American Standard Enfield 2373.900 User manual

*Wrench
Certified to comply with ANSI A112.18.1M
Required Tools
*Supplied with Fitting
*Hex key
Adjustable Wrench Channel Locks
Flat Blade Screwdriver
DECK-MOUNT BATH FILLER
ENFIELD
MOUNTING
SURFACE
ADJ. 6-1/2 TO 12
8"
3-3/4"
5-3/16"
1-1/2 MAX.
1-1/4
MAX.
1-3/16 DIA.
3
(H)(C)
1-1/8 DIA.
8-3/16
12 MAX
2-1/16
DIA.
1-1/16 DIA.
3/4-14 MALE
N.P.T. INLETS
2-7/8"
LEVER
HANDLE
CROSS
HANDLE
2-1/4
DIA.
2-7/8
DIA.
M968288 Rev. 1.1
2373.900
2373.920
2373.901
2373.921
Installation
Instructions
ROUGHING-IN DIMENSIONS
with EverClean™ Finish
Congratulations on purchasing your American
Standard faucet with EverClean finish found
only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
IMPORTANT NOTICE TO INSTALLER!
Please check with local Code Authority for the installation requirements of this product. Some codes require an
additional temperature mixing valve to limit the maximum hot water temperature and vacuum breaker
(for products with hand spray) to be installed with this product.

SPOUT BASE
RECESS
Turn off hot and cold water
supplies before beginning.
CAUTION
12
Assemble RUBBER WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (1). Align SPOUT ASSEMBLY and from underside of ledge
secure SPOUT ASSEMBLY into position with LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
3
1
4
5
6
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
2
2
43
1
3
4
5
MOUNTING
SURFACE
SPOUT
ASSEMBLY
VALVE inlet is 3/4-inch NPT male.
NOTE
Install RING WASHER (1) into SPOUT BASE recess. Check
that O-RING (2) on end of SPOUT SHANK (3) is in place. Insert
SPOUT SHANK (3) through SPOUT ESCUTCHEON (4) and
into center hole on mounting surface.
2
ADJ. 6-1/2 TO 12
MOUNTING
SURFACE
M968288 Rev. 1.1
3
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8 or 8a) into TEE (5) and
attach to SPOUT SHANK (6) and tighten. Note: For product with Hand
Shower, COUPLING (8) is tightened using a 10mm (3/8”)
Hex Wrench.
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of
left VALVE and COLD water supply to
inlet of right VALVE using appropriate
connector.
VALVE ASSEMBLY
Thread of VALVE BODY (4) should extend at least 5/16 inch above
MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1).
FOR FITTING
LESS SPRAY
11
10
HOT
COLD
12
4
13
7
6
88a
5
13
12
34
MOUNTING
SURFACE
10
9
9
9
2
4
5/16'' MIN. MOUNTING
SURFACE
10
11
1

4INSTALL HANDLES
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. See figure "A". Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) or CROSS
HANDLE ASSEMBLY (5) by adjusting male teeth on ADAPTER (1) to
female teeth in HANDLE (4, 5).
Thread LEVER HANDLE ASSEMBLY (4) or CROSS HANDE ASSEMBLY (5)
onto DECK ADAPTER (6) until snug against mounting surface.
5SERVICE
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position. Unthread HANDLE BASE (1) from DECK
ADAPTER (2).
Pull HANDLE ASSEMBLY off VALVE STEM (3).
Remove SPRING CLIP (4). Lift STOP WASHER (5), turn 90° and replace.
Replace SPRING CLIP (4).
Find correct position of HANDLE ASSEMBLY by adjusting male teeth on
VALVE STEM (3) to female teeth in HANDLE.
Thread HANDLE ASSEMBLY onto DECK ADAPTER (2) until snug against
mounting surface.
2
90$
1
4
3
5
UNTHREAD
HANDLE ASSEMBLY
LOCKNUT
1
2
4 5
6
3
TOP
Figure "A"
SPLINE END DOWN
THREAD ON
TO DECK
ADAPTER
M968288 Rev. 1.1
HANDSHOWER INSTALLATION (FOR 2373.901/921)
6
1
2
3
5
7
8
10
9
9
11
4
6
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) and LOCKNUT (4) from
underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT.
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of COUPLING (7). on the SPOUT SHANK (6).
Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
ESCUTCHEON (1). Install SEALS (9) and connect both HOSES (8)
and (10), Connect HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE

9
Before the bathroom is completely finished, you may
want to remove spout, hand shower, and handles.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Lift TRANSFER ROD (8) and unscrew KNOB (2).
Remove PLUG BUTTON (3) and remove SET SCREW (4) using 5mm hex
wrench supplied.
Lift SPOUT (1) off SHANK (5) carefully and remove RUBBER
RING (6).
Unscrew SHANK SLEEVE (7) and lift TRANSFER ROD (8) from
SHANK (5).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (6) is properly seated in its recess at the base of SPOUT (1).
Make certain SET SCREW (5) is properly aligned and tight so that
SPOUT (1) is locked in place.
8
Hex wench, supplied
4
1
8
2
3
6
5
7
TEST INSTALLED FAUCET
7
Turn VALVES (1) to "off" position.
Lift HAND SHOWER (3) from holder, direct spray into tub, lift
TRANSFER KNOB (4) to check HAND SHOWER (3) and HOSES for leaks.
Turn VALVES "off."
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT (2) mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90°.
1 4
2
3
1
M968288 Rev. 1.1
EverClean™ Finish Care Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
©American Standard Inc. 2002
IN MEXICO 01-800-839-12-00