Amart Furniture ANNEKA 54582 User manual

1 54582
432MM
1200MM
390MM
Imported by Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture,
Amart Furniture
Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
ANNEKA 2 DOOR ENTERTAINMENT UNIT
ITEM CODE 54582
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture
, Customer Service Free call 1800 351 084

2 54582
to
.
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liing. Product should be assembled as near as possible
the point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucons carefully before beginning assembly
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over ghten the screws and bolts as this may damage the threads
12 1
2
3
4
5
6
7
8
9
10
11
ALLOW 60 MINUTES
TOOLS REQUIRED
PEOPLE REQUIRED
x 1
We recommend using a
screwdriver to put this item
together. However if you choose
to use a power drill it must be
used on LOW SPEED (LOW
TORQUE) as too much pressure
could damage the product

M3.5x14mm
I
Ix16
screw
M4x14mm
J
Jx20
screw
M3x16mm
K
Kx14
screw
M4x19mm
L
Lx2
M
Mx1
screw
A
Ax8
cam lock
M15x12mm
B
Bx8
dowelcam pin
M7x39mm M8x30mm
C
Cx20
3
7
4
5
6
8
9
10
1
2
3 54582
EXPLODED EXAMPLE
1
2
3
4
6
8
9
10
5
7
LEFT PARTITION PANEL
RIGHT PARTITION PANEL
SHELF PANEL
LEFT SIDE PANEL
TOP PANEL
BACK PANEL
LEFT DOOR PANEL
RIGHT DOOR PANEL
RIGHT SIDE PANEL
BOTTOM PANEL
E
Ex4
hinge
M34x160mm
F
Fx4
metal plate for legleg
G
Gx4
screw
M5x40mm
H
Hx12
handle
D
Dx2
wall fixing
M4x30mm M3.5x14mm

4 54582
CAM LOCK INSTALL METHOD AS FOLLOWS
Step 1 Step 2
OR
Step 3
Fix cam nut into
the bottom of hole
then tighten it.
Lock
1.1cm
C

5 54582
STEP 1: Insert dowel to le paron panel ,right paron
panel and shelf panel .
C 1
2 3
STEP 2: Aach shelf panel to le paron panel and right
paron panel with screws .
3 1
2 H
3
C
C
C
C
Left edge
Front veneer edge
3
1
2
H
H
H
H
Bottom edge
Left edge
Front veneer edge
1
C
C
C
C
Bottom edge
Front veneer edge
2
C
C
C
C
Bottom edge
Front veneer edge

6 54582
STEP 3: Fix cam pin to top panel .
STEP 4: Insert dowel to le side panel and right side panel .
B
C 4 5
6
6
B
B
B
B
B
B
B
B
Back edge
Left veneer edge
4 5
C
C
C
CC
C
C
C
Bottom edge Bottom edge
Front veneer edge Front veneer edge

7 54582
STEP 5: Aach top panel to paron panels and side
panels with the cam locks .
STEP 6: Fix metal plates to boom panel with screws .
G 7 J
6
4 5 A
1 2
6
4
1
2
5
A
A
A
A
A
A
A
A
Bottom edge
Bottom edge
Front veneer edge
Front veneer edge
7
J
GBack edge
Left veneer edge
J
G
7

8 54582
STEP 7: Fix legs to the metal plates .
STEP 8: Aach boom panel onto exisng unit with screws .
7 H
F 7
7
F
F
F
F
Back edge
Left veneer edge
7
4
1
2
5
H
H
H
H
H
H
H
H
Left veneer edge
Front veneer edge
Front veneer edge
Front veneer edge

9 54582
STEP 9: Fix hinges to right door panel with screws .Aach
right door panel to unit by the hings with screws .
Fix handles to right door panel with screw .
E I
E
D L
I
10
10
10
10
10
5
I
E
E
L
D
I
E
I
I
I
I
I
I
I
II
Left veneer edge
Bottom veneer edge
Bottom veneer edge
Left veneer edge
Front veneer edge
Left veneer edge
10
5
10
I
I

10 54582
STEP 10: Fix hinges to right door panel with screws .Aach
right door panel to unit by the hings with screws .
Fix handles to right door panel with screw .
E I
E
D L
I
9
9
9
9
4
9
I
I
I
I
E
E
L
D
I
II
I
Right veneer edge
Bottom veneer edge
Right veneer edge
Front veneer edge
Right veneer edge E
I
I
9
I
I
I
9
4

11 54582
If door is hinge bound, (rubbing on frame as you
close or open door) loosening screw shown and
move the door in appropriate direcon. (In or out)
Lateral Door Adjustment:
Horizontal Door Adjustment:
Rotate Screw clock wise or an clockwise.This
will produce an even gap between doors and
frame.
Vercal Door Adjustment:
Loosening both screws on all hinges and li the door
to desired height. This allows an even space at the
top and boom between door and product frame.
To Align Doors & Control Gap In Between Doors.
Product doors may need adjusng during & aer
assembly or once product contains items.
This can be done by adjusng appropriate screws.
See below illustraon.
Customer Aenon:
Important Note:
If there is a problem with the door assembly , please refer to
below important note.

STEP 12: Fix the back panel to body with screws .
ASSEMBLY COMPLETE
12 54582
8 K
8
K
K
K
K
K
K
K
K
K
K
K
K
K
K
Right veneer edge
DO NOT PUSH OR DRAG THIS FURNITURE – IT WILL CAUSE
DAMAGE TO THE LEGS

13 54582
STEP 1: Fix bracket to back panel using screws M3.5*14MM .
Put plasc string into bracket.
!
M
NOTE - This product must be fixed to a wall.
Please ensure the correct wall fixings are used.
Failure to do so may result in personal injury or
cause property damage if the product topples
over. Please note that the screws are only
suitable for plasterboard wall materials, please
contact local hardware store for corresponding
screws for other wall materials.

14 54582
STEP 2: Fix bracket onto the wall using screws M4*30MM.
Join wallboard and the furniture with plasc sng.
M
Wallboard Furniture top
Bracket
M

15 54582
SAFETY BRACKETS INSTRUCTIONS
1.Attach a bracket to the wallboard with the long screws provided.
2.Attach a bracket to the furniture frame under the top with the
short screws provided.
3.Move the furniture into its final position. Thread a strap through
the bracket as shown in the illustration, tighten strap until snug.
Do not over tighten.
4.Make sure the bracket is firmly attached to the wallboard and
furniture, and the strap is snug.
!
Wallboard Furniture top
Bracket
M

16 54582
PRODUCT CARE:
To protect your furniture,we suggest the following:
*Avoid placing your furniture in direct sunlight.
*Do not place furniture directly under windows.
*Do not place sharp materials(knife,fork,etc) directly onto your furniture as sharp
material may scrape and damage the finish.
Do not place material with high temperature directly onto the surface of your
furniture.
*Protecve padding is strongly recommended when using your furniture .
*Clean up spills quickly.Water leover a prolonged period of me may cause
damage.Alcohol,perfume,nail polishes,aershave and some medicaon may
cause severe finish damage if not cleaned immediately.
*Use a clean,so,dry,lint free absorbant cloth to clean your furniture.Do not use
NOTE: If the above care advise is not adhered to your product warranty may
become void.
any detergent as they may contain ingredients that may react and damage thefinish.