American Changer AC6007 User manual

1
AMERICAN CHANGER & HOFFMAN MINT
We Are Changing the Industry℠
1400 N. W. 65th Place, Fort Lauderdale, Florida 33309
T: ([phone] F: ([phone]
www.americanchanger.com www.hoffmanmint.com
AC6007 Flex System Installation Guide (Tran Unit)
Step 1: Remove main board, relay board, and power supply.
Main Board
and Relay
Board
Figure 1

2
Step 2: Remove all harnesses inside of the cabinet except for the validator harness, hopper
harnesses, and printer harnesses.
Step3: Take the new plate with the new board, power supply and Iris Unit on it and mount it in the
same location as the old mount that was removed in the first step.
Figure 2

3
Step 5: Remove the three nuts that are holding the display in place. See Figure 3. Washers and screw
on stand-offs were supplied with the kit. Add a washer and a screw on stand-off to the studs that
previously had nuts. See Figure 4.
Display with
ribbon
harness and
keypad
harness
removed
View from
inside of
machine.
Remove nuts
from Display
Mount.
Figure 3
Display with
the washers
and screw-
on stand offs
installed
Figure 4

4
Step 6: Attach the I/O Board to the back of the display by inserting the connector on the I/O Board into
the matching connector on the display. Use supplied screws to secure the I/O Board to the stand-offs.
See Figures 5 & 6.
I/O Board
Top View
I/O Board
Bottom View
Figure5
Figure 6
Connector
Matching
Connector
on Display
Completed
Display with I/O
Board Installed

5
Step 7: Connect your marquee in to “#1” on the power board.
Harness to the
main board
Marquee
Figure 7

6
Step 8: Place the Tran Unit flat on the floor of the cabinet. Connect the beige color communication
cable, Ethernet cable/phone line, and then connect the power adaptor.
IP Tran Connections
Power
Communication
Cable
Ethernet cable
Dial Tran Connections
Communication
Cable
Phone Line
Power
Figure 8

7
Installing the External Keypad
The following steps are used to install the external keypad that came with the kit. This keypad is used to
navigate the programming menu as well as input values while in the programming menu. The external
keypad can also be used to input a zip code if zip code verification is enabled
Step 9: It is recommended to mount the keypad near the display. Place the keypad against door and
use a felt tip marker to mark your four mounting holes. You will also need to mark the area for the
harness to connect to the key pad.
Front View
Four Mounting Holes
Rear View
Connector for
Harness
Figure 9

8
Step 10: Before drilling your holes remove the hoppers from the machine. Using titanium bits drill the
holes in the door.
Step 11: Secure the keypad to the door using the supplied screws and nuts.
Step 12: Connect the harness from the I/O Board to the keypad. Connect as shown in the below
picture. If not connected properly the numbers will not be recognized correctly.
Figure 10

9
Step 13: Use the below picture to help with connecting the components to the main board.
Printer
I/O
Board
Iris
Figure 11

10
Additional steps for connecting optional adaptor boards
This section details how to connect adaptor boards to the main board. Adaptor boards are not shipped
with all orders. These boards will already have the necessary harnesses attached to them. All that will
be needed is to connect the component to the adaptor board. If you did not receive any adaptor boards
with your order then skip this section.
Step 14: Connect the hopper plate harness to the hopper adaptor board. Then connect the harness
that was already attached to the adaptor board to the main board.
Step 15: Connect the flat “ribbon” style harness from your printer to the adaptor board. Then do the
same for the power harness. Again connect the harness that is already attached to the adaptor board to
the main board.
Connect hopper plate
here.
Harness to main board
connects here.
Connect power harness
here.
Harness to main board
connects here.
Connect ribbon harness
here.
Figure 12
Figure 13