Amart Furniture Nemo 53031 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture Ewing Road, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture Ewing Road, Customer Service Free call 1800 351 084
53cm
51cm
79-89cm
Nemo office Chair
ITEM CODE:53031
1-6 53031

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean,level,spacious assembly area.Avoid hard surfaces that
may damage the product
2.Take care when lifting.Product should be assembled as near as possible to
the point of use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning
assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
ALLOW 10 MINUTES 1 PEOPLE REQUITED
ADDITIONAL TOOLS REQUIRED
2-6 53031

PARTS LIST
1 BACK
2 BAR SUPPORT
3 SEAT
4 MECHANISM
5 GAS LIFT
6
7BASE
CASTOR
4XPCS
1/4"X16mm
bolt bolt
A B
2XPCS
1/4"X25mm
C
1XPC
140×50mm
GAS LIFT COVER
8
2
3
4
1
5
6
7
8
3-6 53031
plastic cover

STEP 1: STEP 2:
8
7
6
5
4-6 53031
Insert castor (8) to base (7). Put gas lift (5) into base (7) as
instruction shown, then put gas lift
cover (6) on gas lift (5).
STEP 3:
Separate mechanism (4) as
instruction shown, then insert bar
support (2) into mechanism (4)
and connected using mechanism
spare part 4-1, 4-2,4 -3,4 -4,4 -5,
4-6,4-7.
4-8 4- 9
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4
4-1
4-2
4-3
4-4
4-5
4-6
4-7
Connect bar support (2) and back
(1) using plastic cover C and bolt B.
B
C
1
2
STEP 4:

STEP 5:
4-9 AA
A
4-8
A
3
5-6 53031
STEP 6:
Complete mechanism (4) using
4-8,4 -9.
Connect mechanism (4) and seat
(3) using bolt A.
CARE AND MAINTENANCE
DO NOT STAND ON THIS CHAIR-DO NOT USE THIS CHAIR AS STEP LADDER
USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME
DO NOT USE THIS CHAIR UNLESS ALL BOLTS, SCREWS AND KNOBS ARE
FIRMLY SECURED.
AT LEAST EVERY 4 MONTHS, CHECK ALL BOLTS, SCREWS AND KNOBS TO
BE SURE THEY ARE TIGHT.
IF PARTS ARE MISSING, BROKEN, DAMAGED OR WORN, STOP USE THE
PRODUCT UNTIL REPAIRS ARE MADE. USING FACTORY AUTHORIZED PARTS.
FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY .
OFFICE CHAIR
DO NOT REMOVE THIS LABEL
STEP 7:
Put back (3) on gas lift (5). Assembly is complete.
STEP 8:

CARE AND MAINTENANCE
DO NOT STAND ON THIS CHAIR-DO NOT USE THIS CHAIR AS STEP LADDER
USE THIS PRODUCT ONLY FOR SEATING ONE PERSON AT A TIME
DO NOT USE THIS CHAIR UNLESS ALL BOLTS, SCREWS AND KNOBS ARE
FIRMLY SECURED.
AT LEAST EVERY 4 MONTHS, CHECK ALL BOLTS, SCREWS AND KNOBS TO
BE SURE THEY ARE TIGHT.
IF PARTS ARE MISSING, BROKEN, DAMAGED OR WORN, STOP USE THE
PRODUCT UNTIL REPAIRS ARE MADE. USING FACTORY AUTHORIZED PARTS.
FAILURE TO FOLLOW THESE WARNINGS COULD RESULT IN SERIOUS INJURY.
OFFICE CHAIR
DO NOT REMOVE THIS LABEL
6-6 53031