPLG8121WMXP.X
LG8153LB PLG8153LBXS.S.X
LG8153LMPLG8153LMXS.S.X
LG8153WB PLG8153WBXS.S.X
LG8153WMPLG8153WMXS.S.X
LG8163LMPLG8163LMXS.S.X
LG8163WMPLG8163WMXS.S.X
LG8209*2PLG8209*2XP.X
LG8209*3PLG8209*3XP.X
LG8219*2PLG8219*2XP.X
LG8319L2 PLG8319L2 XP.X
LG8319W2PLG8319W2XP.X
LG8409L2 PLG8409L2 XP.X
LG8409W2PLG8409W2XP.X
LG8459L2 PLG8459L2 XP.X
LG8459W2PLG8459W2XP.X
LG8519L2 PLG8519L2 XS.S.X
LG8519W2PLG8519W2XS.S.X
LG8609L2 PLG8609L2 XS.S.X X
LG8609W2PLG8609W2XS.S.X X
LG9209L2 PLG9209L2 XS.S.X X
LG9209W2PLG9209W2XS.S.X X
P. Painted
S.S. Stainless Steel
U.P. Unpainted

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
6
RS3200001 (502992R3)
Rev. 3
1. MOTOR MOUNTING BRACKET TO MOTOR (Gas and Electric Models —Figure 1).
Figure 1
aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
SECTION I
Grounding

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
7RS3200001 (502992R3)
Rev. 3
Figure 3
3. POWER CORD TO REAR BULKHEAD AND FROM REAR BULKHEAD TO CONTROL HOUSING. WALL
RECEPTACLE POLARITY CHECK (Gas Models Only — Figure 3).
2. NEUTRAL AT TERMINAL BLOCK TO REAR BULKHEAD AND FROM REAR BULKHEAD TO
CONTROL HOUSING (Electric Models Only — Figure 2).
Figure 2
Canadian Models
U.S. Models

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
8
RS3200001 (502992R3)
Rev. 3
Figure 4
4. FROM REAR BULKHEAD TO TIMER MOUNTING BRACKET TO DRYER CABINET TOP. TIMER
MOUNTING BRACKET TO GRAPHIC PANEL (Mechanical Timer Model Dryers — Figure 4).
FROM REAR BULKHEAD TO DRYER CABINET TOP TO ELECTRONIC CONTROL TO GRAPHICS
PANEL (Electronic Control Model Dryers — Figure 4).

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
9RS3200001 (502992R3)
Rev. 3
SECTION II
Service Procedures
aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
IMPORTANT: When reference to direction (right or left) is made in this manual, it is from the operator’s
position facing the front of the dryer.
5. CONTROL HOOD ASSEMBLY
(Figures 5, 6, 7 and 8)
a. Remove three screws holding control hood
assembly to control hood rear panel.
b. Rotate assembly forward to access inner
wiring.
c. Disconnect wiring from inner components and
carefully remove components from control
hood assembly.
NOTE: Refer to appropriate wiring diagram when
rewiring component parts.
d. Rotate control hood assembly forward and lift
to free assembly from hold-down clips.
6. FLUORESCENT LIGHT ASSEMBLY (Models
containing fluorescent light only)
(Figures 6 and 7)
a. Remove three screws holding top cover to
control mounting plate. Rotate top cover
forward to release front edge of top cover
from top edge of diffuser, Figures 5, 6, 7 and
8.
b. Disconnect two wires from rocker switch
(located in diffuser).
c. Disconnect wires at disconnect blocks located
in control mounting plate.
d. Remove two screws holding fluorescent light
to control mounting plate.
e. Lift fluorescent light out of control mounting
plate.
7. CONTROL HOOD END CAPS
(Figures 5, 6, 7 and 8)
a. Remove three screws holding control hood
assembly to control hood rear panel.
b. Rotate assembly forward to access inner
wiring.
c. Disconnect wiring from inner components and
carefully remove components from control
hood assembly.
NOTE: Refer to appropriate wiring diagram when
rewiring component parts.
d. Remove two screws holding end cap to end
of mounting plate.
e. Carefully pry end cap from control mounting
plate and control panel.
NOTE: To re-assemble reverse the steps.

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
10
RS3200001 (502992R3)
Rev. 3
8. GRAPHICS PANEL
(Figures 5, 6, 7 and 8)
a. Remove three screws holding control hood
assembly to control hood rear panel.
b. Rotate assembly forward to access inner wiring.
c. Disconnect wiring from inner components and
carefully remove components from control
hood assembly.
NOTE: Refer to appropriate wiring diagram when
rewiring component parts.
d. Remove three screws holding top cover to
mounting plate. Rotate top cover forward to
release front edge of top cover from top edge
of diffuser, Figure 5, 6, 7 and 8.
e. Carefully remove two control knobs and timer
knob by pulling forward.
f. Remove screws holding end caps to mounting
plate and pry caps off mounting plate.
g. With graphics panel facing forward, rotate
control hood assembly forward to access tabs
holding graphics panel.
h. Bend graphics panel tabs until straight and
pull panel away from control mounting plate.
NOTE: To re-assemble reverse the steps.
9. TIMER
(Figures 5, 6 and 8)
a. Remove the three screws holding the control
assembly to the control hood rear panel,
Figures 5, 6 and 8.
b. Rotate assembly forward to access inner wiring.
c. Disconnect wiring from inner components and
carefully remove components from control
hood assembly.
NOTE: Refer to appropriate wiring diagram when
rewiring component parts.
e. Remove two screws holding timer to mounting
plate.
f. Remove knobs.
10.TEMPERATURE SWITCH
(Not included in electronic control models)
(Refer to Figures 5, 6 and 8)
a. Remove three screws holding control hood
assembly to control hood rear panel.
b. Rotate assembly forward to access inner
wiring.
c. Disconnect wiring from inner components and
carefully remove components from control
hood assembly.
NOTE: Refer to appropriate wiring diagram when
rewiring component parts.
d. Remove nut holding temperature switch to
control mounting plate.
e. Remove two screws holding temperature
switch bracket (if separate from temperature
switch) to control mounting plate.
f. Using a needle nose pliers, press in on
locking tabs holding temperature switch to
control mounting plate.
g. With locking tabs pressed in, rotate
temperature switch counterclockwise 1/4 turn
and remove switch out rear of control
mounting plate.
11.SIGNAL CONTROL
(Figures 5, 6 and 8)
a. Remove three screws holding control hood
assembly to control hood rear panel.
b. Rotate assembly forward to access inner
wiring.
d. Disconnect wires to the signal control.
NOTE: Refer to appropriate wiring diagram when
rewiring component parts.
e. Remove signal control knob.
f. Remove two screws holding the signal control
to the control mounting plate.
12.PRINTED CIRCUIT BOARD
(Models with Moisture Sensor Only)
a. Remove three screws holding control hood
assembly to control hood rear panel.
b. Rotate assembly forward to access inner
wiring.
c. Pull printed circuit board forward to slide off
plastic support pegs.
13.ELECTRONIC CONTROL
(Figure 7)

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
11 RS3200001 (502992R3)
Rev. 3
Figure 5
GRAPHIC PANEL, CONTROL HOOD AND CONTROLS
(Models LE7111*M, LG8111*M, LE8317*2, LG8319*2, LE4317*2, LE8407*2, LE8567*2,
LE8517*2, LG4319*2, LG8409*2, LG8459*2, LG8569*2, LG8519*2, CE4317*2,
CE8407*2, CE8517*2, CG8409*2, LE7111*B, LG8111*B and LE8457*2)
* Is for the color designator, “L” indicates ALMOND and “W” indicates WHITE color.

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
12
RS3200001 (502992R3)
Rev. 3
Figure 6
GRAPHIC PANEL, CONTROL HOOD AND CONTROLS
(Models LE7163*M and LG8163*M)
* Is for the color designator, “L” indicates ALMOND and “W” indicates WHITE color.

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
13 RS3200001 (502992R3)
Rev. 3
Figure 7
GRAPHIC PANEL, CONTROL HOOD AND CONTROLS
(Models LE9207*2, LG9209*2 and CE9207*2)
* Is for the color designator, “L” indicates ALMOND and “W” indicates WHITE color.

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
14
RS3200001 (502992R3)
Rev. 3
Figure 8
GRAPHIC PANEL, CONTROL HOOD AND CONTROLS
(Models LE8207*3, LG8209*3, LE8207*2, LG8209*2, L34217*2, LG4219*2, LE8217*2, LG8219*2,
LE8107*2, LG8109*2 LE4207*2, LE8607*2, LG4209*2, LG8609*2, LE7101*B, LG8101*B, LE7121*M,
LG8121*M, LE7153*M, LE7153*B, LG8153*M and LG8153*B)
* Is for the color designator, “L” indicates ALMOND and “W” indicates WHITE color.

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
15 RS3200001 (502992R3)
Rev. 3
Figure 9
14.LINT FILTER (Figure 9)
a. Open loading door.
b. Remove lint filter screws.
c. Lift lint filter cover out of lint filter.
d. Lift lint filter out of air duct.
aWARNING
When installing lint filter, be sure to
install the filter with the word “FRONT”
facing the front of the dryer. If filter
is installed backwards, lint will
accumulate in exhaust system,
increasing the risk of fire and machine
malfunction.

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
16
RS3200001 (502992R3)
Rev. 3
15.INNER AND OUTER DOOR PANELS AND
DOOR PULL
a. Remove four screws holding door assembly to
hinges, Figure 9.
b. Remove screw from door pull, Figure 11, and
the remaining screws around the door
perimeter and separate panels, Figure 11.
NOTE: All screws are interchangeable except for
the screw in the recessed door pull.
IMPORTANT: Do not over-tighten screws when
reinstalling door pull.
16.LOADING DOOR
a. Open loading door.
b. Remove screws holding loading door to
hinges, Figure 9.
REVERSING DOOR PROCEDURE
The door on this dryer is completely reversible. To reverse door proceed as follows:
Figure 10 Figure 11
Figure 12 Figure 13

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
17 RS3200001 (502992R3)
Rev. 3
Figure 14 Figure 15
Figure 16 Figure 17
Figure 18

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
18
RS3200001 (502992R3)
Rev. 3
Figure 19

aWARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryerbefore servicing.
• Close gas shut-off valve to gas dryer before servicing.
• Never start the dryer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.W001
19 RS3200001 (502992R3)
Rev. 3
Figure 20
17.DOOR STRIKE
a. Open loading door.
b. Remove screw holding door strike and
bracket to loading door, Figure 19, and
remove strike and bracket.
NOTE: You may have to loosen the two screws
on end of door to allow for striker and bracket
removal.
18.DOOR SEAL
a. Open loading door.
b. Grasp either end of door seal at bottom of
door and remove seal from tabs on inner door
panel by gently pulling on the seal, Figure 20.
NOTE: When replacing seal, be sure seal is not
stretched or distorted and the groove in the seal
is installed on each tab on inner door panel,
Figure 20, and the split in the seal is at the
bottom of the door.