Amart Furniture Valdis 73827 User manual

Imported by Amart Furniture Pty Ltd, ,Brisbane, Qld, Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Free call 1800 351 084
ASSEMBLY INSTRUCTION
Valdis Lamp Table
ITEM CODE 73827
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please
phone Amart Furniture , Customer Service Free call 1800 351
084
1ITEM CODE 73827
452mm

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2 ITEM CODE 73827
We recommend using a
screwdriver to put this item
together. However if you choose
to use a power drill it must be
used on LOW SPEED (LOW
TORQUE) as too much pressure
could damage the product
ALLOW 40 MINITES 2 PEOPLE REQUIRED

3ITEM CODE 73827
PARTS LIST
1
Drawer Handle
2
Support Bar
3
Top Board
4
Side Board
5
Side Board
6
Bottom Board
7
Back Board
8
Drawer Front Board
9
Drawer Side Board
10
Drawer Side Board
11
Drawer Support Barr
12
Drawer Bottom Board
13
Drawer Back Board
14
Frame
15
Frame
1
2
3
4
5
6
10
7
8
9
11
12
13
14
15
X4
X4

ITEM CODE 738274
A. Ø15X12mm
AX15 BX15 CX12
C. Ø8X40
DX6
D. M5X50
FX10
F. M3.5X15 G.
GX1
E. M4X40mm
EX5
H.
HX8
I. L350mm J. L350mm K. L350mm L. L350mm
M. M6X15mm
IX1 JX1 KX1 LX1
MX12
N.
B. M6X39mm

ITEM CODE 738275
STEP:1
STEP:2
A. Ø15X12mm
AX5 BX5
A
A
B
10
8
8
9
10
9
10
9
11
11
11
12
12
13
B
B. M6X39mm
1. Fix cam pin (B) to drawer front board (8)
2. Attach drawer side board (9)(10) drawer
support bar (11) to drawer front board (8)
with cam locks (A)
1. Put bottom board (12) into
groove of board (8)(9)and (10).
2.Put the drawer back board
(13) on the drawer.

ITEM CODE 738276
STEP:3
EX5
E. M4X40
FX4
F. M3.5X15 J. L350mm L. L350mm
JX1 LX1
L
J
F
L
J
E
E
9
10
10
13
11
11
11
10
9
9
8
8
1. Attach the drawer back board (13)
with screws (E)
2. Install runner(J)(L) to the bottom
of drawer with screws(F).

ITEM CODE 738277
STEP:4
STEP:5
H.
HX4
H
CX12
C. Ø8X40
C
H
10
9
13
8
1
1
4
5
7
Fix handle (1) to the drawer front board (8) with screws (H)
Insert dowel (C) to side board (4)(5) and back board (7)

ITEM CODE 738278
STEP:6
STEP:7
I. L350mm K. L350mm
IX1 KX1 FX6
F. M3.5X15
F
!
BX4
I
K
B
4
5
4
5
B. M6X39mm
B
Install runner(I)(K) to the side board(4) (5) with screws (F)
Fix cam pin (B) to the side board(4) (5)

ITEM CODE 738279
STEP:8
STEP:9
A
A. Ø15X12mm
AX4
A
4
5
7
H
H.
HX4
H
1
1
4
5
7
Attach the side board(4) (5) to the back board (7) with cam locks (A).
Fix handle (1) to back board (7)with screws (H)

ITEM CODE 7382710
STEP:10
STEP:11
A. Ø15X12mm
AX6
A
4
5
7
3
BX6
B
3
B
B. M6X39mm
A
Fix cam pin (B) to the top board (3)
Attach the top board (3) to the body with cam locks(A)

M
G
ITEM CODE 73827
STEP:12
STEP:13
G.
GX1
M. M6X15mm
MX4
4
6
14
DX6
D. M5X50
D
4
5
6
7
7
14
Attach the bottom board (6) to the body with the screws (D)
Attach frame (14) to the bottom board
(6) with bolt (M)

M
G
ITEM CODE 7382712
STEP:14
STEP:15
G.
GX1
M. M6X15mm
MX4
15
G.
GX1
M. M6X15mm
MX4
4
6
2
2
2
2
2
M
G
7
15
4
6
7
Fix support bar (2) to frame (14) with bolt (M)
Attach frame (16) to the body with bolt (M)
14
14

ITEM CODE 7382713
STEP:16
ASSEMBLY COMPLETE
4
3
5

14 TEM ICODE 73827
SAFETY BRACKETS INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to attach
the Mounting Plate into a stud. If mounting into brick or masonry you will need to
acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and furniture
and that the Wall Strap is snug.
HARDWARE
Mounting Plate x 2 Wall Strap x 1 Large Screw x2 Small Screw x2

15
To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto your
furniture as sharp material may scrape and damage the finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
TEM ICODE 73827