American Standard Heritage 6' Whirlpool 2806.018WC User manual

H35
© 2007 American Standard Inc.
HERITAGE 6'™
WHIRLPOOL
HIGH GLOSS
Revised 6/07
HERITAGE 6'™ WHIRLPOOL
❏2806.018WC Whirlpool Featuring System I:
• Acrylic with berglass reinforcement
• EverClean™ whirlpool system featuring
Antimicrobial AlphaSan®
• Pre-leveled tub bottom
• Dual, molded-in arm rests
• Integral faucet deck area
• 2.0 HP, two speed, self-draining pump/motor
• Factory installed power cord and plug
• Eight multi-directional and ow-adjustable
jets including:
- Two Ideal-ow jets
- Four body massage jets
- Two recessed back-rest jets
• Deck-mounted air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater
connection system
• Factory installed and tested whirlpool system
❏2806.028WC Whirlpool Massage Featuring
System II
Same as 2806.018WC except:
• 2.0 HP, two speed self-draining pump/motor
with dry run seal and Pulse feature
• Deck-mounted electronic On/Off with 20 minute
built-in timed safety shut off and chrome bezel
Nominal Dimensions:
1829 x 908 x 546mm
(72" x 35-3/4" x 21-1/2")
Compliance Certications -
Meets or Exceeds the Following Specications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
AND PRODUCT SPECIFICATIONS
To Be Specied - Required:
❏Color:
❏Bath Filler: (specify nish)
❏Bath Drain: 1583.470 (specify nish)
To Be Specied - Optional:
❏Safe-T-Heater*: 9075.120
❏Grab Bar Kit: 9822-200-two per kit (specify color)
❏System II Control Bezel: 9861.100 (specify nish
For color/nish availability and other faucet choices, please
see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.

H36
© 2007 American Standard Inc.
HERITAGE 6'™
WHIRLPOOL
HIGH GLOSS
Revised 6/07
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP
OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
▲CUTOUT TEMPLATE PROVIDED IN SHIPPING BOX. MAY BE REQUESTED SEPARATELY. OPTIONAL GRAB BAR KIT AVAILABLE
AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
SUPPLY PIPING NOT INCLUDED.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
908mm
(35-3/4)
457mm
(18)
279mm
(11)
INTEGRAL
FITTING DECK
ON/OFF
SWITCH
1829mm
(72)
PUMP
140mm
(5-1/2) C/L OF
DRAIN
OVERFLOW
OUTLINE OF
CUTOUT
229 x 330mm
(9 X 13)
FLOOR
CUTOUT
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
LEVELING STRINGER
(NOT FOR SUPPORT)
1-1/2 N.P.T.M. THREADS
51mm
(2)
108mm
(4-1/4)
546mm
(21-1/2)
495mm
(19-1/2)
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
1-1/2 O.D.TAILPIECE 51mm
(2)
108mm
(4-1/4)
SAFE-T-HEATER
REMOVABLE
BLANK
C/L OF
OVERFLOW
GENERAL SPECIFICATIONS FOR 2806 WHIRLPOOL
72 x 35-3/4 x 21-1/2 In. (1829 x 908 x 546mm)
135 Lbs. (61 Kg.)
744 Lbs. (338 Kg.)
73 Gal. (276 L)
44 Gal. (167 L)
45 x 24 In. (1143 x 610mm)
60 x 30 In. (1524 x 762 mm)
15 In. (381mm)
41 Lbs./Sq.Ft. (198 Kgs./Sq.m)
25.6
49.4
2.1 HP, 14.4 AMPS ,120V.
2.1 HP, 15.6 AMPS ,120V.
SYSTEM I PUMP
SYSTEM II PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)