American Standard Doral Classic Champion 2076 User manual

SAVE FOR FUTURE USE
730529-100 Rev. M
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2006
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant
Hacksaw Wax Ring/Gasket Flexible Supply Tube 1/2" Deep Well Nut Driver or
Closet Bolts Tape Measure Carpenters Level Deep Well Socket Wrench
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
1
Recommended fitting type for back-to-back installations.
Depending upon your plumbing and venting conditions, the flow from
the Champion in a back-to-back installation may create a vacuum on
the system and draw water from the opposing bowl. The National
Standards Plumbing Code prohibits the use of a cross fitting for
drainage as throw over is possible. The code does approve a
directional "Y" style fitting with proper venting to direct the water
downward and away from the other toilet.
NOTE: BACK-TO-BACK INSTALLATION
Model 2002 Champion® Right Height™ Elongated Two Piece Toilet
Model 2018 Champion® Normal Height Elongated Two Piece Toilet
Model 2023 Champion® Normal Height Round Front Two Piece Toilet
Model 2057 Champion® Select Right Height™ Elongated Two Piece Toilet
Model 2087 Champion® Select Normal Height Elongated Two Piece Toilet
Model 2035 Champion® Select Normal Height Round Front Two Piece Toilet
Model 2058 Doral Classic™ Champion® Right Height™ Elongated Two Piece Toilet
Model 2074 Doral Classic™ Champion® Normal Height Elongated Two Piece Toilet
Model 2076 Doral Classic™ Champion® Normal Height Round Front Two Piece Toilet
Model 2367 Doral™ Champion® Right Height™ Elongated Two Piece Toilet
Model 2368 Doral™ Champion® Normal Height Elongated Two Piece Toilet
Model 2369 Doral™ Champion® Normal Height Round Front Two Piece Toilet
Model 2625 Oakmont™ Champion® Normal Height Elongated Two Piece Toilet
Model 2627 Oakmont™ Champion® Normal Height Round Front Two Piece Toilet
Model 2738 Oakmont™ Champion® Right Height™ Elongated Two Piece Toilet
Model 2733 Townsend™ Champion® Right Height™ Elongated Two Piece Toilet
Model 2735 Townsend™ Champion® Right Height™ Round Front Two Piece Toilet
Champion® 2-piece Toilets
Champion® Select 2-piece Toilets
Doral™ Champion® 2-piece Toilets
Doral Classic™ Champion® 2-piece Toilets
Oakmont™ Champion® 2-piece Toilets
Townsend™ Champion® 2-piece Toilets
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.
To ensure this product is installed properly, please read these instructions carefully before you begin.
(Certain installations may require professional help.) Also be sure your installation conforms to local codes.
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!

3
CLOSET FLANGE
CLOSET BOLTS
A
WAX RING
SEALANT
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax
ring evenly around waste flange, with tapered end of ring facing
toilet. Apply a thin bead of sealant around toilet base.
730529-100 Rev. M
- 2 -
2
FINISHED WALL
19mm ±6mm
(1 ±1/4)
419mm
(16-1/2)
FINISHED
FLOOR
305mm
(12)
772mm
(30-3/8)
83mm
(3-1/4)
A
470mm
(18-1/2)
C
B
16mm
(5/8)
E
D
SUPPLY
AS
REQ'D
F
152mm
(6)
254mm
(10)
356mm
(14)
FINISHED WALL
19mm ±6mm
(1 ±1/4)
387mm
(15-1/4)
FINISHED
FLOOR
305mm
(12)
772mm
(30-3/8)
721mm
(28-3/8)
83mm
(3-1/4)
A
470mm
(18-1/2)
419mm
(16-1/2)
C
B
16mm
(5/8)
E
D
SUPPLY
AS
REQ'D
F
152mm
(6)
254mm
(10)
356mm
(14)
*
*
*ROUND FRONT
MODELS
NOTE: DRAWINGS ARE FOR DIMENSIONAL PURPOSES ONLY. THEY ARE NOT EXACT REPRESENTATIONS.
MODEL AB CD EF
DIMENSIONS
2002 229mm (9) 264mm (10-3/8) 362mm (14-1/4) 483mm (19) 860mm (33-7/8) 254mm (10)
2018 229mm (9) 264mm (10-3/8) 362mm (14-1/4) 483mm (19) 829mm (32-5/8) 254mm (10)
2023 229mm (9) 264mm (10-3/8) 362mm (14-1/4) 483mm (19) 829mm (32-5/8) 254mm (10)
2057 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 489mm (19-1/4) 873mm (34-3/8) 254mm (10)
2087 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 489mm (19-1/4) 841mm (33-1/8) 254mm (10)
2035 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 489mm (19-1/4) 841mm (33-1/8) 254mm (10)
2058 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 479mm (18-7/8) 873mm (34-3/8) 254mm (10)
2074 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 479mm (18-7/8) 851mm (33-1/2) 254mm (10)
2076 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 479mm (18-7/8) 851mm (33-1/2) 254mm (10)
2367 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 492mm (19-3/8) 872mm (34-5/16) 254mm (10)
2368 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 492mm (19-3/8) 844mm (33-1/4) 254mm (10)
2369 216mm (8-1/2) 264mm (10-3/8) 362mm (14-1/4) 492mm (19-3/8) 844mm (33-1/4) 254mm (10)
2625 216mm (8-1/2) 273mm (10-3/4) 381mm (15) 492mm (19-3/8) 844mm (33-1/4) 286mm (11-1/4)
2627 216mm (8-1/2) 273mm (10-3/4) 381mm (15) 492mm (19-3/8) 844mm (33-1/4) 286mm (11-1/4)
2738 216mm (8-1/2) 275mm (10-13/16) 384mm (15-1/8) 492mm (19-3/8) 872mm (34-5/16) 295mm (11-5/8)
2733 216mm (8-1/2) 267mm (10-1/2) 379mm (14-7/8) 479mm (18-7/8) 873mm (34-3/8) 284mm (11-3/16)
2735 216mm (8-1/2) 267mm (10-1/2) 379mm (14-7/8) 479mm (18-7/8) 873mm (34-3/8) 284mm (11-3/16)
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide into
place 6" (152 mm) apart and parallel to wall.
ROUGHING-IN DIMENSIONS: 2002, 2057, 2058, 2367, 2738, 2733
Right Height™ Elongated Two Piece Toilet
ROUGHING-IN DIMENSIONS: Normal Height Elongated Two Piece Toilet
Normal Height Round Front Two Piece Toilet
Right Height™ Round Front Two Piece Toilet

730529-100 Rev. M
- 3 -
5
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet
on closet flange so bolts project through
mounting holes.
b. Loosely install retainer washers and nuts.
Side of washers marked "THIS SIDE UP"
must face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
6INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers.
(If necessary, cut bolt height to size before installing caps.)
c. Smooth off the bead of sealant around base.
Remove excess sealant.
!
CLOSET BOLT
NUT
WASHER
BOLT CAP
9a Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts
required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
Captive cone
washers already
included. No
additional washers
needed.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUTLOCK NUT LOCK NUT LOCK NUT
COUPLING
NUT
COUPLING
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
WATER
SHUT-OFF
CONE
WASHER
EXISTING
CONE
WASHER
EXISTING
WASHER
MANIFOLD INSIDE WATERWAY -
DO NOT REMOVE
INSTALL TANK
a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank
onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening,
and tank mounting bolts go through mounting holes. Secure with metal
washer/nuts.
b. With tank parallel to wall, alternately tighten hex nuts until tank is snugged down
evenly against bowl surface.
Recommended tool: Deep socket tool included in tank kit.
!CAUTION:
7
8INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
DO NOT SPIN BOLTS WITH SCREWDRIVER
RUBBER
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
WASHER/NUT
CLOSET FLANGE

730529-100 Rev. M
- 4 -
109b
ADJUSTMENTS
a. Adjust water level. Water level should be adjusted to level indicated in tank by adjusting float
cup. See Step 11 for water level adjustment method.
IMPORTANT:
b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead
chain from the retainment clip (see Fig. 10A) and take up slack on the chain, and reinsert on lift
rod. Make sure the chain is not too taught.
With correct washers in
place (see Step 9a), tighten
COUPLING NUT 1/4 turn
beyond hand tight.
DO NOT OVERTIGHTEN.
TANK
LEVER
REFILL
TUBE
LINK
TOP ARM
NIPPLE
Diagram 1
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
CONE WASHER
VALVE
BODY
WATER LEVEL
ADJUSTMENT
CLIP
THREADED
SHANK
SHANK
WASHER
COUPLING NUT
(HAND TIGHT ONLY)
FILL
VALVE
FLOAT
CUP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
ADJUSTABLE
HEIGHT
LOCK NUT
Fig. 10A
11
Turn on water supply.
Adjust water to water
level specified in the tank
by squeezing water level
adjustment clip and
moving FLOAT CUP up
or down along stainless
steel link.
SEAL REPLACEMENT:
1. Disconnect Chain.
2. Lift float up and remove flush valve seal by pulling seal
out of groove and sliding up over float.
3. Reverse procedure to install new seal.
TROUBLE SHOOTING FLUSH VALVE:
NOTE: DO NOT ADD ANY FOREIGN MATERIALS
TO THE SEALING SURFACE.
13 13a REFILL TUBE REPLACEMENT:
12
When cleaning your toilet, wash it with mild, soapy water, rinse
thoroughly with clear water and dry with a soft cloth.
WARNING: Do not use in-tank cleaners. These products can
seriously damage fittings in the tank. This damage can cause leakage
and property damage.
American Standard shall not be responsible or liable for any
damage caused by the use of in-tank cleaners.
!
CARE AND CLEANING
Locate bottom portion of
hose clip between the ribs (2)
on bottom of funnel inlet.
Note: Rotate funnel to position
ribs at rear of the tank.
FLOAT FLUSH
VALVE
SEAL

730529-100 Rev. M
- 5 -
14
IMPORTANT: Always clear
sand and rust from system.
Make sure water supply is off.
Remove valve TOP by lifting arm
and rotating top and arm 1/8 turn
counterclockwise, pressing down
slightly on cap.
LIFT ARM
FIRST
LIFT ARM
FIRST
While holding a container over
the uncapped VALVE to
prevent splashing, turn water
supply on and off a few times.
Leave water supply off.
Replace TOP by engaging lugs
and rotating 1/8 turn clockwise.
MAKE CERTAIN TIP IS
TURNED TO THE LOCKED
POSITION. VALVE MAY NOT
TURN ON IF TOP IS NOT
FULLY TURNED TO THE
LOCKED POSITION.
For troubleshooting information please contact:
Manufacturer's First Year Fill Valve Warranty:
TROUBLESHOOTING FILL VALVE
IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 14.
IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because:
• The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided.
• The flush valve is leaking because it's worn, dirty or misaligned (replace seal or flush valve).
IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster
Model 242 Replacement Seal may be needed.
© 2001 Fluidmaster, Inc.
® Registered trademark of Fluidmaster, Inc.
GUARANTEE: This Fluidmaster product is guaranteed to be free from defective materials and workmanship for a period of one year. Units returned to
Fluidmaster will be replaced without charge.
Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages
caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc.
See next page for American Standard Ten-Year "Worry-Free Decade" Warranty.
30800 Rancho Viejo Road
San Juan Capistrano, CA 92675
[phone] [phone]
www.fluidmaster.com
REPAIR PARTS LIST
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
Repair parts are determined by toilet tank number which can be found marked inside tank.
PART NO.
4260 Tank With
735100 Cover
4272 Tank With
735109 Cover
4272 Tank With
735117 Cover
4281 Tank With
735113 Cover
DESCRIPTION
738611-XXX0A
738835-XXX0A
738836-XXX0A
738837-XXX0A
034783-XXX0A
738565-409-0070A
738651-0070A
3175.002-0070A
738930-0070A
738657-0070A
738756-0070A
735100-400-XXX
735109-400-XXX
735117-400-XXX
735113-400-XXX
072989-0070A
Champion® Trip Lever
Champion® Trip Lever
Champion® Trip Lever
Champion® Trip Lever
Bolt Cap Kit (Incl 2 Covers & Washers)
Champion® Fluidmaster 400a Valve
Champion® Flush Valve Seal
Champion® Flush Valve Assembly
Champion® Bead Chain With Clevis Pin
Champion® Silicon Refill Tube
Champion® Tank To Bowl Coupling Kit #241
Champion® Tank Cover
Champion® Tank Cover
Champion® Tank Cover
Champion® Tank Cover
Clip for Refill Tube
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔

730529-100 Rev. M
CHAMPION® FLUSHING SYSTEM TEN-YEAR WORRY-FREE™ LIMITED WARRANTY
For this warranty to become effective, the accompanying warranty registration card and proof of purchase must be completed and
returned to the address on the warranty registration card within 30 days of purchase.
If inspection of this American Standard plumbing product, inclusive of china and all mechanical components, within ten years after its
initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the
product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this
product should check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty
maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it
has been modified in a manner inconsistent with the product as shipped by American Standard.
This warranty DOES NOT COVER any damage caused by the use of in-tank cleaners.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or
installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a
product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some
states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to
province, in which case this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product
was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:
- 6 -
In the United States:
American Standard Inc.
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
In Canada:
American Standard
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Does not flush
Poor or sluggish flush
Toilet leaks
Toilet does not shut off
a. Water supply valve closed.
b. Supply line blocked.
c. Flush valve chain too loose or disconnected.
d. Sand or debris lodged in water control.
a. Bowl water level too low.
b. Supply valve partly closed.
c. Partially clogged trapway and/or drain pipe and/or vent.
d. Supply pressure too low.
e. Flush valve chain too tight, pull rod not engaging.
a. Poor supply line connection.
b. Poor bowl to tank/floor connection.
a. Flush valve seal leaking or deformed.
b. Sand or debris lodged in water control.
a. Open valve and allow water to fill tank.
b. Shut off water supply, disconnect supply line and inspect all
gaskets and washers. Reassemble. Also, see Fluidmaster
maintenance. (see Step 14)
c. Readjust chain length as required.
d. Shut off water supply. Remove cap and clean as per Step 14.
a. Check that refill tube is connected to water control and
inserted into tank overflow without being kinked or damaged.
(see Step 13a)
b. Open supply valve fully. Be sure that proper supply tube size
is used.
c. Remove obstruction. Consult a plumber if necessary.
d. Normal supply pressure must be at least 20 psi.
e. Readjust chain length as needed. Review Step 10.
a. Review Step 9 of installation procedure.
b. Review Step 4 through 7 of installation procedure.
a. Clean debris from seal surface. Replace flush valve seal as
needed. (see Step 13)
b. Shut off water supply. Remove cap and clean as per Step 14.
TROUBLESHOOTING GUIDE
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
www.americanstandard-us.com
www.americanstandard.ca www.americanstandard.com.mx