American Standard Amarilis 8391.000 User manual

Installation
Instructions
.3&7
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
Roughing-in Dimensions Turn off hot and cold water
supplies before beginning.
CAUTION
BIDET FAUCET INSTALLATION
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and
screw on the ESCUTCHEON (4) until it locks against
the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Replace UPPER GASKET (7) and FRICTION RING (10).
Position the side threaded outlet rearward and secure
MOUNTING NUT (9). Thread ESCUTCHEON (5) onto
TRANSFER VALVE (8) until it seats against the
BIDET LEDGE.
Remove MOUNTING NUT (9), FRICTION RING (10)
and UPPER GASKET (7) from TRANSFER VALVE (8)
and insert into the center forward hole of BIDET.
COLD
HOT
BIDET
LEDGE
3
4
2
7
8
1
9
10
5
BIDET OUTLINE
IS SYMBOLIC
FINISHED
WALL
1-1/4 O.D. TAILPIECE
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
TRANSFER VALVE (FOR FLUSHING
RIM OR SPRAY)
DOUCHE SPRAY 2-1/8
DIA.
8391.000
BIDET FITTING
FINISHED
FLOOR
DIVERTER AND
VACUUM BREAKER
ASSEMBLY
1-1/4 MAX.
1-3/16 DIA.
(C) (H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
8 TO 12
2-1/4
DIA.
Congratulations on purchasing your American Standard faucet
with EverClean nish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
with EverClean™ Finish
*Hex key
*Wrench
*Supplied with Fitting
Flat Blade Screwdriver
Adjustable Wrench Channel Locks
Phillips Screwdriver
Required Tools
5VCJOH$VUUFS
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these nishes)

PUTTY
6
2
7
7
8
1
3
5
4
9
.3&7
DRAIN INSTALLATION
SPRAY INSTALLATION

Assemble O-RING (1), WASHER (2), PIVOT ROD (3)
and NUT (4) to DRAIN BODY (5). Concave side
of cup WASHER (2) is toward ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping
the PIVOT ROD (3) pointed towards
the back of the BIDET.
Push DRAIN ESCUTCHEON (10)
onto TAILPIECE (11).
Assemble SPRAY BODY (1) to BIDET.
Using putty, seal underside of SPRAY
BODY FLANGE (2) and secure with
NUT (3).
Screw SPRAY CAP (9) onto SPRAY BODY (1).
Screw SPRAY HOSE (4) with SEAL
WASHER (5) to SPRAY BODY (1).
Connect other end of HOSE (4) with
SEAL WASHER (6) to side outlet
NIPPLE (7) of the TRANSFER VALVE (8).
STOPPER
BIDET
PUTTY
CLIP
9
3
1
4
11
6
5
8
72
10
LIFT ROD GUIDE INSTALLATION

Unscrew LIFT ROD NUT (1) from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated into ESCUTCHEON of
LIFT ROD GUIDE (2).
Drop LIFT ROD GUIDE (2) into rear hole of bidet and from
below secure with ROD GUIDE NUT (1).
TEE AND HOSE CONNECTION

3
1
2
4
5
6
6
1
3
2
Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2)
to bottom of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE (5) and tighten
connection to ADAPTER (2)
Connect HOSE COUPLING NUTS (6) to Hot and Cold
valve bodies and securely tighten.
HANDLE INSTALLATION

See separate instruction sheet supplied with handle kit
for installation of handles.

.3&7
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean
water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
EverClean™ Finish Care Instructions


SERVICE
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Remove HANDLE and ADAPTER if present.
Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90pand replace.
Replace SPRING CLIP (1).
Replace HANDLE ASSEMBLY.
TEST INSTALLED FAUCET
With handles in OFF position, turn on
water supplies and check all connections
for leaks.
Replace Spray and operate
handles several times from
OFF to ON position. Do not
force, handles turn only 90˚.
Spray may accumulate dirt
causing distorted and reduced
water flow. Remove spray and
rinse clean.
Operate both handles to flush water lines
thoroughly. Turn diverter to rim wash and
bidet spray.
90p
1
2
WATER SUPPLY CONNECTIONS

Connect water supplies to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to proper length.
NOTE: FLEXIBLE SUPPLIES OR BULL NOSE RISERS ARE NOT INCLUDED
AND HAVE TO BE PURCHASED SEPARATELY.
3
2
FERRULE
COUPLING NUT
1
FINISH DRAIN INSTALLATION
Position EXTENSION ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Using metal TAILPIECE (5), make connection to the TRAP (6).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends
together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTENSION ROD (1)
and reassemble CLIP (4). (EXTENSION ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION ROD (1) and
tightening THUMBSCREW (3).
31
17
4
6
5
2