AmazonBasics B072PZBHTY User manual

created by: Impala Services Ltd.Page size: 139.7 x 107.95 mm
B072PZBHTY
Adjustable Standing Desk Converter with Keyboard Tray
Convertisseur De Bureau En Position Debout à Hauteur Réglable Avec Tiroir à Clavier
Verstellbarer Stehschreibtisch-Konverter mit Tastaturablage
Convertitore Scrivania Regolabile per lavorare In Piedi con Ripiano Tastiera
Convertidor De Escritorio Ajustable Con Bandeja El Para Teclado
高さ調整可能スタンディングデスクコンバーター、キーボードトレイ付き
可调节站立式办公桌转换台，带键盘托架

English ..................................... 3
Français ................................. 15
Deutsch.................................. 27
Italiano................................... 39
Español.................................. 51
日本語 ..................................... 63
中文 ........................................ 75

3
Welcome Guide •English
Adjustable Standing Desk Converter
with Keyboard Tray
Contents:
Before getting started, ensure the package contains the following components:
Part Qty
1
Tools Needed
Max: 30 lbs
(13.6 kg)
Max: 5 lbs
(2.27 kg)
A+B≥ 10 lbs
(4.5 kg)*
A
B
Caution: do not exceed maximum
listed weight capacity. Serious
injury or property damage may
occur!
*Prior to using the desk, please place a minimum weight of 10 lbs
(4.5 kg) on the worksurface and keyboard tray. The desk is not intended
for use without any minimum load. Otherwise, the worksurface will
rise up on its own when the brake is released.

4
Assembly
Step 1:
Setting Up the Product

5
Assembly
Step 2:
Setting Up the Product

6
Assembly
Step 3:
Setting Up the Product

7
Assembly
Step 4:
Setting Up the Product
• Caution: Keep monitor and laptop base fully on the worksurface.
Allowing any part of base or stand to hang off the edge may result in
property damage and or personal injury.

8
Assembly
Step 5:
Setting Up the Product

9
Assembly
Step 6:
Setting Up the Product
• Caution: To avoid the potential to pinch cables it is important to
follow the cable routing instructions in this manual. Failure to follow
these instructions may result in equipment damage or personal
injury.
• Caution: Leave enough slack in cable to allow for full range of
vertical motion (15” / 38 cm). Failure to heed this warning may result
in property damage and or personal injury.

10
Safety and Compliance
• Warning: Because mounting surface materials can vary widely, it is imperative that you make
sure mounting surface is strong enough to handle mounted product and equipment.
• Warning: DO NOT place hands on or near support bars. Pinch points
are created during lifting and lowering the worksurface. Failure to follow
these instructions may result in serious personal injury.
• Warning: Impact Hazard! Moving Parts can Crush and Cut. Raise this
product to its full up position before lifting off the desk.
• Two people are required to lift this product off the desk.
• Do not tip this product on its side or upside down. This product must
remain upright at all times.
• Failure to heed this warning may cause unintended motion of the lift
mechanism resulting in possible serious personal injury and or property
damage!
• Warning: Impact Hazard! Moving Parts can Crush and Cut.
• Raise worksurface to top of vertical adjustment BEFORE removing
equipment.
• Failure to heed this warning may result in serious personal injury and or
property damage!
• Caution: To avoid the potential to pinch cables it is important to follow
the cable routing instructions in this manual. Failure to follow these
instructions may result in equipment damage or personal injury.
• Caution: Leave enough slack in cable to allow for full range of vertical
motion (15” / 38 cm). Failure to heed this warning may result in property
damage and or personal injury.