Alberici HammerOne S11 User manual

1
Operator’s Manual
HAMM
ER 1 ONE
1 HopperOne
HAMMER 1 CD
1 HopperCD
HAMMER 1 CD + CD
2 HopperCD
HammerOne S11 Money Changer
Operator
’s
manual
Rev. 1.01

2
Ogni possibile cura è stata posta nella redazione del presente manuale. Ciò
nonostante, non è possibile garantire in ogni momento la corrispondenza assoluta delle descrizioni,
in esso contenute, con le caratteristiche del prodotto.
La Alberici S.p.A. declina ogni e qualsivolglia responsabilità verso l’utilizzatore con riferimento a
danni, perdite, o reclami di terze parti, conseguenti all’uso del prodotto o causate da errate
interpretazioni del presente manuale.
Alberici S.p.A. si riserva il diritto di modificare, senza avviso, in qualunque modo qualunque parte
del presente manuale.
NOTA

3
CONTENTS
1. Package content............................................................................................................................4
2. Component names........................................................................................................................4
3. Product description ......................................................................................................................5
4. Warning........................................................................................................................................5
5. Installation....................................................................................................................................6
6. Operation......................................................................................................................................8
7. System configuration ...................................................................................................................9
8. Messages ....................................................................................................................................16
9. Maintenance of the note validator..............................................................................................17
11. Disposal of the product...............................................................................................................19
12. Terms of Guarantee ....................................................................................................................19
13. Customer Service.......................................................................................................................20
STORICO REVISIONI
Revisione n
°
Data
Modifica
Note
Creazione 16. 12.12 Creazione Nuova scheda CMS
Rev. 1.01 10.01.14 Sostituito BillyOne a Taiko, OryOne a Vega

4
Dear Customer,
we would like to thank you and congratulate for your choice. We trust that you will appreciate the
quality and performace of the HAMMER 1 automatic Change Machine.
This machine operates by cctalk protocol, the well-established serial communication mode that
provides security and precision.
1. Package content
The package contains:
1. the Alberici HAMMER 1 Change machine
2. 3 pairs of keys
3. the power cable (see inside of money box)
4. the instruction manual (this manual)
This product has been packed with the utmost care. In the case that you receive it damaged or
incomplete, please notify immediately your findings to the Carrier.
2. Component names
POS. PART #
DESCRIPTION
A AE-0804
PS Power Supply Box
B SH-1A21 ChangeOne board v. 10 CM
C LED-0101 Blue 3-led bar
D LED-0100 2 x Blue 5-led bar
E HP-E112
HP-Q134
HopperS11 ccTalk STD (HAMMER1 One)
HopperCD ccTalk Midi (HAMMER 1 CD)
F LB-LC01
(as option:
LB-MC02)
BILLYONE ccTalk note validator
(as option:
ORYONE ccTalk note validator + stacker)
G AM-1511 Cylinder lock keyed different (n. 3)
H
PL-MK21-156D 2 x Miniature square MK-21 illuminated
pushbutton, 12 V (HAMMER CD2 only)
A
B
C
D
E
F
G
Please read carefully this handbook, to obtain the most from your HAMMER 1.
H

5
3. Product description
3.1 General data
Size:
Weight:
Voltage:
Nominal power:
Operation temperature:
Installation:
Coin capacity:
Components:
Power supply unit
Control board
Display
Note validator
Pay-out Hopper
260 mm (l) x 1600 mm (h) x 376 mm (p) [480 mm at the foot]
53 Kg
230 Vac - 50 Hz
140 W max
0°C ÷ +50°C, humidity min. 20% max. 85% non condensing
wall-mount, indoor
3600 (0,50 or 1 €), 2700 (2 €)
Power switching 60 VA with anti-noise filtre, built-in cooling fan
cctalk CHANGEONE CMS version NL (no Bonus credit accumulation)
built-in LCD blue display, 2 x 16
BILLYONE , or
ORYONE ccTalk (with stacker capacity: 300 notes)
HOPPERONE S11 cctalk + extension (appr. c.ty 3600 pcs. 1 € coins )
HopperCD ccTalk Midi + extension (appr. c.ty 3600 pcs. 1 € coins)
Notice: Euro is the preset currency. If you require a different currency, please request for
availability of your currency before placing your order.
3.2 Available functions
- Change of notes into coins
- Tokens purchase with or without bonus (limitations to type of token can apply)
- Control of accounts via display (by board keys)
- Programmable via menu (by board keys)
4. Warning
- Comply with the instructions in this manual
- Switch power off before any maintenance operation
- Use only within the recommended temperature/humidity range
- Do not expose the machine (and especially the mote acceptor front plate) to direct
sun light or to incandescent light (> 3000 Lux)
- When in precence of car exhaust gas or smoke, clean and check the components (the note acceptor
in particular) regularly and frequently.
- Do not favour contact with dusts or chemical moisture or sprays, water or other liquids
- Instal indoor
- Wipe clean by a dry piece of cloth (or slightly wet with alcohol)
- Do not use thinners or organic solvents
- The note acceptor could reject (or get jammed by) stained notes, or worn out, wet, wrinkled, torn,
dog-eared, oil-smeared, with sticking tape or similarly affected.
!

6
5. Installation
5.1 Positioning and switching on
PAY ATTENTION: IT IS ESSENTIAL TO FASTEN THE MACHINE TO A
SOLID WALL BY USING EXPANSION BOLTS
Put the Change Machine in place and fasten it to the wall by tightening expansion bolts through the
holes preset in the rear side. Keep the on-off switch accessible. It is also possible to secure the
machine to the floor. The large holes at the foot allow to secure the machine by a binding chain.
Open the filling door on top and funnel the coins (or the tokens) into the hopper(s). HAMMER1
ONE and HAMMER1 CD handle one coin denomination; HAMMER1 CD+CD can handle 2.
WARNING: switch off the machine before introducing the coins!
Lock the door back, plug the power cable in and turn the on-off switch on.
The display will show that the machine is carrying out
the initial self-check and self-configuration.
A further message will inform that the machine is ready for operation, and will show what coin
(token) value will be paid in exchange for notes and coins introduced.
This message takes shifts with:
If such value does not correspond to the actual coins
funneled in, open the upper sliding drawer and enter into the menu to set the correct value for the
coins (tokens) to be paid-out (see Chapter 7. 3.6) .
As soon as the control board enables the note acceptor, the acceptor front slot flashes once in blue
colour for each enabled note, or once in red for each disabled note. For instance, if the 5, 10, 20
Euro notes are enabled, and the 50 and 100 Euro notes are disabled, the front slot will flash 3 times
in blue colour and 2 (twice) in red. The machine is now ready to operate.
All measures
in mm
A,
B, C, D, E, F =
Holes preset
for fastening
GIVES COINS
1,00 €
CHANGEONE
Promo
GIVES COINS
0,50 € 1,00 €
Hammer 1 One / CD Hammer 1 CD+CD
!
CHANGEONE
Set-up ongoing
620 0
650 0
A
B
C
D
E F

7
5.2 Control board connections
Pin 1. +24V
Pin 2. +12V [POWER SUPPLY]
Pin 3. GND
Pin 1. DATA
Pin 2. GND [AL66COIN ACCEPTOR]
Pin 3. NC
Pin 4. +12 V
[HOPPERONE S11 / HOPPERCD, HOPPERCD DISCRIMINATOR / HOPPER AH4]
Pin 1. DATA
Pin 4,8. GND
Pin 7,10. 24V
Pin 2,3,5,6,9. NC
Pin 1. CCT
Pin 2. GND
Pin 3. +12V [NOTE VALIDATOR]
Pin 4. +24 V
Pin 1. MICRO 1 (N.O.) 1 = Confirm OK
Pin 2. LED 1 MICRO 2
Pin 3. MICRO 2 (N.O.) 2 = Select SEL
Pin 4. LED 2 MICRO 2
Pin 5. NC [ILLUMINATED P.BUTTONS]
Pin 6. LED 1 MICRO 1
Pin 7. MICRO 3 = RESET RESIDUAL CREDIT / REFILL 3 = Reset Credit
Pin 8. LED 2 MICRO 1
Pin 9. GND
Pin10. +12V
Pin 1. MICRO or KEY > REFILL/RESET CREDIT
Pin 2. HOPPER LEVEL SENSOR [REFILL/ HOPPER LEVEL SENSOR]
Pin 3, 4, 6. NC
Pin 5. GND
Pin 1. MICRO N.O.
Pin 2. LED R (red)
Pin 3. +12V [RGB ILLUMINATED PB: RGB1 = Confirm; RGB2 = Select]
Pin 4. LED B (blue)
Pin 5. GND
Pin 6. LED G (verde)
P
P
P
R
R
R
O
O
O
G
G
G
+
+
+
-
-
-
O
O
O
K
K
K
P
P
P
W
W
W
R
R
R
I
I
IN
N
N
P
P
P
W
W
W
R
R
R
O
O
O
U
U
U
T
T
T
C
C
C
C
C
C
T
T
T
2
2
2
4
4
4
T
T
T
S
S
S
T
T
T
P
P
P
T
T
T
S
S
S
T
T
T
P
P
P
R
R
R
G
G
G
B
B
B
3
3
3
R
R
R
G
G
G
B
B
B
2
2
2
P
P
P
4
4
4
/
/
/
7
7
7
S
S
S
P
P
P
1
1
1
R
R
R
G
G
G
B
B
B
1
1
1
C
C
C
C
C
C
1
1
1
2
2
2
R
R
R
E
E
E
G
G
G
2
2
2
4
4
4
1
1
1
2
2
2
G
G
G
N
N
N
D
D
D
CMS
control board
Rear view
(shell side)
CCT 24
PW
R IN
CCT12
PWR OUT
P 4/7
24 12 GND
RGB 1,2,3
PT

8
6. Operation
HAMMER1 ONE e HAMMER1 CD:
slip the note, to be exchanged in coins or tokens, into the relevant acceptor slot: the machine will
automatically pay-out the corresponding coins or tokens.
NOTICE: the unit will not allow token accumulation, therefore token bonus will not be available unless the exact
required amount has been introduced altogether in one shot.
IMPORTANT: if token value accumulation is requested, it is possible to fit the machine with the standard pc board
CMS 1.0x: in this case, it will be necessary to add one pushbutton, whose activation will start the pay-out when the
desidered amount of money has been introduced.
HAMMER1 CD+CD:
slip into the acceptor slot the note to be exchanged in coins or tokens, the inserted amount shall be
displayed.
If the Automatic dispensing mode has been preset, the machine will pay the coins/tokens out
automatically, choosing as evenly as possible between the two denominations available in the
hoppers, compatible to the set values.
If the Manual dispensing mode has been preset, the display will propose to choose between the
two denominations available. The User will choose the one that she/he prefers by the Selection (+/-)
button, then she/he will Confirm (OK button) to get the pay-out change.
WARNING: If there are not enough coins in the hopper to fulfil the whole exchange request, the
remaining credit shall be displayed and retained in memory. Switch off the machine, fill the
hoppers, and switch on again: the remaining credit shall be paid out .

9
7. System configuration
7.1 Default menu
The HAMMER 1 is preset by default as follows (unless requested for different setup):
Board Parameters Pay-out mode = AUTOMATIC
Bonus = DISABLED
Level sensors = DISABLED
HopperOne or CD [ccTalk] Parameters Hopper number = 1
Coin value = € 1.00
Hopper number = 2
Coins value = € 0.50
BILLYONE or ORYONE Validator [ccTalk] Parameters € 5.00 - …. - € 100.00 = ENABLED
If any variation is made, it will be possible to restore the default configuration as follows:
enter the initial menu, scroll by UP and DOWN keys and choose
RESTORE DEFAULT CONFIGURATION
then press OK; the message DEFAULT CONFIG . RESTORED will be displayed.
NOTICE: the RESTORE DEFAULT CONFIGURATION command resets the default PIN code (0000)
7. 2 Configurating the Menu
7.2.1 Surf the Menu:
To enter the menu and navigate it, make use of the 3 keys located behind the board display side.
OK button enter the set-up menu or chosen menu; confirm chosen data
+ / – buttons surf the menu; modify figures or characters
To exit the menu, click DOWN until EXIT voice shows, then confirm exit by the OK key.
RESET OF RESIDUAL CREDIT: If there are not enough coins in the hopper to fulfil the whole
exchange request, the remaining credit shall be displayed and retained in memory. Switch off the
machine, fill the hoppers, and switch on again: the remaining credit shall be paid out .
As an alternative, it is possible to cancel the message of remaining credit by an additional
pushbutton or switch key-lock (not provided), and pay manually the credit left. Just connect the
pushbutton or switch key-lock between pins 7 and 9 (common GND) of socket J5.
The cancelled remaining credit will be recorded in the Show Accounts menu (see section 7.2.4).
Notice: access to some sub-menus is protected by the PIN.

10
7.2.2 Main structure of the Menu:
RESTORE DEFAULT
CONFIGURATION
MODIFY PIN
(only available if preset for:
DISPENSING MODE = TOKENS )
EXIT
MENU
PROMO
CHANGEONE
Promo
EXIT
MENU
SHOW
PERIPHERAL UNITS
SHOW
ACCOUNTS
RESET
ACCOUNTS
PERIPHERAL
UNITS SET UP
EMPTY OUT
HOPPER
LANGUAGE
SETUP
BONUS

11
7.2.3 Show peripheral units
This menu allows to check the state of the PERIPHERAL UNITS , for instance:
ecc. ecc.
7.2.4 Show accounts
Questo menu permette di leggere i totali e i parziali dell’incassato, dell’erogato, dei crediti agati
-Press OK: the display will show the total amounts introduced (T OTAL I N ). Press UP, and OK if
you want to exit the A
CCOUNTS menu.
-Or else, press DOWN to check the total amounts dispensed (T OTAL O UT ).
Press DOWN to go on browsing the submenu.
Notice: whenever the Partial Amounts record get cancelled (see section 7.2.3 RESET ACCOUNTS), the previous value
recorded in “Last Partials cancelled” gets replaced by the amount that has just been reset.
LAST AMOUNT DISPENSED: when the board is in stand-by condition, it is possible to check the last amount
diospensed, by holding the SELECT pushbutton for full 4”.
7.2.5 Reset accounts
To use this sub-menu it is necessary to digit the PIN code. This function allows to cancel the
account records (both paid out and cashed in) of the machine.
Exit
Total in
00,00 €
Coins out
00,00 €
Remained Credit
Paid 00,00 €
SHOW
ACCOUNTS
C OIN ACCEPTOR
DISCONNECTED
NOTE VALIDATOR
CONNECTED
RESET
ACCOUNTS
Total out
00,00 €
Banknotes in
00,00 €
Exit
RESET
ACCOUNTS
Reset
Total Amounts
Reset
Partial Amounts
Enter PIN
0
For each of the 4 digits of
thePIN, use UP and DOWN to
highlight the figure wanted, then
confirm by OK. At the end, the
display will show:
All Totals
cancelled
All Partials
cancelled
Exit
(*)
Banknotes out
00,00 €
Coins in
00,00 €
Once entered the PIN,
the display will show:
(*) Reset of the remaining credit: when the contact circuit has been preset (
see
section 3.3), it is possible to switch it and cancel the unpaid amount.
The Operator
will then pay it manually to the Customer, while the cancelled amount will be
recorded in the Accounts section (see 7.3.5 RESET ACCOUNTS).
Last partials
cancelled
IN: 00,00 €
OUT: 00,00 €
(*) Whenever the Partial Amounts record get cancelled (see
section 5.4), the previous value recorded in “Last Partials
cancelled” gets replaced by the amount that has just been reset.
(*)
HOPPER 1
EMPTY

12
7.2.6 Peripheral units set up
It is possible to configurate by this menu the cctalk coin acceptor, the ccTalk note validator, the
ccTalk hoppers, the pay-out mode and the keys mode.
-Note Validator setup
All the programmed note values (5-to-100 Euro) get automatically enabled. To modify this default
condition, press OK to get to the first option (ex. 5 €) and highlight it, then press UP or DOWN to
reverse its state. Press OK to shift to the next option (ex. 10 €).
Set up
Note validator
< 5 > 10 20 50 100
OK OK OK OK OK
< 5 > 10 20 50 100
NO OK OK OK OK
5 < 10 > 20 50 100
OK OK OK OK OK
5 10 < 20 > 50 100
OK OK OK OK OK
Set up
Note validator
Set up
Coin acceptor
P ERIPHERAL UNITS
SETUP
Exit
EMPTY OUT
HOPPERS
< 5 > 10 20 50 100
OK OK OK OK OK
5 < 10 > 20 50 100
OK OK OK OK OK
5 10 < 20 > 50 100
OK OK OK OK OK
< 5 > 10
20 50 100
NO OK OK OK OK
< 2,00 > 1,00 0,50
OK OK OK
< 2,00 > 1,00 0,50
NO OK OK
2,00 < 1,00 > 0,50
OK OK OK
2,00 1,00 < 0,50 >
OK NO OK
Set up
Dispense mode
Level sensors
enabled
Level sensors
disabled
Set up
COINS
Set up
TOKEN
Set up Hopper 1 :
1,00 €
(*) Press Down or
Up to modify amounts
in discreet steps of
0,05
€ each
Set up Hopper 2 :
0,50 €
Set up
TOKEN + CHANGE
Dispensing mode
AUTOMATIC
(*)
(*)
Dispensing mode
MANUAL
(**) In HopperCD use Tokens only if coin-like!
No grooves, no angles, no holes.
(***) available only in
HAMMER1 CD+CD
(**)
(**)
(***)
(***)
5 < 10 > 20 50 100
NO OK OK OK OK
2,00 < 1,00 > 0,50
NO OK OK

13
-Coin selector setup (not available in this machine)
Among the accepted coins (0.05-to-2 €), the following ones get enabled by default: 0.50 € - 1.00 € -
2.00 €. To modify this condition, press OK to get to the first option (ex. 2 €) and highlight it, then
press UP or DOWN to reverse its state. Press OK to shift to the next option (ex. 1 €).
-Dispensing Mode setup
Allows to choose whether to dispense C OINS or T OKENS or T OKENS +C HANGE , and whether the
DISPENSING MODE will be AUTOMATIC or MANUAL .
It also permits to monitor the level of the coins in the hopper(s) by the electronic sensors.
NOTA: monitoring of level sensors is disabled by default. This means that the board does not know when the hopper is
empty, so it will send the pay-out command even if there are no coins available.
If instead the monitoring has been enabled, and there are not enough coins in the hopper, the display will warn that the
hopper is empty. There are yet contained 20 coins approximately, to be able to complete the change payout.
7.2.7 E MPTY OUT H OPPER ( S )
Use this function to make the selected hopper pay out all the contained coins / tokens.
When depletion hase been completed, the paid out value will be displayed.
Set up
Coin acceptor
< 2,00 > 1,00 0,50
OK OK OK
< 2,00 > 1,00 0,50
NO OK OK
2,00 < 1,00 > 0,50
OK OK OK
2,00 1,00 < 0,50 >
OK NO OK
SET UP
DISPENSING MODE
Set up
COINS
Level sensors
enabled
Level sensors
disabled
Set up
TOKENS
Set up Hopper 1:
1,00 €
(*) Use keys
Down and Up to
modify values
(*)
Set up Hopper 2:
0,50 €
(*)
Set up
TOKENS+CHANGE
Dispense mode
AUTOMATIC
Dispense mode
MANUAL
(**) NOTICE:
1.
In HopperCD use Tokens
only if coin-like! No grooves,
no angles, no holes.
2. Option TOKEN+CHANGE
only if two
Hoppers are in
circuit.
(**)
(**)
EMPTY OUT
HOPPER
Deplete Hopper 1 Deplete Hopper 1
Total nn,nn €
Deplete Hopper 2
Deplete Hopper 2
Totale nn,nn €
Exit

14
7.2.8 R ESTORE DEFAULT CONFIGURATION
To use this sub-menu it is necessary to digit the PIN code.
If a wrong number is inserted, the following message will appear:
WARNING: in case of reset, the system sets back to default configuration. The PIN code will be
reset to the default 0000 setting. Account records shall not be cancelled.
7.2.9 P
ROMO
It is possible to preset an advertisment on the display. Press OK:
Press again OK, the pointer will highlight the first digit: by UP or DOWN, choose the character that
you want to insert, then confirm by OK. The pointer will highlight the following digit.
Once digit nr. 16 has been confirmed, the message gets stored.
7.2.10 B
ONUS S ET U P
This function will operate only if at least the hopper nr. 1 is preset for paying tokens. It allows to
bestow a programmable quantity of tokens, when a programmable amount of money has been
introduced. Take care to set up all hoppers parameters. Bonus function is disabled by default.
NOTICE: the unit will not allow token accumulation, therefore token bonus will not be available
unless the exact required amount has been introduced altogether in one shot.
If instead token value accumulation is requested, it is possible to fit the machine with the standard
pc board CMS 1.0x: in this case, it will be necessary to add one pushbutton (connect to RGB1
socket in the pc board): after the desidered amount of money has been introduced, activation of
such pushbutton will start the pay-out of the tokens.
RESTORE DEFAULT
CONFIGURATION
EnterPIN
0…
DEFAULT CONFIG .
RESTORED
The following message will briefly appear
after the PIN has been entered, then the
message
DEFAULT CONFIGURATION
RESTORED
will be shown again.
PIN error
Digit text
------------------------
BONUS
Bonus
ENABLE?
Bonus
DISABLE?
LEV EURO PCS
0 1€ 1
LEV EURO PCS
1 1€ 1
(*)Use Up key to modify
values
Bonus settings
stored
LEV EURO PCS
1 2..3..10 € 1
LEV EURO PCS
1 10€ 1
LEV EURO PCS
1 10€ 11
(*)
(*)
LEV EURO PCS
2 10€ 11
LEV EURO PCS
2 10€ 11
LEV EURO PCS
1 11..12.. € 1
NOTICE: in case of
mistakes, do confirm the
wrong programmed data,
then re-program correctly.

15
7.2.11 L ANGUAGE SETUP
7.2.12 M ODIFY PIN
The PIN code allows to get access to the discretional menus of the system.
The PIN code is made up by 4 figures (each of them from 0 to 9), so that there are 10,000
combinations available.
If the PIN code is not correct, the User is given another 4 tries before the board gets blocked-up by
its security interlock. The system can be started again by switching it off and on again.
ATTENTION: the default PIN code is 0000
The settings in the following menus can be modified by using the PIN code:
MODIFY PIN - RESET ACCOUNTS - RESTORE DEFAULT CONFIGURATION
To modify the existing PIN, press OK, and digit the old PIN code: to digit each code figure, first
use keys UP and DOWN to set each figure, then confirm it by OK. Once the 4
th
figure has been
confirmed, confirm by OK the whole old PIN:
To digit the new PIN code, use first the UP and DOWN keys to set each figure, then confirm it by
OK. Once the 4
th
figure has been confirmed, confirm by OK the whole new PIN.
As every single figure gets confirmed, an asterisk takes its place, so preserving secrecy.
NOTICE: when DEFAULT CONFIGURATION is restored, the PIN code gets reset to 0000.
7.2.13 E XIT M ENU
Press OK to go back to stand-by condition:
LANGUAGE
SETUP
Seleziona lingua
ITALIANO
Choose your language
ENGLISH
Waehlen Ihre Sprache
DEUTSCH
New PIN
0
Enter PIN
0
MODIFY PIN
EXIT MENU
Exit Menu
in progress…
CHANGEONE
Promo

16
8. Messages
8.1 Messages on the display
The following warning:
is accompanied by the system check. For instance, the following sliding warnings:
stand for:
the coin acceptor is not connected,
there is a fault in the note validator,
hopper 1 is properly working
The following error messages can possibly appear:
the mentioned peripheral unit (coin acceptor, or note validator,
or Hopper, a.s.o.) is connected and functioning
the mentioned peripheral unit has been disconnected
the mentioned peripheral unit is connected but faulty
the Hopper is empty
the inserted note is not enabled
The message
8.2 Note acceptor messages
8.2.1 BillyOne Note Validator
During operation, the amount of consecutive red flashes produced by the entry slot indicates the
possible malfunctions (see chart below):
nr. of red
flashes
Message description
1 Validator has been opened
2 Jammed banknote
3 Attempted fraud detected
5 Adjust optic sensor
9 Low voltage
11 Check operation of the encoder + motor of the validator
14 ROM error
CHANGEONE
OUT OF SERVICE
...COIN ACC
EPTOR…
.. DISCONNECTED ...
NIERA …. …. LET
SENTE …
.… IN ER
R N° 1… …. HOPPE
TED …. … EMPT
ORE … …. HOPPE
ORE …. … PRESE
PTOR …. …. NOT
CTED … .… IN ER
TOR… …. HOPPE
ROR …. … CONN
( PERIPH . UNIT )
CONNECTED
( PERIPH . UNIT )
DISCONNECTED
( PERIPH . UNIT )
IN ERROR
H OPPER
EMPTY
BANKNOTE
DISABLED
Remaining Credit
1 €
means that coins have run out during the payout.
Switch power off, fill it up, and switch power on again:
the board will prompt the hopper to complete the payout.

17
8.2.2 OryOne Note Validator
During operation, the amount of consecutive red flashes produced by the entry slot indicates the
possible malfunctions (see chart below):
nr. of red
flashes
Message description
1 Validator has been opened
2 Jammed banknote
3 Attempted fraud detected
5 Adjust optic sensor
7 Stacker is full: remove banknotes or replace it by an empty one
9 Low voltage
11 Check operation of the encoder + motor of the validator
12 Check operation of the encoder + motor of the stacker
14 ROM error
8.2.3 Fraud-fishing
9. Maintenance of the note validator
9.1 BillyOne Validator
BEWARE! Switch off before opening the note acceptor.
9.1.1 Cleaning the note validator:
The acceptance capacity may decrease due to dust accumulation (dust is mostly produced by the
passage of the banknotes), or residual sprays, which can accumulate on the sensors and rollers.
It is therefore recommended that you clean these parts at least monthly, as indicated below.
Please clean such parts at least once a month, as explained here below.
1. Turn the power off, and pull off the cable
connected to the 10-pin socket interface.
Press the yellow button C (see page 6), located
under the reader, to release the main body from the
Bezel; then slide it backwards and remove it.
Dip-Switch SW2 ON
A
fter fraud attempts
, the validator returns the banknote. No signal given.
(**) Dip-Switch SW2 OFF
Attempt
Validator reaction
Do as described below
1°
Remains in service
-
2°
Remains in service
-
3°
>
error (3 red flashes)
Reset (switch off then on)
… n° …
> error (3 red flashes)
Reset (switch off then on)
In validators with SW v. 1: after 5th attempt (3 yellow flashes) it is necessary to wait for
automatic restore of service. Take care not to switch the device off.
!
C

18
2. Move up the slide button D (left side of the BillyOne – see page. 6) and, while holding it up,
pull the cover lid backwards; then lift the cover up and rotate it 180° around the flat cable.
3. Gently wipe the sensors with a clean, lint-free cloth, or a cotton swab or with a small
sponge, possibly moistened with isopropyl alcohol.
4. Remove all dust and debris from the 4 silicon rollers, as well as from the relevant 4
matching wheels located beneath the cover lid. To remove the toughest calculus that may be
gripping on rollers and wheels, make use of isopropyl alcohol.
IMPORTANT: do not use organic
solvents (eg methylated spirits, paint
thinner or petrol). Use only isopropyl
alcohol.
1. Sensors
2. Silicon rollers
3. Matching wheels
5. Re-assemble the validator head by rotating 180° back the cover lid, lean it onto the base
until the base hooks get into their holes, then slide it frontward until hearing the closing
“click”.
9.1.2 Clearing jammed banknotes:
Please proceed as explained in points 1 and 2 above, to get access to the jammed banknotes. Once
removed the jamming has been removed, follow sdtep 5 to re-assemble.
9.2 OryOne Validator
PLEASE PAY ATTENTION! Switch power off before opening the validator.
9.2.1 Cleaning the note validator:
Please follow the steps as explained in section 9.1.
9.2.2 Clearing jammed banknotes:
Please follow the steps as explained in section 9.1.
9.2.3 Clearing jammed banknotes from the cash box:
!
D
A
A
A
A
A
B
C

19
1. Do not power up the validator during this
operation.
2. Remove the cash box.
3. Rotate the banknote transportation
gear leftwards or rightwards, until the banknote is
removed.
11. Disposal of the product
WARNING! DISPOSE OF THE PRODUCT ACCORDING TO THE
GOVERNING LAW IN YOUR COUNTRY!
This equipment may not be treated as household waste. Instead, it must be
handed over to the applicable collection point for the recycling of electric
and electronic equipment. By ensuring that this product is dised of
correctly, you will help to prevent potential negative consequences for the
environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
For more detailed information about recycling of this product, please
contact the Dealer where you purchased this product.
12. Terms of Guarantee
The manufacturer will fix malfunctions arising from production faults in this machine or parts of it
within 12 months from the date of sale.
All communications referring to guarantee repairs or replacements must be accompanied by the
product serial number and the copy of the sale invoice.
To obtain your guarantee repair, please send the part to the Dealer where you purchased the
machine, together with the following documents:
- copy of the sale invoice
- delivery note stating “returned for guarantee repair”
- detailed report of the problem found and the circumstances in which it occurs.
Before sending the product, please get in touch with your Dealer or with Alberici S.p.a. (+39 051
944300); very malfunctions can be fixed via a simple phone call, saving you costs and time.
Alberici S.p.a. will verify that warranty is applicable, i.e. that problem is not caused by:
- transport damages
- damages from incorrect installation or wrong configuration
- installation in premises or areas not complying with the prescribed safety requirements
- intentional or unwilled tampering
- wrong or careless use or maintenance
- non-compliance with precautions prescribed (see Chapter 4. Caution)
- natural disasters, vandalisms, intentional or unintentional damage
Guarantee is considered automatically expired if outer and inner labels are missing.
Transport costs of repaired products are at the Customer’s charge.
Transportation Gear

20
13. Customer Service
Alberici S.p.a. will be pleased to offer all the necessary information on use, ordinary maintenance
and technical service. Please call ([phone] and specify if your request concerns
information on use or technical support.