American Standard Colony Corner 1730 SERIES User manual

INSTALLATION INSTRUCTIONS
753451-100 Rev. A © American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
COLONY™ CORNER WHIRLPOOL/BATHING POOL
1730 SERIES
FOR AFTER-SALES SERVICE CALL 1 [phone] WEEKDAYS.
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately. After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
If a whirlpool, do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or
piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing
materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess
installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
List of Optional Components (not included):
• Apron Kit*
* see your American Standard Distributor
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFCI
Outlet
• Cement, Plaster,
Grout
495mm
(19-1/2) 117mm
(4-5/8)
C/L OF DRAIN
OUTLET
51mm
(2)
1546mm
(60-7/8)
ALT.
PUMP
1064mm
(41-7/8)
686mm
(27)
318mm
(12-1/2)
1168mm
)(46
1514mm
(59-5/8)
TOP OF
DECK
445mm
(17-1/2)70mm
(2-3/4)
ROUGH
FLOOR
83mm
(3-1/4)
BATH SUPPORT MATERIAL 38mm (1-1/2)
O.D.TAILPIECE
PUMP
PROVIDE ACCESS
FOR SERVICING
PUMP & CONTROLS
(6) JETS
ON/OFF
SWITCH
2 AIR
VALVES
LEVELING
STRINGER
NOT FOR
SUPPORT
483mm
(19)
2134mm
)(84
*
60 x 60 x 19-1/2 In.(1524 x 1524 x 495mm)
115 Lbs. (52 Kg.)
908 Lbs. (412 Kg.)
95 Gal. (360 L.)
65 Gal. (246 L.)
30 x 50 In. (762 x 1270mm)
45-1/2 x 63-1/2 In.(1156 x 1613mm)
13 In. (330 mm)
36 Lbs./Sq. Ft. (177 Kgs/Sq. m.)
27.8
54
GENERAL SPECIFICATIONS FOR 1730 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.1 HP, 9.9 AMPS, 120V.SYSTEM I PUMP
* NOTE: If the optional apron (PN 0730.121) is to be used with this
tub, the stringer height must be referenced from the finished floor.

TYPICAL CORNER INSTALLATION
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610 mm) IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.
59-1/2
(1511 mm)
CUTOUT
59-1/2
(1511 mm)
CUTOUT
30
(762 mm)
17-1/2
(445 mm)
12
(305 mm)
24
(610 mm)
LEFT-HAND DRAIN
ACCESS PANEL
RIGHT-HAND DRAIN
ACCESS PANEL
LEVELING
STRINGER
FRAMING AND INSTALLATION
THE VARIETY OF INSTALLATIONS POSSIBLE FOR THIS BATH MAY REQUIRE FRAMING PROCEDURES OTHER THAN THOSE
SHOWN.
LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS,
PROVISION MUST BE MADE IN ALL INSTALLATIONS FOR AN ACCESS OPENING FOR SERVICING PUMP AND
CONTROLS.
THE FOLLOWING PROCEDURE MUST BE USED FOR ALL INSTALLATIONS: STRINGER OR PIER HEIGHT SHOULD BE AS
INDICATED. THIS BATH MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM. WE RECOMMEND THE USE OF
MORTAR AS A BEDDING MATERIAL (SAND IS NOT RECOMMENDED). APPLY ENOUGH BEDDING TO SUPPORT THE
COMPLETE BOTTOM OF THE BATH. AFTER THE BEDDING HAS BEEN POURED, AND BEFORE IT SETS, POSITION
WHIRLPOOL OR BATH WITHIN INSTALLATION UNTIL THE RIM IS LEVELED AGAINST THE LEVELING STRINGERS (SEE
"TYPICAL CORNER INSTALLATION") SHOWN BELOW. THE RIM OF THE BATH MUST NOT SUPPORT WEIGHT. ALLOW
THE BEDDING MATERIAL TO COMPLETELY HARDEN BEFORE APPLYING WEIGHT TO THE RIM OR BOTTOM OF THE
BATH. ANY FINISH MATERIAL SUCH AS WALL BOARD OR TILE MUST BE SELF-SUPPORTING IF IT CONTACTS THE
DECK OF THE BATH.
753451-100 Rev. A (2)
SUGGESTED INSTALLATION
METHODS
LEVELING SURFACE
WATERPROOF
SEALANT
SUNKEN OR ISLAND
INSTALLATION RECESSED INSTALLATION
BATH
WATERPROOF
SEALANT
TILE
TILE
BEAD
STRIP
LEVELING
STRINGER
BATH
*
*NOTE: If the optional apron (PN 0730.121) is to be used with this tub, the stringer
height must be referenced from the finished floor.

ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
BLACK
WHITE
120 VAC
GND.
SEPARATE 15 AMP GFCI
OUTLET
WHIRLPOOL MOUNTED
AIR SWITCH OR
WALL TIMER
ELECTRICAL INSTALLATION
PUMP/MOTOR
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other
applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded
neutral wire and a third wire, earth ground, are essential.
753451-100 Rev. A (3)

WIRE SELECTION GUIDE
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the
whirlpool is running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or
stains may be removed using granular Spic and Span®mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing
with a white automotive-type polishing compound and waxing with a liquid wax.
Maximum distance from
fusebox to motor The sizes shown on this
chart are recommendations
for copper conductors
only. Always follow
local and national
electrical codes
Motor
Hi Performance
Rating
50' 100'
120V Power Line
150' 200'
12 12 10 8
753451-100 Rev. A (4) SPIC AND SPAN®IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
1.1