American Standard Colony Oval 1742 Series User manual

INSTALLATION INSTRUCTIONS
753571-100 © American Standard Inc. 2004
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
COLONY OVAL™ WHIRLPOOL/BATHING POOL
1742 SERIES
FOR AFTER-SALES SERVICE CALL 1 [phone] WEEKDAYS.
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. AFTER INSTALLATION, AND
BEFORE ENCLOSING WITH WALLBOARD, TILE, ETC., WATER TEST THE UNIT AND CHECK FOR LEAKS.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFCI
Outlet
• Cement, Plaster,
Grout
1803 mm
(71)
ROUGH
FLOOR
1-1/2 O.D.
TAILPIECE
▲OUTLINE OF
CUTOUT-USE
TEMPLATE
292 mm
(11-1/2)
1041 mm
(41)
555mm
(21-7/8)
82mm
(3-1/4)
51mm
(2)
535mm
(21)
98mm
(3-7/8) C
LOF DRAIN
OUTLET
605mm
(23-7/8 )
1-1/2 N.P.T.M.
THREADS 35mm
(1-3/8)
305mm(12) X 229 mm(9)
CUTOUT IN FLOOR FOR DRAIN
98mm
(3-7/8)
PROVIDE ACCESS
TO PUMP FOR
SERVICING ON ALL
INSTALLATIONS
ON/OFF
SWITCH
PUMP MAY
EXTEND
TO THE RIM
SEE FTTG.SPECS
FOR DIMENSION
C
LOF SUPPLIES
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
1651-1981mm
(65-78)
OPTIONAL
102mm
(4)
305mm
(12)
(2) AIR VALVES
BATH
SUPPORT
MATERIAL
GENERAL SPECIFICATIONS FOR 1742 WHIRLPOOL
71 x 41 x 23-7/8 In.(1805 x 1040 x 606mm)
119 Lbs. (54 Kg.)
680 Lbs. (308 Kg.)
67 Gal. (254 L)
50 Gal. (190 L)
49 x 26 In. (1245 x 660mm)
62 x 34 In. (1588 x 864mm)
16-7/8 In. (429mm)
32 Lbs./Sq.Ft. (157 Kgs./Sq.m)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.1 HP, 9.9 AMPS, 120V.PUMP
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
IMPORTANT: Water test unit before installation
and enclosure!

SUGGESTED INSTALLATION
METHOD
LEVELING SURFACE
WATERPROOF
SEALANT
BATH
FRAMING AND INSTALLATION
THE VARIETY OF INSTALLATIONS POSSIBLE FOR THIS BATH MAY REQUIRE FRAMING PROCEDURES OTHER THAN THOSE SHOWN.
LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS, PROVISION MUST
BE MADE IN ALL INSTALLATIONS FOR AN ACCESS OPENING FOR SERVICING PUMP AND CONTROLS.
THE FOLLOWING PROCEDURE MUST BE USED FOR ALL INSTALLATIONS: STRINGER OR PIER HEIGHT SHOULD BE AS INDICATED.
THIS BATH MUST BE SUPPORTED ALONG ITS ENTIRE BOTTOM. We recommend the use of mortar as bedding material
(sand is not recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been
poured, and before it sets, position whirlpool or bath within recess until the rim is leveled against the leveling stringers (see
"Typical Recess Installation") shown below. The rim of the bath MUST NOT support weight. Allow the bedding material to
completely harden before applying weight to the rim or bottom of the bath. Any finish material such as tile or wall board must
be self-supporting if it contacts the deck of the bath.
753571-100 (2)
TYPICAL INSTALLATION
AS DESIRED *39
(991 mm)
CUTOUT
AS DESIRED
*69
(1753 mm)
CUTOUT
21-7/8
(556mm)
ACCESS PANEL
12
(305 mm)
*SEE CUTOUT TEMPLATE PROVIDED
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610 mm) IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.
24
(610mm)
IT MAY BE NECESSARY TO
NOTCH THE DECK SURFACE
TO ACCOMMODATE THE
WHIRLPOOL ON/OFF SWITCH
AND/OR THE AIR CONTROL
DURING INSTALLATION

ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
BLACK
WHITE
120 VAC
GND.
SEPARATE 15 AMP GFCI
FOR 1.1HP MODELS
WHIRLPOOL MOUNTED
AIR SWITCH
or
WALL TIMER
ELECTRICAL INSTALLATION
PUMP/MOTOR
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all
other applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired
from the electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply
panel. A grounded neutral wire and a third wire, earth ground, are essential.
753571-100 (3)

WIRE SELECTION GUIDE
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the pump
couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of the
highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings are
factory tightened and inspected, some loosening may have occurred during transit.) Make sure the whirlpool is connected
to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the whirlpool is
running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or
stains may be removed using granular Spic and Span®mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
FEATURES of YOUR NEW AMERICAN STANDARD ACRYLIC BATHTUB
Your new acrylic bathtub has been molded in the newest plumbing fixture material available today. Acrylics are
tough durable finishes that are simple and easy to care for.
The colors have been formulated to match other American-Standard fixtures and enhance your choice of
bathroom decorations. The high gloss surface is resistant to impact and chemicals and will retain its lasting
luster with proper care and maintenance.
AFTERCARE and CLEANING
•Always fill the tub with temperate water. Excessively hot water may cause surface damage
•Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.
•Clean after use with a mild liquid household detergent cleaner. Do not use Lestoil, Lysol Disinfectant (spray
or concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner,
or cleaning products in aerosol cans.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
•Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits, or other surface
blemishes.
•Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses
its sheen, dulled areas can be restored by rubbing with a white "automotive type" polishing compound and
waxing with a "liquid wax."
•Do not wax areas where you walk or stand.
•Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into
contact with the surface.
•Clean the surrounding surface immediately after using caustic drain cleaners.
•Burning cigarettes will damage the surface.
•Should damage to the fixture occur, repairs can be made quickly and easily.
Your distributor or builder can provide details.
Maximum distance from
fusebox to motor The sizes shown on this
chart are recommendations
for copper conductors
only. Always follow
local and national
electrical codes
Motor
Hi-Performance
Rating
50' 100'
120V Power Line
150' 200'
12 12 10 8
1.1
753571-100 (4) SPIC AND SPAN®IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE