American Dynamics LIRC0308CS User manual

M M JUT 1
AMERICAN
DYNAMICS
CCTV LENS
OWNER’S MANUAL
LIRC0308CS, L1RC1040CS, LIRC2811CS
Thank you for purchasing our Aspherical CCTV Lenses. These new auto iris lenses are used to produce consistent video signals from cameras that view
scenes with varying light levels. The use of auto iris lenses enables reliable monitoring in areas, which would otherwise be compromised. In order to
understand the lens specification and performance, please read this manual.
IR L«ns
These lenses are designed to have the same focal point in the IR light range as in the visible light range. Since there is no focus shift in any
lighting condition, the lens is ideal for use with Day/Night cameras. However, as the depth of field in the IR range is very narrow, focus
adjustment should be done very carefully. So, when you install the lens with IR illumination, please check your focus setting in both visible
light and IR light.
MOUNT-TYPE
Your new AMERICAN DYNAMICS Lens is equipped with a CS mount. Before you use the lens, please make sure that the mount type
matches that of your camera.
INSTALLATION ON CAMERA
The lens is installed by screwing it clockwise into the mount on the CCTV camera. Once the lens is screwed in completely to its mechanical
stop position, you will then be able to rotate lens chassis back to suit the set-up position of the camera.
WIRING DIAGRAM
Please read the User’s Manual for the devices such as the camera and controller before wiring. Then please follow the chart below to
insure the right connection.
Cable
Supplied with 4Pin Square Connector (JEITA)
Yellow
Control (+)
1
Control (+)
Orange
Control (-) 2
Control (-)
Red
Drive (+)
3 Drive (+)
Black
Drive (-)
4 Drive (-)
IRIS
LIRC0308CS, LIRC1040CS, LIRC2811CS
If the camera has a selection switch between Video and DC, please set it DC.
TO INSURE LONG TERM USE
❖ Please remove dust on the lens by using a blower or soft brush. Avoid touching the lens surface.
❖ In order to remove fingerprints or oil stains on the lens surface, use lens cleaning paper or clean cotton cloth with a little cleaning liquid.
Then, wipe off the stains lightly starting from the center of the lens surface. Please wipe the lens body with a silicon cloth. Avoid using
any organic solvents such as thinner or benzene.
Thank you for using American Dynamics products. We support our products through an extensive worldwide network of dealers. The dealer
through whom you originally purchased this product is your point of contact if you need service or support. Our dealers are empowered to
provide the very best in customer service and support.
Dealers should contact American Dynamics at [phone] or [phone] or on the Web at www.americandvnamics.net
8200-0843-01 AO

m
SPECIFICATION *Specifications are subject to change without notice.
IR lens
Model LIRC0308CS LIRC2811CS
LIRC1040CS
Imager Size 1/3"
Focal Length 3-8mm 2.8-11mm
10-40mm
Aperture FI.0-360
FI.4-360
FI.4-360
Angle of view
(Horizontal x Vertical)
Wide
90.8° X 66.6° 97.4°x72.4°
27.6 °x20.4°
Tele 36.2 x27.0°
26.2°xl9.7° 7.0°x5.3°
Back Focus(in air)
Wide: 8.36mm Tele: 14.12mm
8.66-18.69mm
18.61mm-12.17mm
Mount Type cs
Dimensions(mm)
33x40.2
40x54.6
39x67
Operation Voltage(V) Open: 4.0V Close: 0.7V Open: 3.3V Close: 0.7V
Open: 3.0V Close: 0.5V
AMERICAN
DYNAMICS
AMERICAN DYNAMICS Safety Precautions
These precautionary statements are classified into two levels
A
Warning !
If the user does not obey these instructions
and misuses the product, serious injury or
loss of life may occur.
of danger depending on the content and grade of elements t hat comprise the product.
A
Caution !
If the user does not obey these instructions
and misuses the product, serious injury and/
or property damage may occur.
The follwing symbols are used in these precautionary statements.
A
Shock!
This symbol warns that an electrical
current is present and electric shock
may occur.
®
Do not 1
This symbol means that you should not
disassemble the product.
A.
Fire!
This is a fire hazard symbol that means
these is the possibility of igniting fire.
«
Direction !
This symbol means that you should pay
attention to certain handling procedures.
WARNING
Don't disassemble the unit or try to put any /V
foreign substance in it : especially metal of 'O'
flammable matter. Doing so could cause <A
electric shock and/ or fire. /H\
Don't scratch, open, twist or heat the A A
connector cable because doing so many
cause fire and / or electric shock. A\
Don’t attempt to use product it you suspect *
something isn’t right as in seeing smoke or ^
detecting a strange smell. If you use the A
product under these conditions lire and/ or /t\
If the connector cable is cracked or —. A
damaged, please exchange it by writing to (M ^
with an exchange request. If you .
continue to use the damaged cable, fire ^
and/ or electric shock may result. ^
Please keep the unit away form water, if /V
water should get inside the unit, stop using O' /P\
immediately, otherwise eiectric shock A
and/ or fire may occur. /*\
electric shock could occur.
Don't look through the lens directly at the
sun since this could cause blindness. PO
Don’t place the unit near extreme heat,
flame or gas since combustion may occur
resulting in fire. /n\
Don’t try to repair the unit or any power
source since that may cause fire and/ or
eiectric shock. A\
Keep the product out of the reach of
children. If the product fell on a child, injury
could occur.
CAUTION
Don’t place the product in locations with
extremely high or low temperatures. Don’t use
the product in areas that are hotter than 60
degress Centigrade or colder than - 10 degrees
Centigrade. Such extremes will effect the
quality performance of the product and could
damage it.
Don’t plug in or pull out the cable to or from an /C\
electrical outlet with wet hands. This may result vV
in electric shock.
Don't place the product near a stove or *
humidifier or any place where mere is high OO ^
heat or moisture. Fire and/ or electric A
shock may occur. ^
When attaching me lens to the camera body,
make sure you grip it securely to avoid the
possibility of the lens falling and becoming
damage.
If you going to connect the product with
aonther product, please read the connection
instructions from both product manuals
carefully before attempting any connection.
Otherwise damage may result to one or both
products.
Don’t point the lens directly at the sun or other
strong fight since that could damage the image
sensor on the camera and result in poor image
quality.
When storing the lens, keep it out of direct
sunlight. Fire could occur as a result of the light (\)
being reflected off the lens onto a flammable .
substance. /^\
Don't drop or hit the product forcefully. This
may cause product performance failure. VjJ
If you going to use a lens that has a tripod
mount but are using a camera body that is
heavier than the lens, please use the tripod
mount on the camera. Failure to do so could
result in severe damage to the lens.
Don't place the connector cable next to a A.
heater since it could melt and cause fire
and/ or electric shock. /%\
Don't place in dusty and humid place. Fire
and/ or electric shock may occur.
8200-0843-01 AO