American DJ Master Blaster User manual

SPECIFICATIONS:
MODEL - Master Blaster-700™
ELECTRONIC THERMO SENSING
WEIGHT: 13 LBS.
DIMENSIONS: 6.5" X 6.5" X 16"
FUSE: 7A AGC
SUPPLY VOLTAGE: 120V
WARM UP TIME: 5 Minutes
TANK CAPACITY: 1 Quart Removable
OUTPUT: 4,000 cubic feet per minute
FLUID TYPE: Water Base American DJ Fog Juice™
DUTY CYCLE: Not to exceed 6 hours turned on.
HEATER: 700 WATT
Affordable Quality Lighting Products from American DJ Supply, Inc. Los Angeles, CA. 90058 Page 1
NNEEVVEERRPPOOIINNTTOORRAAIIMMAANNYYFFOOGGMMAACCHHIINNEE
TTOOWWAARRDDSSPPEEOOPPLLEEOORRTTHHEEIIRRCCLLOOTTHHIINNGG..
FFOOGGMMAACCHHIINNEESSEEMMIITTHHOOTTVVAAPPOORRAANNDD
SSHHOOUULLDDBBEEUUSSEEDDWWIITTHHTTHHEESSAAMMEECCAARREE
TTHHAATTYYOOUUWWOOUULLDDOOBBSSEERRVVEEWWHHEENNUUSSIINNGG
AANNEELLEECCTTRRIICCKKEETTTTLLEEOORRIIRROONN..
IINNTTRROODDUUCCTTIIOONN::
Congratulations, you have just purchased one of the most innovative and reliable fog
machines on the market today! The MMaasstteerrBBllaasstteerr--770000and the MMaasstteerrBBllaasstteerr11000000are
American DJ®User Instructions
TO HELP PREVENT UNIT FROM CLOGGING, USE
AMERICAN DJ® CLEAN MACHINE™ LIQUID. CLEAN
MACHINE IS RECOMMENDED WHEN STORING YOUR
FOGGER FOR MORE THAN 1 WEEK, OR AT LEAST ONCE
A MONTH AS NORMAL MAINTENANCE WHEN UNIT IS
BEING USED ALL THE TIME. ITS LIKE A TUNE UP FOR
YOUR FOG MACHINE! CLEAN MACHINE REMOVES PAR-
TICLE BUILD UP IN THE HEATER AND GIVES LONGER
LIFE TO THE FOG MACHINE. CLEAN MACHINE IS AVAIL-
ABLE IN GALLON OR QUART BOTTLES FROM YOUR
LOCAL AMERICAN DJ® DEALER.
SPECIFICATIONS:
MODEL - Master Blaster-1000™
ELECTRONIC THERMO SENSING
WEIGHT: 18 LBS.
DIMENSIONS: 6.25" X 7.5" X 19"
FUSE: 10A AGC
SUPPLY VOLTAGE: 120V
WARM UP TIME: 5 Minutes
TANK CAPACITY: 1 Quart Removable
OUTPUT: 12,000 cubic feet per minute
FLUID TYPE: Water Base American DJ Fog Juice™
DUTY CYCLE: Not to exceed 6 hours turned on.
HEATER: 1000 WATT
CAUTION! Read instructions before attempting to install or operate.
MASTER BLASTER™

part of American DJ’s new
ccoommmmeerrcciiaallsseerriieess
fog machines with patented Electronic
Thermo Sensing (E.T.S.), for continuous heating regulation.
FFuunnccttiioonnss::
The new Commercial Series MASTER BLASTER™ fog machines all come with E.T.S., for
continuous heating-regulation. These foggers also carry a new innovation in fog machine
technology, user cleanable heaters. The MASTER BLASTER ™ operates via a 25 ft. wired,
timer remote control, that comes mounted into the unit. The remote may be removed, by
unscrewing the four (4) thumb screws that hold it to the base. The unit also contains a
removable, one quart reservoir.
EElleeccttrroonniiccTThheerrmmooSSeennssiinngg//EE..TT..SS..::
This feature allows you to have fog output available at almost any time. A small on board
micro processor constantly monitors the operating temperature of the fog machine. When
the fog machine drops ONE (1) degree in temperature the E.T.S., automatically senses this
change and turns the heater on to raise the temperature that one degree lost. This enables
the end user to have fog output at anytime. The only time fog will not be available, is at the
end of the machines duty cycle (The fog output was maxed out and the heater has to
reheat completely).
OOppeerraattiinnggaannddRReemmootteeIInnssttrruuccttiioonnss::
Plug your fog machine into a standard 110V/120V supply. The remote control comes con-
nected to the fog machine but can be removed to access the 25ft. cord. Make sure there is
an adequate supply of American Fog Juice™ in the fluid reservoir. Running the fog machine
dry will cause pump failure and or clogging. This is the largest cause of failure in fog
machines. Only American Fog Juice™ is recommended and not all fog juice is created
equal. Once the machine is plugged in and turned on, a red L.E.D. will indicate the unit is
receiving power. The unit has a warm up time of five (5) minutes. After the unit has warmed
up, a GREEN L.E.D on the remote will light indicating the unit is ready to emit fog. To emit
fog, simply press the green button on the remote for desired length of time. If the GREEN
L.E.D. is on and fog does not come out after holding the button down for 30 seconds, check
the fluid tank and hose to make sure there is fluid going through the hose. You can also
operate the fog output automatically by adjusting the timer settings on the remote.
The remote has three (3) L.E.D.s that indicate different functions; The YELLOW L.E.D. will indi-
cated the timer is turned on and is activated. The RED L.E.D. indicates power is on. The
GREEN L.E.D. indicates fog output is available. The remote also contains two rotary knobs.
The Duration knob serves two functions 1) Turns the timer on and off. 2) Sets the timers dura-
tion (Length of fog output). The interval knob sets the amount of time in between fog out-
put from 30 seconds to 10 minutes.
CCaauuttiioonn::BBeeffoorreerreemmoovviinnggoorrrreeppllaacciinnggtthheerreemmootteeuunniittddiissccoonnnneecctttthheeppoowweerrssuuppppllyy..
Affordable Quality Lighting Products from American DJ Supply, Inc. Los Angeles, CA. 90058 Page 2

Heater Service:
The MASTER BLASTER™ foggers all come with a unique and innovative removable heater
unit. This exciting feature allows the end user to remove and clean the heater core when it
becomes clogged or dirty.
SSeerrvviiccee::
1.
AAllwwaayyssrreemmeemmbbeerrttooddiissccoonnnneecctttthheeppoowweerrssuuppppllyywwhheennsseerrvviicciinnggtthhiissoorraannyyuunniitt
.
2. Remove the heater core with a wrench.
3. With a wire brush, carefully clean off all corrosion and grime build up.
4. You may also soak the heater core in a bath of American Clean Machine. This will help
loosen the corrosion build up making it easier to scrub off with a wire brush.
5. Remove and replace the heater core gasket -
FFaaiilluurreettoorreeppllaacceetthheeoollddggaasskkeettwwiillllrreessuulltt
iinnffooggjjuuiicceelleeaakkiinnggffrroommtthheeffrroonnttoofftthheennoozzzzllee..
6. After you have removed all the corrosion build up and have replaced the gasket,
replace the heater core and tighten.
BBeessuurreennoottttoooovveerrttiigghhtteenntthheehheeaatteerrccoorree
7. Reconnect power supply.
TTrroouubblleeSShhoooottiinnggaannddSSeerrvviiccee::
If you experience low output, pump noise, or no output at all, disconnect immediately. Do
not attempt to continue pushing the remote button as this may damage unit. Check fluid
level, the external fuse, remote connection, and check power from wall. If all of the above
appear to be O.K., and the unit fails to operate correctly, the unit will require service. Return
the machine to an American DJ Authorized dealer or service center.
All commercial series, MASTER BLASTER™ foggers carry a one year limited warranty.
We recommend you fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be freight pre-paid and
accompany a R.A. #. If the unit is under warranty, you must provide a proof of purchase
invoice.
Affordable Quality Lighting Products from American DJ Supply, Inc. Los Angeles, CA. 90058 Page 3
AMASTER BLASTER™
700 fogger shown with its
heater core removed.